Local and Postlocal Buckling of Fabricated Steel and Composite Cross Sections
Publication: Journal of Structural Engineering
Volume 127, Issue 6
Abstract
Composite sections are being increasingly used as columns in multistory buildings. These sections provide considerable economy as they eliminate plywood formwork and allow large percentages of steel to be utilized in their application. The initial local buckling load of these sections is enhanced by the presence of the concrete infill and this allows very slender steel plates to be used in their fabrication. This paper investigates the local and postlocal buckling behavior of welded sections as box or wide flange I-sections. An extensive set of experiments was conducted on both hollow and concrete-filled steel box sections. Furthermore, a detailed study of flange outstands with and without concrete infill is considered in this paper. A numerical model based on the finite strip method is used to determine the initial local buckling stress incorporating residual stresses, and this is shown to agree well with the experiments. Finally, an effective width model developed elsewhere and presented in existing international codes is augmented and calibrated with the test results. This method is found to be useful in determining the axial compressive strength of these cross sections.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bradford, M. A. ( 1987). “Inelastic local buckling of fabricated I-beams.” J. Constr. Steel Res., 7, 317–334.
2.
Bradford, M. A. ( 1995). “Local and post-local buckling of fabricated box members.” Civ. Engrg. Trans., Canberra, Australia, 27(4), 391–396.
3.
Bradford, M. A., Bridge, R. Q., Hancock, G. J., Rotter, J. M., and Trahair, N. S. ( 1987). “Australian limit state design rules for the stability of steel structures.” Proc., 1st Struct. Engrg. Conf., Institution of Engineers, Australia, Melbourne, Australia, 209–216.
4.
Bridge, R. Q., and O'Shea, M. D. ( 1998). “Behaviour of thin-walled steel box sections with or without internal restraint.” J. Constr. Steel Res., 47(1–2), 73–92.
5.
British Standards Institution (BSI). ( 1993). “Design of steel structures, part 1.1: General rules and rules for buildings.” Eurocode 3, London.
6.
Broderick, B. M., and Elnashai, A. S. ( 1994). “Seismic resistance of composite beam-columns in multi-storey structures. Part 2: Analytical model and discussion or results.” J. Constr. Steel Res., 30(3), 231–258.
7.
Cheung, Y. K. ( 1976). Finite strip method in structural analysis, Pergamon, Tarrytown, N.Y.
8.
Dawe, J. L., and Kulak, G. L. (1984). “Plate instability for W shapes.”J. Struct. Engrg., ASCE, 110(6), 1278–1291.
9.
Faber, O. ( 1956). “Savings to be effected by the more rational design of cased stanchions as a result of recent full-size tests.” The Struct. Engr., London, 88–109.
10.
Furlong, R. W. (1967). “Strength of steel-encased concrete beam columns.”J. Struct. Div., ASCE, 93(5), 113–124.
11.
Hajjar, J. F., and Gourley, B. C. (1996). “Representation of concrete-filled steel tube cross-section strength.”J. Struct. Engrg., ASCE, 122(11), 1327–1336.
12.
Kitipornchai, S., and Wong-Chung, A. D. (1987). “Inelastic buckling of welded monosymmetric I-beams.”J. Struct. Engrg., ASCE, 113(4), 740–756.
13.
Knowles, R. B., and Park, R. (1969). “Strength of concrete-filled tubular columns.”J. Struct. Div., ASCE, 95(2), 2565–2587.
14.
Knowles, R. B., and Park, R. (1970). “Axial load for concrete-filled steel tubes.”J. Struct. Div., ASCE, 96(10), 2125–2155.
15.
Moore, W. P., Jr. ( 1988). An overview of composite construction in the United States; Composite construction in steel and concrete, C. D. Buckner and I. M. Viest, eds., ASCE, New York.
16.
Standards Australia (SA). ( 1998). “Australian standard—Steel structures.” AS4100, Australia.
17.
Stevens, R. F. ( 1959). “Encased steel stanchions and BS449.” Engineering, 376–377.
18.
El-Tawil, S., and Deierlein, G. G. (1999). “Strength and ductility of concrete-encased composite columns.”J. Struct. Engrg., ASCE, 125(9), 1009–1019.
19.
Tremblay, R., Chicoine, T., and Masicotte, B. ( 2001). “Design equation for the axial capacity of partially encased noncompact columns.” Proc., Engrg. Found. Conf., ASCE, Reston, Va., in press.
20.
Uy, B. ( 1998). “Local and post-local buckling of concrete filled steel welded box columns.” J. Constr. Steel Res., 47(1–2), 47–72.
21.
Uy, B. (2000). “Strength of concrete-filled steel box columns incorporating local buckling.”J. Struct. Engrg., ASCE, 126(3), 341–352.
22.
Uy, B., and Bradford, M. A. ( 1995). “Local buckling behaviour of profiled trough girders composed of an assemblage of profiled steel sheets.” Thin-Walled Struct., 22(2), 97–120.
23.
Uy, B., and Bradford, M. A. ( 1996). “Elastic local buckling of steel plates in composite steel-concrete members.” Engrg. Struct., 18(3), 193–200
24.
Webb J., and Payton, J. J. ( 1990). “Composite concrete-filled steel tube columns.” Proc., Struct. Engrg. Conf., Institution of Engineers Australia, Australia, 181–185.
25.
Wright, H. D. ( 1993). “Buckling of plates in contact with a rigid medium.” The Struct. Engr., London, 71(12), 209–215.
26.
Wright, H. D. (1995). “Local stability of filled and encased steel sections.”J. Struct. Engrg., ASCE, 121(10), 1382–1388.
Information & Authors
Information
Published In
History
Received: Mar 30, 2000
Published online: Jun 1, 2001
Published in print: Jun 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.