Nominal Strength of Composite Prestressed Concrete Bridge Deck Panels
Publication: Journal of Structural Engineering
Volume 121, Issue 2
Abstract
Precast prestressed concrete panels have been used as subdecks in bridge construction. To experimentally investigate the nominal flexural and shear strengths of this composite slab system, five full-scale model composite slab specimens were constructed and tested. One specimen modeled bridge deck condition well within a girder span, and the other four specimens represented geometric conditions that occur with skewed concrete diaphragms at 0°, 15°, 30°, and 40°. The slabs were statically loaded through a wheel footprint at preselected locations until failure occurred. To analytically evaluate the nominal strength for these composite slab specimens, yield-line and punching-shear theories were applied to the crack patterns generated during the ultimate load tests. These computations and the observed mode of failure for the specimens indicated that punching shear governed the nominal strength of the slabs. The nominal strength of the slabs significantly exceeded the design load requirements.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Abendroth, R. E., Pratanata, H., and Singh, B. (1991). “Composite precast prestressed concrete bridge slabs.”Final Rep.; Iowa DOT Proj. HR-319, ISU-ERI-Ames-92076, Engineering Research Institute, Iowa State University, Ames, Iowa.
2.
Barker, J. M.(1975). “Research, application and experience with precast prestressed bridge deck panels.”PCI J., 20(6), 66–85.
3.
Barnoff, R. M., and Rainey, D. E. (1974). “Laboratory test of prestressed concrete deck planks and deck plank assemblies.”Res. Proj. No. 71-8; An Experimental Prestressed Concrete Bridge; Rep. No. 2. Pennsylvania Transportation Institute, Pennsylvania State University, University Park, Pa.
4.
Barnoff, R. M., Orndorff, J. A. Jr., Harbaugh, R. B. Jr., and Rainey, D. E.(1977). “Full scale test of a prestressed bridge with precast deck planks.”PCI J., 22(5), 66–83.
5.
Callis, E. G., Fagundo, F. E., and Hays, C. O. Jr. (1982). “Study of cracking of I-75 composite deck bridge over Peace River.”Res. Rep. No. U49F Vol. No. 1, Department of Civil Engineering, College of Engineering, University of Florida, Gainesville, Fla.
6.
Fang, I. K., Tsui, C. K. T., Burns, N. H., and Klingner, R. E.(1990). “Load capacity of isotropically reinforced, cast-in-place and precast panel bridge decks.”PCI J., 33(4), 104–113.
7.
Jones, H. L., and Furr, H. L. (1970). “Study of in-service bridges constructed with prestressed panel sub-decks.”Res. Rep. 145-1, Texas Transportation Institute, Texas A & M University, College Station, Tex.
8.
Kluge, R. W., and Sawyer, H. A.(1975). “Interacting pretensioned concrete form panels for bridge decks.”PCI J., 20(3), 34–61.
9.
“Precast prestressed concrete bridge deck panels.” (1987). PCI J ., 32(2), 26–45.
10.
Ross Bryan Associates, Inc.(1988). “Recommended practice for precast prestressed concrete composite bridge deck panels.”PCI J., 20(2), 67–109.
11.
Standard specifications for highway bridges. (1989). 14th Ed., American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
12.
“Tentative design and construction specifications for bridge deck panels.” (1978). PCI J ., 23(1), 32–39.
Information & Authors
Information
Published In
Copyright
Copyright © 1995 American Society of Civil Engineers.
History
Published online: Feb 1, 1995
Published in print: Feb 1995
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.