Assessing Fitness for Purpose of Offshore Platforms. I: Analytical Methods and Inspections
This article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 120, Issue 12
Abstract
Existing structures, including offshore platforms, often do not meet the same standards as those mandated for new designs. It is also recognized by the engineering community that acceptance criteria for existing structures: (1) Should not necessarily be the same as those for new designs, and (2) should be dependent on the consequences of structural failure. Because of a large population of aging offshore platforms worldwide, reassessment of platforms to determine their fitness for purpose has gained considerable attention by the oil and gas industry and regulatory agencies in the United States and overseas. The reassessment process could be time‐consuming and costly because it requires many steps such as: gathering information on design and physical condition of the platform, modeling of all important damage found, structural evaluation of the platform, calculation of reliability indices, and determination of mitigation and repair schemes. Therefore, a reassessment process covers a large span of technical topics and could require more effort and expertise compared to a new design.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Banon, H. (1994). “Assessing fitness for purpose of offshore platforms II, risk management, maintenance, and repair.” J. Struct. Engrg., ASCE, 120(12), 3613–3633.
2.
Bea, R. G., Puskar, F. J., Smith, C., Spenser, J. (1988). “Development of AIM (assessment, inspection, maintenance) programs for fixed and mobile offshore platforms.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
3.
De, R. S., and Cornell, C. A. (1992). “Factors in structural system reliability.” Proc., 4th IFIP WG 7.5 Conf. on Reliability and Optim. of Struct. Sys., R. Rackwitz and P. Thoft‐Christensen, eds., Springer‐Verlag, Berlin, Germany, 159–169.
4.
Earl, C. P., and Teer, M. J. (1989). “A rational and economical approach to the calculation of K‐factors.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
5.
Ellinas, C. P. (1984). “Ultimate strength of damaged tubular bracing members.” J. Struct. Engrg., ASCE, 110(2), 245–259.
6.
“Guidance on methods for assessing the acceptability of flaws in fusion welded structures.” (1991). BS‐PD 6493, British Standards Institution, London, U.K.
7.
Hu, J. S., Tsiatas, G., and McGrath, J. E. (1991). “Optimal linearization of Morison‐type wave loading.” J. Engrg. Mech., ASCE, 117(7), 1537–1553.
8.
Hsu, T. M. (1994). “Strength of tubular members containing holes.” J. Offshore Mechanics and Arctic Engrg., ASME, 116(3), 154–162.
9.
Karamchandani, A. (1990). “Limitations of some of the approximate structural analysis methods that are used in structural system reliability.” Struct. Safety, 7, 115–127.
10.
Karamchandani, A., Dalane, J. I., and Bjerager, P. (1992). “System reliability approach to fatigue of structures.” J. Struct. Engrg., ASCE, 118(3), 684–700.
11.
Karamchandani, A., and Cornell, C. A. (1992). “An event‐to‐event strategy for nonlinear analysis of truss structures, I.” J. Struct. Engrg., ASCE, 118(4), 895–909.
12.
Karamchandani, A., and Cornell, C. A. (1992). “Reliability analysis of truss structures with multistate elements, II.” J. Struct. Engrg., ASCE, 118(4), 910–925.
13.
Karsan, D. I., and Kumar, A. (1990). “Fatigue failure paths for offshore platform inspection.” J. Struct. Engrg., ASCE, 116(6), 1679–1695.
14.
Kumar, A., and Karsan, D. I (1990). “Fatigue reliability of parallel systems.” J. Struct. Engrg., ASCE, 116(3), 719–729.
15.
Lloyd, J. R., and Clawson, W. C. (1983). “Reserve and residual strength of pile founded offshore platforms.” Proc., Symp. on the Role of Design, Inspection, and Redundancy in Marine Struct. Reliability, National Academic Press.
16.
Loh, J. T. (1990). “A unified design procedure for tubular members.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
17.
Loh, J. T., Kahlich, J. L., and Broekers, D. L. (1992). “Dented tubular steel members.” Exxon Production Research Company Report, Exxon Production Research Co., Houston, Tex.
18.
