Web‐Flange Interaction in Cold‐Formed Steel Z‐Section Columns
Publication: Journal of Structural Engineering
Volume 119, Issue 9
Abstract
In the American Iron and Steel Institute (AISI) specification for the design of cold‐formed steel structural members, the web of cold‐formed steel sections under direct compression is generally considered to be fully stiffened and a buckling coefficient of 4.0 is used. This, however, may not be true if the flanges of the sections cannot provide sufficient restraint to the web. Also, if the web element is unstable, distortional failure of the flange/lip component may limit the ultimate capacity of these sections with very little postbuckling strength being realized. This paper presents results from an experimental program involving 85 Z‐section columns tested under uniform compression. The test parameters included the length of specimens, the width of the flanges and the width of the lip stiffeners which were located transversely to the flanges. The experimental results indicate that the current AISI specification overestimates the capacity of Z‐sections subject to web buckling by as much as 59%. A simple theoretical model is also presented in this paper for computing the ultimate compressive resistance of cold‐formed Z‐sections.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Charnvarnichborikarn, P., and Polyzois, D. (1990). “Experimental and analytical investigation of cold‐formed Z‐section steel members in compression.” Research Report No. 1990‐2, Dept. of Civ. Engrg., Univ. of Manitoba, Winnipeg, Manitoba.
2.
Cohen, J. M., and Pekoz, T. (1986). “Local buckling of plate elements.” Proc. Sessions of Struct. Congress, ASCE, 235–244.
3.
Desmond, T. P. (1978). “The behaviour and strength of thin‐walled compression elements with longitudinal stiffeners.” Research Report No. 369, Dept. of Struct. Engrg., Cornell Univ., Ithaca, N.Y.
4.
Lau, S. C. W., and Hancock, G. T. (1987). “Distortional buckling formulas for channel columns.” J. Struct. Engrg., ASCE, 13(5), 1063–1078.
5.
Le, Q. P., Polyzois, D., and Charnvarnichborikarn, P. (1990). “Behaviour of cold‐formed steel members in compression.” Research Report No. 1990‐1, Dept. of Civ. Engrg., Univ. of Manitoba, Winnipeg, Manitoba.
6.
Mulligan, G. P. (1983). “The influence of local buckling on the structural behaviour of singly‐symmetric cold‐formed steel columns,” PhD thesis, Cornell University, Ithaca, N.Y.
7.
Rosner, C. N., Polyzois, D., and Charnvarnichborikarn, P. (1989). “An experimental investigation on the behaviour of cold‐formed steel columns.” Research Report No. 1989‐1, Dept. of Civ. Engrg., Univ. of Manitoba, Winnipeg, Manitoba.
8.
“Specification for the design of cold‐formed steel structural members.” (1986). Cold‐formed steel design manual, Am. Iron and Steel Inst., Washington, D.C.
9.
“Specification for the design of cold‐formed steel structural members.” (1989). Cold‐formed steel design manual, Am. Iron and Steel Inst., Washington, D.C.
10.
“Standard methods for tension testing of metallic materials.” ASTM E 8M‐85, (1985). ASTM, Philadelphia, Pa.
11.
“Standard specification for steel, sheet and strip, high‐strength, low‐alloy, columbium or vanadium, or both, hot‐rolled and cold‐rolled.” (1991). ASTM A607‐90A, ASTM, Philadelphia, Pa.
12.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability. McGraw‐Hill Book Co., Inc., New York, N.Y.
13.
Vlasov, V. Z. (1961). Thin walled elastic beams. 2nd Ed., Israel Program for Scientific Translations, Jerusalem, Israel.
14.
Weng, C. C., and Pekoz, T. (1990). “Compression tests of cold‐formed steel columns.” J. Struct. Engrg., ASCE, 116(5), 1230–1246.
Information & Authors
Information
Published In
Copyright
Copyright © 1993 American Society of Civil Engineers.
History
Received: May 5, 1992
Published online: Sep 1, 1993
Published in print: Sep 1993
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.