Modeling Slab Contribution in Frame Connections
Publication: Journal of Structural Engineering
Volume 118, Issue 9
Abstract
Contribution of monolithic floor slabs to the negative (hogging) flexural resistance of beams in reinforced concrete frames may inadvertently affect the hierarchy of failure unless it is considered during the design. A qualitative model simulating participation of slabs to the behavior of beams is developed by establishing the kinematic relations between beam deformations and the state of strain in the slab. The slab is idealized as a membrane element by using a network of rigid links and flexible springs connecting the slab bars to the supporting beams. Support displacements of the rigid links, such as reinforcement slip, twist, weak axis rotation, and elongation of the transverse beams are considered. Reasonable correlation of test data from interior and exterior slab‐beam‐column subassemblies is possible. The computed responses were most sensitive to the assumed length of plastic hinge, and to a lesser degree, to the distribution of longitudinal strains within the plastic hinge. In the range of low deformations, results are somewhat sensitive to the assumed initial transverse beam stiffness. Available expressions for establishing length of plastic hinge seem sufficient.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bas, A. (1990). “Behavior of reinforced concrete beam‐column connections with floor slabs under bi‐directional loads,” Master of Sci. thesis, Univ. of Toronto, Toronto, Canada.
2.
Chern, S. P., and Shahrooz, B. M. (1990). “An analytical model for simulating the contribution of floor slab in slab‐beam‐column systems,” Master of Sci. thesis, Univ. of Cincinnati, Cincinnati, Ohio.
3.
“Commentary on building code requirements for reinforced concrete.” (1989). ACI 318‐89/318R‐89, American Concr. Inst., Detroit, Mich.
4.
Corley, W. G. (1966). “Rotational capacity of reinforced concrete beams.” J. Struct. Div., ASCE, 92(5), 121–146.
5.
“Design of concrete structures for buildings.” (1984). CAN3‐A23.3‐M84, Canadian Standards Association, Rexdale, Ontario, Canada.
6.
Durrani, A. J., and Wight, J. K. (1982). “Experimental and analytical study of internal beam to column connections subjected to reversed cyclic loading.” Report No. UMEE 82R3, Univ. of Michigan, Ann Arbor, Mich.
7.
French, C. W., and Boroojerdi, A. (1989). “Contribution of RC floor slabs in resisting lateral loads.” J. Struct. Engrg., ASCE, 115(1), 1–18.
8.
Jirsa, J. O., Lutz, L. A., and Gergely, P. (1979). “Rationale for suggested development, splice, and standard hook provisions for deformed bars in tension.” Concr. Int., 1(7), 47–61.
9.
Joglekar, M. R., Murray, P. A., Jirsa, J. O., and Klinger, R. E. (1984). “Full scale tests of beam‐column joints.” Earthquake effects on reinforced concrete structures, U.S.‐Japan Res., American Concrete Institute, Detroit, Mich.
10.
Kiureghian, S. (1983). “Hysteretic behavior of R/C exterior beam‐column‐slab subassembly.” CE299 Report, Univ. of California at Berkeley, Berkeley, Calif.
11.
Kurose, Y., Guimaraes, G. N. Liu, Z., Krieger, M. E., and Jirsa, J. O. (1988). “Study of R.C. beam‐column joints under uniaxial and biaxial loading.” Report No. PMFSEL 88‐2, Univ. of Texas at Austin, Austin, Texas.
12.
Lampert, P. (1973). “Post‐cracking stiffness of reinforced concrete beams in torsion and bending.” Analysis of structural systems for torsion. ACI special publication SP‐35.
13.
Mattock, A. H. (1967). Discussion of“Rotational capacity of reinforced concrete beams,” by W. G. Corley. J. Struct. Div., ASCE, 93(2), 519–522.
14.
“Model code for seismic design of concrete structures.” (1983). Bulletin d'Information No. 160, Comité Euro‐Internationàl du Béton, Paris, France.
15.
Orangun, C. O., Jirsa, J. O., and Breen, J. E. (1977). “A reevaluation of test data on development lengths and splices.” ACI J., 114–122.
16.
Otani, S., Kabeyasawa, T., Shiohara, H., and Aoyama, H. (1984). “Analysis of the full‐scale seven‐story reinforced concrete test structure.” Earthquake effects on reinforced concrete structures, U.S.‐Japan Research.
17.
Pantazopoulou, S. J., Moehle, J. P., and Shahrooz, B. M. (1988). “A simple model for the effect of slabs on beam strength.” J. Struct. Engrg., ASCE, 114(7), 1507–1523.
18.
Park, R., and Paulay, T. (1975). Reinforced concrete structures. John Wiley and Sons, New York, N.Y.
19.
Qi, X., and Pantazopoulou, S. J. (1991). “Response of RC frames under lateral loads.” J. Struct. Engrg., ASCE, 117(4), 1167–1188.
20.
“Recommendations for design of beam‐column joints in monolithic reinforced concrete structures (ACI 352R‐85).” (1985). ACI J., 73(8), 266–283.
21.
“U.S.‐Japan research: Seismic design implications.” J. Struct. Engrg., ASCE, 114(9), 2000–2016.
22.
Zerbe, H. E., and Durrani, A. J. (1985). “Effect of slab on the behavior of exterior beam to column connections.” Report No. 30, Houston, Texas.
23.
Zerbe, H. E., and Durrani, A. J. (1990). “Seismic response of connections in indeterminate R/C frame subassemblies.” Report No. 40, Rice Univ., Houston, Texas.
Information & Authors
Information
Published In
Copyright
Copyright © 1992 ASCE.
History
Published online: Sep 1, 1992
Published in print: Sep 1992
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.