Analysis of Reinforced Concrete Beams Strengthened with FRP Laminates
Publication: Journal of Structural Engineering
Volume 126, Issue 6
Abstract
A significant percentage of the bridges in North America were built after the Second World War. Most of them were originally designed for smaller vehicles, lighter loads, and a lower traffic volume than commonly experienced today. A study reported by Klaiber et al. indicates that over 50% of all bridges in the United States were built before 1940, and approximately 42% of these bridges are considered to be structurally deficient. This alarming statistic underscores the importance of developing reliable and cost-effective repair and strengthening techniques for existing bridge structures. A particularly challenging problem in this area is the rehabilitation of reinforced concrete structures. In recent years, the repair of understrengthened or damaged reinforced concrete members by the external bonding of fiber-reinforced polymer (FRP) laminates has received considerable attention. This paper investigates the flexural behavior of reinforced concrete beams strengthened with externally bonded FRP laminates. A simple and direct analytical procedure for evaluating the ultimate flexural capacity of FRP strengthened reinforced concrete flexural members is presented. The procedure is derived from equilibrium equations and compatibility of strains and is applicable to both singly and doubly reinforced concrete rectangular sections, as well as flanged sections. The procedure is validated by comparisons with results of experimental data available in the literature. Upper and lower limits of FRP that may be bonded to a reinforced concrete cross section to ensure ductile behavior are established, and design nomographs to facilitate implementation of the procedure are presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Concrete Institute (ACI). (1995). Building code requirements for structural concrete (ACI 318-95) and commentary (ACI 318R-95), American Concrete Institute, Detroit, Mich.
2.
An, W., Saadatmanesh, H., and Ehsani, M. R. (1991). “RC beams strengthened with FRP plates. II: analysis and parametric study.”J. Struct. Engrg., ASCE, 117(11), 3434–3455.
3.
Arduini, M., and Nanni, A. (1997). “Parametric study of beams with externally bonded FRP reinforcement.” ACI Struct. J., 94(5), 493–501.
4.
Chajes, M. J., Thomson, T. A., Januszka, T. F., and Finch, W. W. (1994). “Flexural strengthening of concrete beams using externally bonded composite.” Constr. and Build. Mat., 8(3), 191–201.
5.
Klaiber, F. W., Dunker, K. F., Wipf, T. J., and Sanders, W. W. (1987). “Methods of strengthening existing highway bridges.” NCHRP Res. Rep. No. 293, Transportation Research Board, Washington, D.C.
6.
Malek, A. M., and Saadatmanesh, H. (1998). “Design equations and guidelines for reinforced concrete beams strengthened with FRP plates.” Proc., 2nd Int. Conf. on Compos. in Infrastruct., University of Arizona, Tucson, Ariz., 603–617.
7.
Meier, U., and Kaiser, H. (1991). “Strengthening structures with CFRP laminates.” Proc., Advanced Compos. Mat. in Civ. Engrg. Struct., ASCE, New York, 224–232.
8.
Norris, T., and Saadatmanesh, H. (1997). “Shear and flexural strengthening of RC beams with carbon fiber sheets.”J. Struct. Engrg., ASCE, 23(7), 903–911.
9.
Quantrill, R. J., Holloway, L. C., and Thorne, A. M. (1996). “Predictions of the maximum plate end stresses of FRP strengthened beams: part II.” Mag. Concrete Res., 48(177), 343–351.
10.
Ritchie, P. A. ( 1988). “External reinforcement of concrete beams using fiber reinforced plastic.” PhD thesis, Lehigh University, Bethlehem, Pa.
11.
Ross, C. A., Jerome, D. M., Tedesco, J. W., and Hughes, M. L. (1999). “Strengthening of reinforced concrete beams with externally bonded composite laminates.” ACI Struct. J., 96(2), 212–220.
12.
Saadatmanesh, H., and Ehsani, M. (1990). “Fiber composite plates can strengthen beams.” Concrete Int., 3, 65–71.
13.
Saadatmanesh, H., and Ehsani, M. R. (1991). “RC beams strengthened with GFRP plates. I: experimental study.”J. Struct. Engrg., ASCE, 117(11), 3417–3433.
14.
Saadatmanesh, H., and Malek, A. M. (1998). “Design guidelines for flexural strengthening of RC beams and FRP plates.”J. Compos. for Constr., ASCE, 2(4), 158–164.
15.
Sharif, A., Al-Sulaimani, G. J., Basunbul, I. A., Baluch, M. H., and Ghaleb, B. N. (1994). “Strengthening of initially loaded reinforced concrete beams using FRP plates.” ACI Struct. J., 91(2), 160–168.
16.
Tedesco, J. W., and El-Mihilmy, M. T. (1999). “Design and behavior of reinforced concrete beams strengthened with FRP.” Final Rep., Alabama Department of Transportation, Montgomery, Ala.
17.
Triantafillou, T. C., and Plevris, N. (1992). “Strengthening of RC beams with epoxy bonded fibre composite materials.” Mat. and Struct., 25, 201–211.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 126 • Issue 6 • June 2000
Pages: 684 - 691
History
Received: Jul 6, 1999
Published online: Jun 1, 2000
Published in print: Jun 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.