Lutes, L. D., Corazao, M., Hu, S. J., and Zimmerman, J. J. (1984). “Stochastic fatigue damage accumulation.” J. Struct. Engrg., ASCE, 110(11), 2585–2601.
19.
Ma, S. Y., Tebbett, I. E. (1988). “New data on the ultimate strength of tubular welded K‐Joints under moment loads.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
20.
Madsen, H. O., Skjong, R. K., Tallin, A. G., and Kirkemo, F. (1987). “Probabilistic fatigue crack growth analysis of offshore structures, with reliability updating through inspection.” Proc., The Marine Struct. Reliability Symp. Society of Naval Architects and Marine Engineers, Jersey City, N.J.
21.
Makino, Y., Kurobane, Y., and Yamamoto, N. (1986). “Behavior of tubular T‐ and K‐Joints under combined loads.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
22.
Malhotra, A. K., and Penzien, J. (1970). “Nondeterministic analysis of offshore structures.” J. Engrg. Mech., ASCE, 96(6), 985–1003.
23.
McClelland, B., and Reifel, M. D., eds. (1986). Planning and design of offshore platforms. Van Nostrand Reinhold Co., New York, N.Y.
24.
Pike, P. J., and Grenda, K. G. (1987). “A load‐shedding algorithm for buckled compression braces.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
25.
“Recommended practice for planning, designing and constructing fixed offshore platforms.” (1993a). API RP2A. 20th Ed., American Petroleum Institute, Washington, D.C.
26.
“Recommended practice for planning, designing and constructing fixed offshore platforms—load and resistance factor design.” (1993b). API RP2A‐LRFD. 1st Ed., American Petroleum Institute, Washington, D.C.
27.
Sanders, D. H., and Yura, J. A. (1987). “Strength of double‐tee tubular joints in tension.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
28.
Soreide, T. H., Amdahl, J., Granli, T., and Astrud, O. C. (1986). “Collapse analysis of framed offshore structures.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
29.
Stewart, G., and van de Graaf, J. W. (1990). “A methodology for platform collapse analysis based on linear superposition.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Houston, Tex.
30.
Stewart, G. (1992). “Non‐linear structural dynamics by the pseudo‐force influence method, part i: theoretical considerations.” Proc., 2nd Int. Offshore and Polar Engrg. Conf., 257–271.
31.
Taby, J., and Moan, T. (1987). “Ultimate behavior of circular tubular members with large initial imperfections.” Proc., Annu. Tech. Session, Struct. Stability Research Council, Stability Research Council, 79–104.
32.
Taby, J., and Moan, T. (1985). “Collapse and residual strength of damaged tubular members.” Proc., 4th Int. Conf. on Behavior of Offshore Struct., 395–408.
33.
Titus, P. G., and Banon, H. (1988). “Reserve strength analyses of offshore platforms.” Proc., 7th Offshore Southeast Asia Conf., Society of Petroleum Engineering, Richardson, Tex.
34.
Wang, J., and Lutes, L. D. (1991). “Nonlinear and non‐gaussian aspects of Morison equation induced fatigue damage.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
35.
Wen, Y. K. (1988). “Environmental event combination criteria, phase i, risk analysis.” Res. Rep. PRAC 87‐20, American Petroleum Institute, Washington D.C.
36.
Wen, Y. K., and Banon, H. (1991). “Development of environmental combination design criteria for fixed platforms in the Gulf of Mexico.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
37.
Wirsching, P. H. (1983). “Probability based fatigue design criteria for offshore structures.” Final Rep., PRAC Project 81‐15, American Petroleum Institute, Washington D.C.
38.
Yura, J. A., Zettlemoyer, N., and Edwards, I. F. (1980). “Ultimate capacity equations for tubular joints.” Proc., Offshore Technol. Conf., Society of Petroleum Engineering, Richardson, Tex.
39.
Zettlemoyer, N. (1988). “Developments in ultimate strength technology for simple tubular joints.” Offshore Tubular Joints Conf., Steel Construction Institute, Surrey, U.K.
Information & Authors
Information
Published In
Copyright
Copyright © 1994 American Society of Civil Engineers.
History
Received: Mar 10, 1993
Published online: Dec 1, 1994
Published in print: Dec 1994
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.