Failure Criterion for RC Members under Biaxial Bending and Axial Load
Publication: Journal of Structural Engineering
Volume 127, Issue 8
Abstract
A new failure surface and criterion are developed for prismatic reinforced concrete structural elements subjected to biaxial bending and axial load. The failure criterion is a smooth surface in 3D space (two moments and axial load). It is governed by eight parameters, four of which are strengths that can be computed directly from strain-based failure criteria. The remaining four are exponential coefficients whose values are calculated using optimization techniques. Since the failure criterion is intended for use in automated design-optimization procedures, methods for parameter estimation based on design of the RC structural element are developed and tested. The parameters of the proposed surface are calculated first by simply minimizing approximation errors and then by allowing only conservative approximation errors. A conclusion of this work is that the proposed methods are reliable and can be used to rapidly check allowable capacity constraints in load space during design optimization of reinforced concrete structures undergoing dynamic loading.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Arora, J. S. ( 1989). Introduction to optimum design, McGraw-Hill, New York.
2.
Arora, J. S., Chahande, A. I., and Paeng, J. K. ( 1991). “Multiplier methods for engineering optimization.” Int. J. Numer. Methods in Engrg., 32, 1485–1525.
3.
Atkinson, K. ( 1993). Elementary numerical analysis, Wiley, New York.
4.
Balling, R. J., and Yao, X. ( 1997). “How to optimize a reinforced concrete frame.” Guide to structural optimization, ASCE, Reston, Va., 123–138.
5.
Balling, R. J., Gallup, S. S., and McGrath, C. S. ( 1997). “How to optimize a reinforced concrete column or beam.” Guide to structural optimization, ASCE, Rep. No. 90, 55–73.
6.
Bresler, B. ( 1960). “Design criteria for reinforced columns under axial load and biaxial bending.” ACI J., 32, 481–490.
7.
Chahande, A. I., and Arora, J. S. ( 1994). “Optimization of large structures subjected to dynamic loads with the multiplier method.” Int. J. Numer. Methods in Engrg., 37, 413–430.
8.
Ferguson, P. M., Breen, J. E., and Jirsa, J. O. ( 1988). Reinforced concrete fundamentals, Wiley, New York.
9.
Fletcher, R. ( 1985). Practical methods of optimization, Wiley, New York.
10.
Gill, P. E., Murray, W., and Wright, M. H. ( 1981). Practical optimization, Academic, San Diego.
11.
Goldenberg, P., Silva, M. A., Pimenta, P. M, and Brasil, R. M. L. R. F. ( 1997). “Augmented Lagrangian optimization of a portal frame with elastoplastic behavior under dynamic loading.” 5th Pan-Am. Congr. on Appl. Mech., 373–376.
12.
Hulse, R., and Mosley, W. H. ( 1986). Reinforced concrete design by computer, Macmillan Education Ltd., New York.
13.
Hsu, C.-T.T. ( 1986). “Reinforced concrete members subject to combined biaxial bending and tension.” ACI J., 83(1), 137–144.
14.
Leet, K. ( 1991). Reinforced concrete design, McGraw-Hill, New York.
15.
Luenberger, D. G. ( 1984). Linear and nonlinear programming, Addison-Wesley, Reading, Mass.
16.
McCormac, J. C. ( 1988). Design of reinforced concrete, Addison Wesley Longman, New York.
17.
McGregor, J. G. ( 1992). Reinforced concrete, mechanics and design, Prentice-Hall, Englewood Cliffs, N.J.
18.
Muñoz, P. R., and Hsu, T.-C.C. (1997). “Behavior of biaxially loaded concrete-encased composite columns.”J. Struct. Engrg., ASCE, 123(9), 1163–1171.
19.
Nawy, E. G. ( 1990). Reinforced concrete: A fundamental approach, Prentice-Hall, Englewood Cliffs, N.J.
20.
Nilson, A. H., and Winter, G. ( 1986). Design of concrete structures, McGraw-Hill, New York.
21.
Pannell, F. N. ( 1963). “Failure surfaces for members in compression and biaxial bending.” ACI J., 60, 129–140.
22.
Put, B. M., Pi, Y., and Trahair, N. S. (1999). “Biaxial bending of cold-formed Z-beams.”J. Struct. Engrg., ASCE, 125(11), 1284–1290.
23.
Roddis, W. M. K., Lucas, W. K., and Chunnonond, V. ( 1996). “Single-criteria genetic optimization for design and detailing of concrete structures.” Proc., Computing Congr. III, ASCE, New York.
24.
Roddis, W. M. K., and Chunnanond, V. ( 1996). “Genetic algorithms applied to single-criteria optimization of reinforced concrete design and detailing.” SL Rep. 96-1, University of Kansas Center for Research, Lawrence, Kans.
25.
Rodríguez, J., Ortega, L. M., and Casal, J. ( 1996). “Loading bearing capacity of concrete columns with corroded reinforcement.” Corrosion of reinforcement in concrete construction, Royal Soc. of Chemistry, Cambridge, U.K., 220–232.
26.
Santos, L. M. ( 1994). Sub-rotinas básicas do dimensionamento de concreto armado, Thot Editora Ltda., São Paulo, Brazil (in Portuguese).
27.
Silva, M. A., Arora, J. S., Swan, C. C., and Brasil, R. M. L. R. F. ( 2000). Optimization of elevated concrete foundations for vibrating machines, in press.
28.
Spiegel, L., and Limbrunner, G. F. ( 1998). Reinforced concrete design, Prentice-Hall, Upper Saddle River, N.J.
29.
Sussekind, J. C. ( 1979). Curso de concreto, Editora Globo, Rio de Janeiro, Brazil (in Portuguese).
Information & Authors
Information
Published In
History
Received: May 31, 2000
Published online: Aug 1, 2001
Published in print: Aug 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.