Seismic Reliability of Special Moment Steel Frames with Welded Connections: I
Publication: Journal of Structural Engineering
Volume 125, Issue 4
Abstract
The Northridge earthquake of 1994 led to numerous weld fractures in beam-to-column connections in welded special moment-resisting frames. To address building performance issues raised by these failures and to support improvements in probability-based load resistance factor design for steel building structures, four welded special moment-resisting frames of different sizes and configurations that suffered connection damage during the earthquake are evaluated using both deterministic and stochastic approaches. The results of this investigation are presented in two companion papers. This paper focuses on deterministic dynamic modeling issues, using a new hysteretic model that incorporates the effects of connection weld fractures on building response and ground motions believed to be representative of the Northridge earthquake. The degraded connection model results in somewhat larger frame deformations, but its impact only becomes significant at spectral accelerations larger than those believed to have occurred. The agreement of predicted and surveyed damage was quite good for two of the frames, but not as good for the other two. Inherent randomness and modeling uncertainties limit the quality of the agreement that is possible from a single deterministic analysis. Thus, in the companion paper, the role of uncertainties in making such comparisons is investigated. Randomizing the strength and ground motion yields a probabilistic description of building performance that places such comparisons of predicted and observed damage in better perspective.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ang, K. M., and Morris, G. A. ( 1984). “Analysis of three-dimensional frames with flexible beam-column connections.” Can. J. Civ. Engrg., Ottawa, 11(2), 245–254.
2.
Blume, J. A., Newark, N. M., and Corning, L. H. ( 1961). Design of multistory reinforced concrete buildings for earthquake motions . Portland Cement Association, Skokie, Ill.
3.
Bouc, R. ( 1967). “Forced vibration of mechanical systems with hysteresis.” Proc., 4th Conf. on Nonlinear Oscillation.
4.
Campbell, H. H. ( 1995). “The Northridge fractures: Are we learning the right lessons?” Civ. Engrg., 65(3), 62–65.
5.
Chen, W. F., and Kishi, N. (1989). “Semirigid steel beam-to-column connections: Data base and modeling.”J. Struct. Engrg., ASCE, 115(1), 105–119.
6.
Chen, W. F., and Lui, E. M. ( 1991). Stability design of steel frames . CRC, Boca Raton, Fla.
7.
Coats, D. W., Jr. ( 1989). “Damping in building structures during earthquakes, test data and modeling.” Rep. No. NUREG/CR-3006, U.S. Nuclear Regulatory Commission, Washington, D.C.
8.
FEMA. ( 1995). “Interim guideline: Evaluation, repair, modification and design of welded steel moment frame structures.” Report FEMA-267, Federal Emergency Management Agency, Washington, D.C.
9.
Frye, M. J., and Morris, G. A. ( 1976). “Analysis of flexibly connected steel frames.” Can. J. Civ. Engrg., Ottawa, 2(3), 280–291.
10.
Graves, R. W., Somerville, P. G., and McLaren, J. P. ( 1995). “Ground motion time histories of the 1994 Northridge earthquake at three sites.” Rep. Prepared for National Institute of Standards and Technology by Woodward-Clyde Federal Services, Pasadena, Calif.
11.
Gross, J. L. ( 1998). “A connection model for the seismic analysis of welded steel moment fames.” Engineering Structures, 20(4–6), 390–397.
12.
Johnson, R. P., and Law, C. L. C. ( 1981). “Semi-rigid joints for composite frames.” Joints in structural steelwork, Wiley, New York, 3.3–3.19.
13.
Kaufmann, E. J., Fisher, J. W., Di Julio, R. M., Jr. and Gross, J. L. ( 1997). “Failure analysis of welded steel moment frames damaged in the Northridge earthquake.” Rep. No. NISTIR 5944, National Institute of Standards and Technology, Gaithersburg, Md.
14.
Krawinkler, H. ( 1978). “Shear in beam-column joints in seismic design of steel frames.” Engrg. J., Third Quarter, 82–91.
15.
Kunnath, S. K. ( 1995). “Enhancements to program IDARC: Modeling I behavior of welded connections in steel moment-resisting frames.” Rep. No. NIST GCR 95-673, National Institute of Standards and Technology, Gaithersburg, Md.
