Statistical Analysis of Imperfections in Stiffened Cylinders
Publication: Journal of Structural Engineering
Volume 117, Issue 7
Abstract
Despite several recent experimental and analytical programs on shell buckling, there is a lack of studies examining the characteristics of imperfection patterns produced by manufacturing. As a result, differing conclusions can be reached in strength assessment and in evaluating code recommendations, depending on imperfection‐modeling assumptions. A number of small‐scale stringer‐stiffened cylinders, all manufactured by the same method, were tested at Imperial College, London, England. Prior to loading, these models were carefully measured to record their initial imperfections. Data‐reduction techniques were subsequently used to obtain Fourier‐series representations of these surfaces. The purpose of this paper is to present the results of a detailed statistical analysis carried out on the Fourier coefficients. Both univariate and correlation statistics are presented for the variables characterizing the imperfection modes. In addition, the fitting of probability distributions is discussed and relevant parameters are presented for the dominant modes. The results show that because of the common manufacturing process several trends exist in the imperfection patterns. Thus, guidelines are developed that improve imperfection‐modeling assumptions in bucking‐strength analyses.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Agelidis, N. (1984). “Collapse of stringer stiffened cylinders,” thesis presented to the University of London, at London, England, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
2.
Agelidis, N., Harding, J. E., and Dowling, P. J. (1982). “Buckling tests on stringer stiffened cylinder models subject to load combinations.” Det norske Veritas Report No. 82‐0298.
3.
Arbocz, J. (1981). “Past, present and future of shell stability analysis.” Report LR‐320, Delft Univ. of Technology, Delft, the Netherlands.
4.
Arbocz, J. (1983). “Shell stability analysis: Theory and practice.” Collapse: The buckling of structures in theory and in practice, J. M. T. Thompson and G. W. Hunt, eds., Cambridge University Press, Cambridge, England, 43–74.
5.
Arbocz, J., and Babcock, C. D. (1976). “Prediction of buckling loads based on experimentally measured imperfections.” Buckling of structures. B. Budiansky, ed., Springer‐Verlag, Berlin, Germany, 291–311.
6.
BMDP Statistical Software. (1983). W. J. Dixon, chf. ed., University of California Press, Berkeley, Calif.
7.
BS 5500: Specification for unified fusion welded pressure vessels. British Standards Inst., London, England.
8.
Buckling of steel shells: European recommendations. (1988). European Convention for Constructural Steelwork, Brussels, Belgium.
9.
“Buckling strength analysis of mobile offshore units.” (1987). Classification Note 30.1, Det norske Veritas, Oslo, Norway.
10.
Chryssanthopoulos, M., Baker, M. J., and Dowling, P. J. (1987). “Small‐scale stringer‐stiffened cylinder models: Imperfection data analysis.” CESLIC Report SS3, Imperial College, London, England.
11.
Chryssanthopoulos, M., Baker, M. J., and Dowling, P. J. (1991). “Imperfection modeling for buckling analysis of stiffened cylinders.” J. Struct. Engrg., ASCE, 117(7), 1998–2017.
12.
Croll, J. G. A. (1983). “Elasto‐plastic buckling of pressure and axial loaded cylinders.” Proc. Inst. of Civ. Engrs., 73(Part 2), 633–652.
13.
Dowling, P. J., Harding, J. E., Fahy, W., and Agelidis, N. (1981). “Report on the testing of large and small‐scale stiffened shells under axial compression.” CESLIC Report SSI, Imperial College, London, England.
14.
Dwight, J. B. (1982). “Imperfection levels in large stiffened tubulars.” Buckling of shells in offshore structures. J. E. Harding, P. J. Dowling, and N. Agelidis, eds., Granada, London, England, 393–412.
15.
Harding, J. E. (1978). “The elasto‐plastic analysis of imperfect cylinders.” Proc., Inst. of Civ. Engrs., 65(Part 2), 875–892.
16.
Harding, J. E. (1985). “The interaction of imperfection wavelength and buckling mode in plated structures.” Ingenieurs et Architectes Suisses, 9–11.
17.
Harding, J. E., and Dowling, P. J. (1981). “Correlation between experimental and analytical results for the buckling of ring‐stiffened shells.” Integrity of offshore structures, D. Faulkner, M. J. Cowling, and P. A. Frieze, eds., Applied Science Publishers, London, England, 473–491.
18.
Kendrick, S. B. (1977). “Shape imperfections in cylinders and spheres: Their importance in design and method of measurement.” J. of Strain Analysis, 12(2), 117–122.
19.
Richards, D. M. (1982). “Shell buckling research and design appraisal procedures.” Buckling of shells in offshore structures, J. E. Harding, P. J. Dowling, and N. Agelidis, eds., Granada, London, England, 109–135.
20.
“Rules for the design, construction and inspection of offshore structures.” (1977). Appendix C, Det norske Veritas, Oslo, Norway.
21.
Scott, N. D., Harding, J. E., and Dowling, P. J. (1987). “Fabrication of small‐scale stiffened cylindrical shells.” J. Strain Analysis, 22(2), 97–106.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 117 • Issue 7 • July 1991
Pages: 1979 - 1997
Copyright
Copyright © 1991 ASCE.
History
Published online: Jul 1, 1991
Published in print: Jul 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.