Cold‐Bending of Thick High‐Strength Steel Plates
Publication: Journal of Structural Engineering
Volume 116, Issue 1
Abstract
The cold‐bending behavior of thick high‐strength steel plates is studied. Fifteen 1‐in. (25.4‐mm) and three 1.5‐in. (38.1‐mm) thick steel plates are cold‐bent to angles up to 90°, with bend radii of 1.5, 2.5, 3.5, and 5.5 in. Quantities measured include maximum surface strain, load‐displacement relationship, degree of springback, and residual stresses produced by the cold‐bending. Selected equations for predicting maximum surface strain and degree of springback are reviewed, and the values predicted by these equations are compared to test results. The results of the residual stress measurements are presented in a companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Alexander, J. M. (1959). “Analysis of the plastic bending of wide plate.” Proc. Inst. of Mech. Engrs., 173(1), London, U.K., 73–84.
2.
Botros, B. M. (1967). “Springback in sheet metal forming after bending.” ASME 67‐WA/PROD‐17, Winter Annual Mech. and Engrg. Systems Exposition, Nov., Pittsburg, Pa., 1–9.
3.
Cook, N. H. (1966). Manufacturing analysis. Addison‐Wesley Co., 112–115.
4.
Crandall, S. H. (1957). Discussion of “The Springback of Metal.” by F. J. Gardiner, Trans. ASME, 79, Jan., 7–9.
5.
Gardiner, F. J. (1957). “The springback of metal.” Trans. ASME, 79, Jan., 1–7.
6.
Johnson, W., and Mellor, P. B. (1980). Engineering plasticity. Van Nostrand Reinhold, New York, N.Y.
7.
Kervick, R. J., and Springborn, P. K. (1966). “Cold‐bending and forming tube and other sections.” ASME, 9–18.
8.
Sachs, G., and Lubahn, J. D. (1944). “Effect of non‐uniform stresses and strains.” NCRD No. M382, Office of Scientific Res. and Development.
9.
Sachs, G., and Lubahn, J. D. (1945). “Experimental strain analysis of bent rectangular shapes.” NCRD No. M616, Office of Scientific Res. and Development.
10.
Sangdahl, G. S., Aul, E. L., and Sachs, G. (1948). “An investigation of the stress and strain states occurring in bending rectangular bars.” SESA, 6(1), 1–18.
11.
Schroeder, W. (1943). “Mechanics of sheet metal bending.” Trans. ASME, 65, 817–827.
12.
Toth, R. P. (1983). “The search for a high elongation strain gage system.” Report SAND 83‐0549, Sandia Nat. Lab., Albuquerque, N.M.
13.
Weng, C. C., and White, R. N. (1984). “Cold‐bending of thick steel plates at low R/t ratios.” Report No. 84‐11, Dept. of Struct. Engrg., Cornell Univ., Ithaca, N.Y.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Jan 1, 1990
Published in print: Jan 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.