Validation of Design Recommendations for Integral‐Abutment Piles
Publication: Journal of Structural Engineering
Volume 117, Issue 7
Abstract
Because integral‐abutment bridges decrease the initial and maintenance costs of bridges, they provide an attractive alternative for bridge designers. The objective of this project is to develop rational and experimentally verified design recommendations for piles in these bridges. Field testing consists of instrumenting two bridges in Iowa to monitor air and bridge temperatures, bridge displacements, and pile strains. Core samples are also collected to determine coefficients of thermal expansion for the two bridges. Design values for the coefficient of thermal expansion of concrete and revised temperature ranges for the deck and girders of steel and concrete bridges are recommended. A girder extension model is developed to predict the longitudinal bridge displacements caused by changing bridge temperatures. The pile is idealized as an equivalent cantilever. The frame model better predicts both the longitudinal displacement and weak‐axis pile strains. A lateral frame model is presented to predict the lateral motion of skewed bridges. Two alternatives for the pile design are reviewed: the first alternative, the more conservative, includes thermally induced stresses; the second neglects thermally induced stresses but allows for inelastic redistribution of forces.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Abendroth, R. E., and Greimann, L. F. (1989). “A rational design approach for integral abutment bridge piles.” Transp. Res. Record, 1233, 12–23.
2.
Abendroth, R. E., Greimann, L. F., and Ebner, P. B. (1989). “Abutment pile design for jointless bridges.” J. Struct. Engrg., ASCE, 115(11), 2914–2929.
3.
British code BS 5400. (1978). Part 2, British Standards Inst., London, England.
4.
Churchward, A., and Sokal, Y. J. (1981). “Prediction of temperatures in concrete bridges.” J. Struct. Div., ASCE, 107(11), 2163–2176.
5.
Emanuel, J. H., and Hulsey, J. L. (1977). “Prediction of the thermal coefficient of expansion of concrete.” J. Am. Concr. Inst., 74(4), 149–155.
6.
Emanuel, J. H., and Hulsey, J. L. (1978). “Temperature distributions in composite bridges.” J. Struct. Div., ASCE, 104(1), 65–78.
7.
Girton, D. D., Hawkinson, T. R., and Greimann, L. F. (1989). “Validation of design recommendations for integral abutment piles.” Iowa DOT Project HR‐292, Iowa State Univ.‐Engrg. Res. Inst., Ames, Iowa.
8.
Greimann, L. F., Abendroth, R. E., Johnson, D. E., and Ebner, P. B. (1987). “Pile design and tests for integral abutment bridges.” Final Report, Iowa DOT Project HR‐273, Iowa State Univ.‐Engrg. Res. Inst., Ames, Iowa.
9.
Greimann, L. F., Wolde‐Tinsae, A. M., and Yang, P.‐S. (1983). “Skewed bridges with internal abutments.” Transp. Res. Record, 903, 64–72.
10.
Greimann, L. F., Yang, P.‐S., Edmunds, S. K., and Wolde‐Tinsae, A. M. (1984). “Design of piles for integral abutment bridges.” Final Report, Iowa DOT Project HR‐252, Iowa State Univ.‐Engrg. Res. Inst., Ames, Iowa.
11.
Greimann, L. F., Yang, P.‐S., and Wolde‐Tinsae, A. M. (1986). “Nonlinear analysis of integral abutment bridges.” J. Struct. Engrg., ASCE, 112(10), 2263–2280.
12.
Ho, D., and Liu, C.‐H. (1989). “Extreme thermal loadings in highway bridges.” J. Struct. Engrg., ASCE, 115(7), 1681–1696.
13.
Imbsen, R. A., Vandershaf, D. E., Schamber, R. A., and Nutt, R. V. (1985). “Thermal effects in concrete bridge superstructures.” National Cooperative Highway Research Program Report 276, Transp. Res. Board, Nat. Res. Council, Washington, D.C.
14.
“Integral no‐joint structures and required provisions for movement.” (1980). T5140.13, U.S. Dept. of Transp., Federal Highway Admin.
15.
Kennedy, J. B., and Soliman, M. H. (1987). “Temperature distribution in composite bridges.” J. Struct. Engrg., ASCE, 113(3), 475–482.
16.
Maragakis, E. A. and Siddharthan, R. (1989). “Estimation of inelastic longitudinal abutment stiffness of bridges.” J. Struct. Engrg., ASCE, 115(9), 2382–2399.
17.
Ontario highway bridge design code and commentary. (1983). Ontario Ministry of Transp. and Communications, Toronto, Ontario, Canada.
18.
Reynolds, J. C., and Emanuel, J. H. (1974). “Thermal stresses and movements in bridges.” J. Struct. Div., ASCE, 100(1), 63–78.
19.
Standard specifications for highway bridges. (1983). 13th Ed., Amer. Assoc. of State Highway and Transp. Officials, Washington, D.C.
20.
Wolde‐Tinsae, A. M., Greimann, L. F., and Johnson, B. (1983). “Performance of integral bridge abutments.” IABSE Proc. P‐58/53, International Association for Bridge and Structural Engineering, 17–34.
Information & Authors
Information
Published In
Copyright
Copyright © 1991 ASCE.
History
Published online: Jul 1, 1991
Published in print: Jul 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.