Three-Dimensional Failure Analysis of Composite Masonry Walls
Publication: Journal of Structural Engineering
Volume 122, Issue 9
Abstract
Results of three-dimensional (3D) finite-element failure analysis of composite masonry walls subjected to both vertical and horizontal loads are presented in this paper. The wall is modeled by using eight-noded solid elements and cracking at the interfaces is defined by a simple Mohr-Coulomb failure criterion. The smeared crack technique is used to model the cracks. It is shown that cracking in the collar joint is initiated at a much smaller magnitude of the horizontal inplane load compard to the vertical load. This phenomenon may be attributed to the relatively high rigidity of the wall in the vertical direction. The failure loads for composite walls are computed using the 3D analysis and are compared with those obtained from an approximate method and experimental values. It is shown that the computed failure loads follow the same trend as the experimental results.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Anand, S. C. (1985). “Shear stresses in composite masonry walls.”New analysis techniques in composite masonry, ASCE, New York, N.Y., 106–127.
2.
Anand, S. C., and Gandhi, A. (1983). “A finite element model to compute stresses in composite masonry walls due to temperature, moisture, and creep.”Proc., 3rd Can. Masonry Symp. 83, 34.1–34.20.
3.
Anand, S. C., and Rahman, M. A. (1991). “Numerical modelling of creep in composite masonry walls.”J. Struct. Engrg., ASCE, 117(7), 2149– 2165.
4.
Anand, S. C., and Rahman, M. A.(1994). “Accurate estimation of interface shear stresses in composite masonry walls.”J. Struct. Engrg., ASCE, 120(3), 998–1015.
5.
Anand, S. C., and Stevens, D. J. (1984). “A simple model for shear cracking and failure in composite masonry.”Proc., 6th Int. Congr. on Fracture, 2915–2922.
6.
Anand, S. C., and Yalamanchili, K. K. (1988). “A quasi-three dimensional failure analysis of composite masonry walls subjected to seismic loads.”Proc., 8th Int. Brick/Block Masonry Conf., Elsevier Applied Science, London, England, 1205–1216.
7.
Anand, S. C., and Yalamanchili, K. K.(1993). “A numerical procedure to compute failure loads in composite masonry walls.”Struct. Engrg. Rev., 5(1), 53–61.
8.
Anand, S. C., and Young, D. T.(1982). “A finite element model for composite masonry.”J. Struct. Div., ASCE, 108(12), 2637–2648.
9.
Anand, S. C., Yalamanchili, K. K., and Rahman, M. A. (1991). “Stiffness effects on the maximum shear stress in the collar joint of a composite masonry wall.”Proc., 9th Brick/Block Masonry Conf., Deutsche Gesellschaft fuer Mauerwerksbau, Bonn, Germany, 980–987.
10.
Chen, W. F. (1982). Plasticity in reinforced concrete . McGraw-Hill Book Co., Inc., New York, N.Y.
11.
Colville, J., Matty, S., and Wolde-Tinsae, A. (1987). “Shear capacity of mortared collar joints.”Proc., 4th North Am. Masonry Conf., The Masonry Soc., Boulder, Colo., 60.1–60.15.
12.
Hamid, A. A., and Drysdale, R. G.(1979). “Shear strength of concrete masonry joints.”J. Struct. Div., ASCE, 105(7), 1227–1240.
13.
Hamid, A. A., and Drysdale, R. G.(1982). “The shear strength of brickwork bed joints.”Proc., British Cer. Soc., Stoke-on-Trent, England, 30, 101–109.
14.
Matty, S. A., Colville, J., and Wolde-Tinsae, A. M. (1988). “Load transfer in composite masonry.”Proc., 8th Int. Brick/Block Masonry Conf., Elsevier Applied Science, London, England, 372–383.
15.
McCarthy, J. A., Brown, R. H., and Cousins, T. E. (1985). “An experimental study of the shear strength of the collar joint in grouted and slushed composite masonry walls.”Proc., 3rd North Am. Masonry Conf., The Masonry Society, Boulder, Colo., 39.1–39.16.
16.
Porter, M. L., Wolde-Tinsae, A. M., and Ahmed, M. H. (1986). “Strength analysis of composite walls.”Proc., ASCE Struct. Congr. '86, ASCE, New York, N.Y., 94–110.
17.
Rahman, M. A. (1986). “Earthquake effects on composite masonry walls.”Proc., 3rd U.S. Nat. Conf. on Earthquake Engrg., Earthquake Engrg. Res. Inst., El Cerrito, Calif., 2667–2682.
18.
Rahman, M. A. (1989). “Analytical investigations of the behavior and failure of composite masonry walls,” PhD dissertation, Clemson Univ., Clemson, S.C.
19.
Rahman, M. A., and Anand, S. C.(1992). “Thermal stress in composite masonry walls.”The Masonry Soc. J., 11(1), 21–28.
20.
Rahman, M. A., and Anand, S. C.(1994). “An empirical Mohr-Coulomb failure criterion for concrete-block mortar joints.”J. Struct. Engrg., ASCE, 120(8), 2408–2422.
21.
Rao, M. (1989). “Experimental evaluation of composite masonry walls subjected to shear and axial loads,” Master's thesis, Clemson Univ., Clemson, S.C.
22.
Self, M. W. (1983). “Design guidelines for composite clay brick and concrete block masonry. Part I: Composite masonry prisms.”Res. Rep., Dept. of Civ. Engrg., Univ. of Florida, Gainesville, Fla.
23.
Williams, R. T., and Geschwindner, L. F. (1982). “Shear stress across collar joints in composite masonry walls.”Proc., 2nd North Am. Masonry Conf., The Masonry Soc., Boulder, Colo., 8.1–8.17.
24.
Yalamanchili, K. K. (1990). “Finite element computations on supercomputers and their applications to failure analysis of composite masonry walls,” PhD dissertation, Clemson Univ., Clemson, S.C.
25.
Yalamanchili, K. K., and Anand, S. C.(1993). “Use of sparse diagonal storage in finite element analysis.”Comp. and Struct., 46(6), 963–967.
26.
Yalamanchili, K. K., Anand, S. C., and Warner, D. D.(1992). “Three dimensional finite element analysis on a hypercube computer.”Comp. and Struct., 42(1), 11–20.
Information & Authors
Information
Published In
Copyright
Copyright © 1996 American Society of Civil Engineers.
History
Published online: Sep 1, 1996
Published in print: Sep 1996
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.