Fatigue Behaviour of Composite Metal Deck Slabs
Publication: Journal of Structural Engineering
Volume 115, Issue 1
Abstract
An experimental research program based on a proposed approach to fatigue testing that does not require a traditional stress versus cycles relationship was conducted to evaluate the behavior of composite metal deck slabs subjected to transverse cyclic loads. The magnitude of the maximum dynamic test load, obtained from progressively increasing cyclic load tests, was established as a percentage of the allowable static design load, evaluated from a linear regression study of companion statically loaded specimens. Periodically during the cyclic loading, static load tests revealed an increase in permanent deflections as the numbers of load cycles increased. At the completion of the fatigue testing, a static strength test showed that a shear‐bond failure occurred for the cyclically loaded specimens. This mode of failure was the same as for the companion statically loaded specimens. In general, the magnitiude of the applied load causing failure was reduced by the cyclic loading. A predicted, shear‐bond, fatigue strength expression applicable to the particular composite metal deck involved is presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Abdel‐Sayed, G., Temple, M. C., and Madugula, K. S. (1974). “Response of composite slabs to dynamic loads.” Can. J. Civ. Engrg., 1(1), 62–70.
2.
ASCE Standard. (1984). Specifications for the Design and Construction of Composite Slabs and Commentary on Specifications for the Design and Construction of Composite Slabs. ASCE Technical Council of Codes and Standards Division, New York, N.Y.
3.
Luttrell, L. D., and Davison, J. H. (1973). “Composite slabs with steel deck panels.” Proc., Second Specialty Conference on Cold‐Formed Steel Structures, University of Missouri, Rolla, October, 573–603.
4.
Luttrell, L. D., and Prasannan, S. (1984). “Strength formulations for composite slabs.” Proc., Seventh International Specialty Conference on Cold‐Formed Steel Structures, University of Missouri‐Rolla, November, 307–326.
5.
Mouw, K. W. (1969). “Fatigue testing of light gage metal forms.” Special Report ERI‐348 Project‐741, Engineering Research Institute, Iowa State University, Ames, Iowa.
6.
Porter, M. L., and Ekberg, C. E., Jr. (1976). “Design recommendations for steel deck floor slabs.” J. Struct. Div., ASCE, 102(11), 2121–2136.
7.
Porter, M. L., and Ekberg, C. E., Jr. (1977). “Behavior of steel‐deck‐reinforced slabs.” J. Struct. Div., ASCE, 103(3), 663–677.
8.
Porter, M. L., et al. (1976). “Shear‐bond analysis of steel‐deck‐reinforced slabs.” J. Struct. Div., ASCE, 102(12), 2255–2268.
9.
Schuster, R. M. (1977). “Composite steel‐deck concrete floor systems.” J. Struct. Div., ASCE, 102(5), 899–917.
10.
Schuster, R. M., and Ling, W. C. (1980). “Mechanical interlocking capacity of composite slabs.” Proc., Fifth International Specialty Conference on Cold‐Formed Steel Structures, St. Louis, Missouri, November, 387–407.
11.
Schuster, R. M., and Suleiman, R. E. (1986). “Composite slabs subjected to repeated point loading.” Proc., Eighth International Specialty Conference on Cold‐Formed Steel Structures, University of Missouri‐Rolla, November, 453–485.
12.
Temple, M. C., and Abdel‐Sayed, G. (1979). “Fatigue experiments on composite slab floors.” J. Struct. Div., ASCE, 105(7), 1435–1443.
Information & Authors
Information
Published In
Copyright
Copyright © 1989 ASCE.
History
Published online: Jan 1, 1989
Published in print: Jan 1989
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.