Serviceability Design in LRFD for Wood
Publication: Journal of Structural Engineering
Volume 119, Issue 12
Abstract
The phenomenon of creep causes the deflection of a wood beam under sustained loading to increase throughout time. Current design codes include provisions to account for the time‐dependent deflections of wood members in bending, but these guidelines have been based, to a large extent, on past performance and engineering judgment only. Previous reliability studies for wood have not explicitly considered creep effects, and consequently, questions as to the true limit‐state exceedence probabilities associated with serviceability design procedures remain unanswered. In this paper, the effect of creep deformations on the reliability of single dimension‐lumber wood beams is examined. A stochastic viscoelastic stress‐strain relationship is used to model the time‐dependent behavior of wood, and stochastic pulse process models are used to account for the temporal variability of the loads. Reliability levels associated with current serviceability design procedures are then determined, and resistance factors that include creep effects are suggested for use in a checking equation for load and resistance factor design.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Chalk, P., and Corotis, R. B. (1980). “A probability model for design live loads.” J. Struct. Div., ASCE, 106(10), 2017–2033.
2.
Corotis, R. B., and Doshi, V. A. (1977). “Probability models for live‐load survey results.” J. Struct. Div., ASCE, 103(6), 1257–1274.
3.
Ellingwood, B., and Culver, C. G. (1977). “Analysis of live loads in office buildings.” J. Struct. Div., ASCE, 103(8), 1551–1560.
4.
Ellingwood, B., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American National Standard A58.” National Bureau Special Publication No. 577, Nat. Bureau of Standards, Washington, D.C.
5.
Ellingwood, B., and Rosowsky, D. V. (1991). “Duration of load effects in LRFD for wood construction.” J. Struct. Engrg., ASCE, 117(2), 584–599.
6.
Flugge, W. (1975). Viscoelasticity, 2nd Ed., Springer‐Verlag, New York, N.Y.
7.
Folz, B., and Foschi, R. O. (1989). “Reliability‐based design of wood structural systems.” J. Struct. Engrg., ASCE, 115(7), 1666–1680.
8.
Foschi, R. O., Folz, B. R., and Yao, F. Z. (1989). “Reliability‐based design of wood structures.” Struct. Res. Series Report No. 34, Dept. of Civ. Engrg., Univ. of British Columbia, Vancouver, British Columbia.
9.
Fridley, K. J. (1992). “Designing for creep in wood structures.” Forest Products J., 42(3), 23–28.
10.
Fridley, K. J., Tang, R. C., and Soltis, L. A. (1992a). “Creep behavior model for structural lumber.” J. Struct. Engrg., ASCE, 118(8), 2261–2277.
11.
Fridley, K. J., Tang, R. C., and Soltis, L. A. (1992b). “Hygrothermal effects on mechanical properties of lumber.” J. Struct. Engrg., ASCE, 118(2), 567–581.
12.
Galambos, T. V., and Ellingwood, B. (1986). “Serviceability limit states: Deflection.” J. Struct. Engrg., ASCE, 112(1), 67–84.
13.
Gerhards, C. C. (1985). “Time‐dependent bending deflections of Douglas‐fir 2 by 4's.” Forest Products J., 35(4), 18–26.
14.
Green, D. W., and Evans, J. W. (1987). Mechanical properties of visually graded lumber: Volume 1, a summary. U.S. Dept. of Agric., Forest Service, Forest Products Laboratory, Madison, Wisc.
15.
Hendrickson, E. M., Ellingwood, V., and Murphy, J. (1987). “Limit state probabilities for wood structural members.” J. Struct. Engrg., ASCE, 113(1), 88–106.
16.
Hoyle, R. J., Griffith, M. C., and Itani, R. Y. (1985). “Primary creep in Douglas‐fir beams of commercial size and quality.” Wood and Fiber Sci., 17(3), 300–314.
17.
Hoyle, R. J., Itani, R. Y., and Eckard, J. J. (1986). “Creep of Douglas‐fir beams due to cyclic humidity fluctuations.” Wood and Fiber Sci., 18(3), 468–477.
18.
Load and resistance factor design specifications for engineered wood construction. (draft). (1991). New York, N.Y., Jul.
19.
McGuire, R. K., and Cornell, C. A. (1974). “Live load effects in office buildings.” J. Struct. Div., ASCE, 100(7), 1351–1366.
20.
“Minimum design loads for buildings and other structures.” (1990). (ASCE 7‐88), ASCE, New York, N.Y.
21.
National design specifications for wood construction. (1991). Nat. Forest Products Assoc., Washington, D. C.
22.
Philpot, T. A., and Rosowsky, D. V. (1992). “Statistics for light‐occupancy live load process modeling.” Struct. Engrg. Report No. CE‐STR‐92‐3, Purdue Univ., West Lafayette, Ind.
23.
Rosowsky, D. V., and Ellingwood, B. R. (1990). “Stochastic damage accumulation and probabilistic codified design for wood.” Civ. Engrg. Report No. 1990‐02‐02, Johns Hopkins Univ., Baltimore, Md.
24.
Rosowsky, D., and Ellingwood, B. (1991). “System reliability and load‐sharing effects in light‐frame wood construction.” J. Struct. Engrg., ASCE, 117(4), 1096–1114.
25.
Rosowsky, D. V., and Ellingwood, B. R. (1992). “Limit‐state interactions in reliability‐based design for wood structures.” J. Struct. Engrg., ASCE, 118(3), 813–827.
26.
Senft, J. F., and Suddarth, S. K. (1971). “An analysis of creep‐inducing stress in sitka spruce.” Wood and Fiber, 2(4), 321–327.
27.
Uniform building code. (1985). Int. Conf. of Bldg. Officials, Whittier, Calif.
Information & Authors
Information
Published In
Copyright
Copyright © 1993 American Society of Civil Engineers.
History
Received: Jan 25, 1993
Published online: Dec 1, 1993
Published in print: Dec 1993
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.