Design Equation for Overlap Tubular K-Joints under Axial Loading
Publication: Journal of Structural Engineering
Volume 126, Issue 7
Abstract
Using a previously presented finite-element study of axially loaded overlap tubular K-joints as a platform, this paper presents further work that aimed at extending and enhancing the strength estimation equation already presented. The current work includes extending the θ (brace angle) validity range to 30° ≤ θ ≤ 60°; investigating the effects of the yield stress/ultimate tensile strength ratio and the brace/chord yield stress ratio; exploring the influence of loading reversal; and quantifying the reduction in strength caused by the absence of the hidden weld. The end result of these studies is a new, extended capacity equation. The accuracy of the proposed equation to predict the axial capacity of test joints was established by assessing it using an experimental database. The applicability of the proposed equation for design practice was further ascertained by investigating strength sensitivities to material curve variations, different chord end support conditions, and joints with unequal brace inclinations. The proposed design equation is found to be both accurate and conservative and is therefore recommended to be used in practice.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Petroleum Institute (API). (1993). “Planning, designing and constructing fixed offshore platforms,” API RP 2A, 20th Ed., Washington, D.C.
2.
Bolt, H. M., Seyed-Kebari, H., and Ward, J. K. (1992). “The influence of chord length and boundary conditions on K joint capacity.” 2nd Int. Offshore and Polar Engrg. Conf., Balkema, Rotterdam, The Netherlands, 4, 347–354.
3.
Comité International pour le Developpement et l'Étude de la Construction Tubulaire (CIDECT). (1991). Design guide for circular hollow section (CHS) joints under predominantly static loading. Paris, France.
4.
Davies, G., and Crockett, P. (1994). “Effect of the hidden weld on RHS partial overlap K joint capacity.” 6th Int. Symp. on Tubular Struct., Balkema, Rotterdam, The Netherlands, 573–579.
5.
Dexter, E. M., and Lee, M. M. K. (1999a). “Static strength of axially loaded tubular K-joints. I: Behavior.”J. Struct. Engrg., ASCE, 125(2), 194–201.
6.
Dexter, E. M., and Lee, M. M. K. (1999b). “Static strength of axially loaded tubular K-joints. II: Ultimate capacity.”J. Struct. Engrg., ASCE, 125(2), 202–210.
7.
Dexter, E. M., Lee, M. M. K., and Kirkwood, M. G. (1996). “Overlapped K joints in circular hollow sections under axial loading—An investigation of the factors affecting static strength using numerical modelling.” J. Offshore Mech. and Arctic Engrg., ASME, New York, 118, 53–61.
8.
Dier, A. F., and Lalani, M. (1998). “New code formulations for tubular joint static strength.” 8th Int. Symp. on Tubular Struct., Balkema, Rotterdam, The Netherlands, 107–116.
9.
Gazzola, F., and Lee, M. M. K. (1998). “Further numerical study and strength formulation of axially loaded overlap K-joints.” Res. Rep. CR/991/98, University of Wales Swansea, U.K.
10.
Health and Safety Executive (HSE). (1990). Offshore installations: Guidance on design, construction and certification, 4th Ed., London (withdrawn).
11.
Healy, B. E. (1994). “A numerical investigation into the capacity of overlap circular K-joints.” 6th Int. Symp. on Tubular Struct., Balkema, Rotterdam, The Netherlands, 563–571.
12.
International Organization for Standardization (ISO). ( 1999). “Petroleum and natural gas industries—Offshore structures. Part 2: Fixed steel structures.” ISO 13819-2, (draft ISO/TC67/SC7), Genève, Switzerland.
13.
Joint industry funded research programme. Analytical and experimental investigation of the behaviour of tubular frames, Phase II. (1992). Vol. 1, BOMEL Engineering Ltd., Maidenhead, U.K.
14.
Kurobane, Y., Makino, Y., and Ochi, K. (1984). “Ultimate resistance of unstiffened tubular joints.”J. Struct. Engrg., ASCE, 110(2), 385–400.
15.
Kurobane, Y., Ogawa, K., Ochi, K., and Makino, Y. (1986). “Local buckling of braces in tubular K-joints.” Thin-Walled Struct., 4, 23–40.
16.
Lee, M. M. K., Dexter, E. M., and Kirkwood, M. G. (1995). “Strength of moment-loaded tubular T/Y-joints in offshore platforms.” The Struct. Engr., London, 73(15), 239–246.
17.
Makino, Y., Kurobane, Y., Ochi, K., van der Vegte, G. J., and Wilmshurst, S. R. (1996). “Introduction to unstiffened CHS tubular joint database.” 7th Int. Symp. on Tubular Struct., Miskolc, Hungary, 157–164.
18.
Yura, J. A., Zettlemoyer, N., and Edwards, I. F. (1980). “Ultimate capacity equations for tubular joints.” Offshore Technol. Conf. 3690, Houston, Tex.
Information & Authors
Information
Published In
History
Received: Dec 23, 1998
Published online: Jul 1, 2000
Published in print: Jul 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.