Theoretical and Experimental Evaluation of FRP Components and Systems
Publication: Journal of Structural Engineering
Volume 120, Issue 2
Abstract
Two bridge superstructural systems and two other floor systems are constructed and tested under concentric static loads using fiber reinforced plastic (FRP) shapes. Structural performance of individual FRP components is established through three‐ and four‐point bending tests. Structural efficiency of each system is analyzed in terms of joint efficiency, transverse load distribution, composite action between FRP components, and maximum deflections and stresses. Theoretical prediction of system performance is conducted by the orthotropic plate theory, finite‐element method, and a method to predict beam stiffnesses based on simplified classical lamination theory (CLT). The correlation between theoretical and experimental results is good and reveals that the simplified CLT can be effectively used in future designs. The bridge and floor systems tested herein had undergone deflections smaller or at the most equal to the allowable (L/1,000 and L/360, respectively) for loads larger than the corresponding allowable loads (72 kN and 3.8 kN, respectively).
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ballinger, C. A. (1990). “Structural FRP composites—civil engineering's material of the future?” Civ. Engrg., ASCE, 60(7), 63–65.
2.
Barbero, E. J. (1991). “Pultruded structural shapes: stress analysis and failure prediction.” Specialty Conf. on Advanced Composites in Civ. Engrg. Struct., ASCE, New York, N.Y., 194–204.
3.
Design guide. (1989). Creative Pultrusions Inc., Pleasantville, Pa.
4.
Doyle, J. R. (1991). “Behavior of bolt and adhesive connections in fiber reinforced members,” MSc thesis, West Virginia University, Morgantown, W.Va.
5.
GangaRao, H. V. S., Seifert, W., and Kevork, H. (1988). “Behavior and design of open steel grid decks for highway bridges.” Final Rep. for WVDOH; Vol. I, West Virginia Department of Highways, Morgantown, W. Va.
6.
GangaRao, H. V. S., and Raju, P. R. (1992). “Transverse wheel load distribution for deck‐stringer bridges.” Proc., 3rd NSF Workshop on Bridge Engrg. Res. in Progress, National Science Foundation (NSF) Washington, D.C.
7.
“Golf course bridge uses Pultex structural shapes.” (1990). News of Fiber Pultruded Struct., (Oct.), Pleasantville, Pa.
8.
Introduction to ANSYS: revision 4.4. (1989). Swanson Analysis Systems, Inc., Houston, Pa.
9.
Jones, R. M. (1975). Mechanics of composite materials. Hemisphere Publishing Co.
10.
Knowles, P. R. (1973). Composite steel and concrete construction. John Wiley & Sons, London, England.
11.
Leonard, L. (1990). “Rebuilding the infrastructure with advanced composites.” Advanced Composites, (May–Jun.), 43–47.
12.
McCormick, F. C. (1978). “Laboratory and field studies of a pedestrian bridge composed of glass reinforced plastics.” Transp. Res. Record 665, National Research Council, Washington, D.C., 99–107.
13.
McCormick, F. C. (1987). “Field study of a pedestrian bridge of reinforced plastic.” Transp. Res. Record 1118, National Research Council, Washington, D.C., 88–98.
14.
Meier, U. (1991). “Chapter 9: case histories.” Advanced composite materials with application to bridges. The Canadian Society for Civil Engineering, Montreal, Canada.
15.
Mongi, A. N. K. (1991). “Theoretical and experimental behavior of FRP floor systems,” MSc report, West Virginia University, Morgantown, W.Va.
16.
Sotiropoulos, S. N. (1991). “Static response of bridge superstructures made of fiber reinforced plastic,” MSc thesis, West Virginia University, Morgantown, W.Va.
17.
Sotiropoulos, S. N., GangaRao, H. V. S., and Barbero, E. (1991). “Static response of bridge superstructures made of fiber reinforced plastic.” Proc., Winter Annu. Meeting, American Society of Mechanical Engineers, New York, N.Y.
18.
Standard specifications for highway bridges. (1989). 14th Ed., American Association of State Highways and Transportation Officials (AASHTO), Washington, D.C.
19.
Timoshenko, S. P., and Goodier, J. N. (1982). Theory of elasticity, 3rd Ed., McGraw‐Hill Book Co., New York, N.Y.
20.
Timoshenko, S. P., Young, D. H., and Weaver, W. (1974). Vibration problems in engineering, 4th Ed., Wiley Book Co., New York, N.Y.
21.
Troitsky, M. S. (1987). Orthotropic bridges: theory and design, 2nd Ed., James F. Lincoln Arc Welding Foundation, Cleveland, Ohio, 15.1–15.16.
Information & Authors
Information
Published In
Copyright
Copyright © 1994 American Society of Civil Engineers.
History
Received: Jul 19, 1991
Published online: Feb 1, 1994
Published in print: Feb 1994
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.