Composite Action in Concrete Filled Tubes
Publication: Journal of Structural Engineering
Volume 125, Issue 5
Abstract
This paper studies composite action in concrete filled tubes (CFT) that have dimensions and proportions like those used in U.S. practice. CFT applications in buildings and the importance of bond stress and interface conditions to behavior are noted, past research is summarized, and the combined results are analyzed. An experimental study is described and evaluated. It is shown that shrinkage can be very detrimental to bond stress capacity, and the importance of shrinkage depends upon the characteristics of the concrete, the diameter of the tube, and the surface condition at the inside of the tube. The bond capacity is smaller with large diameter tubes and large d/t ratios. The bond capacity is interrelated with slip at the steel concrete interface. An exponential distribution of bond stress is expected prior to slip, and a more uniform distribution occurs after slip. An equation that estimates the bond stress capacity is developed, and this leads to design recommendations at different performance levels.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AIJ standards for structural calculation of steel reinforced concrete structures . (1991). Architectural Institute of Japan, Tokyo.
2.
Cameron B. ( 1997). “Bond behavior in concrete filled tube composite columns,” Ms thesis, University of Washington, Seattle.
3.
Emoto, J. ( 1996). “Bond shear demand in composite concrete and steel members,” University of Washington, Seattle.
4.
Morishita, Y., and Tomii, M. ( 1982). “Experimental studies on bond strength between square steel tube and encased concrete core under cyclic shearing force and constant axial loads.” Trans. Japan Concrete Inst., Tokyo, 4, 115–122.
5.
Morishita, Y., Tomii, M., and Yoshimura, K. ( 1979a). “Experimental studies on bond strength in concrete filled circular steel tubular columns subjected to axial loads.” Trans. Japan Concrete Inst., Tokyo, 1, 351–358.
6.
Morishita, Y., Tomii, M., and Yoshimura, K. ( 1979b). “Experimental studies on bond strength in concrete filled on square and octagonal steel tubular columns subjected to axial loads.” Trans. Japan Concrete Inst., Tokyo, 1, 359–366.
7.
Shakir-Khalil, H. ( 1991). “Bond strength in concrete-filled steel hollow section.” Int. Conf. on Steel and Aluminum Struct., Elsevier Science, 22–24, 157–168.
8.
Shakir-Khalil, H. ( 1993a). “Pushout strength of concrete-filled steel hollow sections.” The Struct. Engr., 71(13), 230–233.
9.
Shakir-Khalil, H. ( 1993b). “Resistance of concrete-filled steel hollow tubes to pushout forces.” The Struct. Engrg., 71(13), 234–243.
10.
Tomii, M. ( 1984). “Bond check for concrete-filled steel tubular columns.” Composite and mixed construction. ASCE, Reston, Va., 195–214.
11.
Tomii, M., Yoshimura, K., and Morishita, Y. ( 1980a). “A method of improving bond strength between steel tube and concrete core cast in square and octagonal steel tubular columns.” Trans. Japan Concrete Inst., Tokyo, 2, 107–114.
12.
Tomii, M., Yoshimura, K., and Morishita, Y. ( 1980b). “A method of improving bond strength between steel tube and concrete core cast in circular steel tubular columns.” Trans. Japan Concrete Inst., 2, 99–106.
13.
Uniform building code, structural engineering design provisions . (1994). Vol. 2, International Conference of Building Officials, Whittier, Calif.
14.
Virdi, K. S., and Dowling, P. J. ( 1975). “Bond strength in concrete filled circular steel tubes.” CESLIC Rep. CC11, Engrg. Struct. Lab., Civ. Engrg. Dept., Imperial College, London.
Information & Authors
Information
Published In
History
Received: Mar 2, 1998
Published online: May 1, 1999
Published in print: May 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.