16.
Kunnath, S. K., Reinhorn, A. M., and Lobo, R. F. ( 1992). “IDARC version 3.0: A program for the inelastic damage analysis of reinforced concrete structures.” Tech. Rep. NCEER-92-0022, Nat. Ctr. for Earthquake Engrg. Res., State University of New York at Buffalo, Buffalo, N.Y.
17.
Lindsey, S. D. ( 1987). “Design of frames with PR connections.” Joint flexibility in steel frames, Elsevier Science, New York, 251–260.
18.
Load and resistance factor design specification for structural steel buildings (LRFD) . (1993). American Institute of Steel Construction, Chicago, Ill.
19.
Maxwell, S. M., Jenkins, W. M., and Howlett, J. H. ( 1981). “A theoretical approach to the analysis of connection behavior.” Joints in structural steelwork, Wiley, New York, 2.49–2.69.
20.
Miller, D. K. ( 1994). “Northridge: The role of welding clarified.” Welding Innovation Quarterly, XI(2).
21.
NEHRP Recommended Provisions for the Development of Seismic Regulations for New Buildings (1995). Building Seismic Safety Council, Vols. 1 and 2, prepared for and issued by the Federal Emergency Management Agency, Washington, D.C.
22.
Prakash, V., Powell, G. H., and Filippou, F. ( 1992). “DRAIN-2DX: Base program user guide.” SEMM Rep. 92-29. University of California, Berkeley, Calif.
23.
Recommended Lateral Force Requirements and Commentary . (1990). Seismology Committee, Structural Engineers Association of California, Sacramento, Calif.
24.
SAC. ( 1996). “Experimental investigations of beam-column subassemblages.” Rep. No. SAC-96-01, Parts 1 and 2, SAC Joint Venture, Sacramento, Calif.
25.
Somerville, P., Graves, R., and Saikia, C. ( 1995). “Characterization of ground motions during the Northridge earthquake of January 17, 1994.” Rep. No. SAC-95-03, SAC Joint Venture, Sacramento, Calif.
26.
Sommer, W. H. ( 1969). “Behavior of welded header plate connections,” PhD thesis, University of Toronto, Toronto, ON, Canada.
27.
Song, J. ( 1998). “Seismic reliability evaluation of steel frames with damaged welded connections,” PhD dissertation, Johns Hopkins University, Baltimore, Md.
28.
Song, J., and Ellingwood, B. R. (1999). “Seismic reliability of special moment steel frames with welded connections: II.”J. Struct. Engrg., ASCE, 125(4), 372–384.
29.
Tide, R. H. R., Fisher, J. W., and Kaufmann, E. J. ( 1996). “Substandard welding quality exposed: Northridge, California earthquake, January 17, 1994.” Proc., Asian Pacific Welding Congr.
30.
Uang, C. M., Yu, Q. S., Sadre, A., Bonowitz, D., and Youssef, N. ( 1995). “Performance of a 13-story steel moment-resisting frame damaged in the 1994 Northridge earthquake.” Tech. Rep. No. SAC 95-04, SAC Joint Venture, Sacramento, Calif.
31.
Uniform building code . (1994). International Conference of Building Officials, Whittier, Calif.
32.
When, Y. K. (1976). “Method for random vibration of hysteretic systems.”J. Engrg. Mech. Div., ASCE, 102(2), 249–263.
33.
Xue, M., Kaufmann, E. J., Lu, L. W., and Fisher, J. W. ( 1998). “Fracture and ductility of welded moment connections under dynamic loading.” Proc., Struct. Congr., Vol. 1, ASCE, Reston, Va., XV, 607–613.
34.
Youssef, N., and Gross, J. L. ( 1995). “A survey of steel moment-resisting frame buildings affected by the 1994 Northridge earthquake.” Rep. No. NISTIR 5625, National Institute of Standards and Technology, Gaithersburg, Md.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 125 • Issue 4 • April 1999
Pages: 357 - 371
History
Received: Apr 30, 1998
Published online: Apr 1, 1999
Published in print: Apr 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.