Statistical Analysis of Tubular R/C Sections
Publication: Journal of Structural Engineering
Volume 114, Issue 4
Abstract
A statistical analysis of the moment capacity of a tubular reinforced‐concrete (R/C) section is performed. The moment capacity of the cross section is estimated utilizing a second‐order stress‐strain relationship for concrete. This study followed the American Concrete Institute (ACI) code in assuming that the ultimate moment‐capacity limit state is reached when the concrete strain attains a value of 0.003. For the serviceability limit state, it is assumed that the sections fails to perform satisfactorily when the first steel reinforcement bar yields. The capacity of a cross section may vary due to variabilities in section properties, material strengths, and uncertainty associated with the prediction model. A systematic analysis of the propagation of uncertainties associated with these factors and their contribution to the overall uncertainty in the moment capacity is obtained based on the first‐order secondmoment (FOSM) and Monte Carlo simulation techniques. A closed‐form expression is derived for the uncertainty in the moment capacity following the FOSM approach. The FOSM approach provides results that are in good agreement with the Monte Carlo simulation. The results of a parametric study suggest that, for the example chimney, the coefficient of variation of the moment capacity is insensitive to the variation in the steel ratio. The analysis presented in this study would aid in determining resistance factors for probability‐based design of the tubular reinforced‐concrete members.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ang, A. H‐S., and Cornell, C. A. (1974). “Reliability basis of structural safety and design.” J. Struct. Div., ASCE, 100(9), 1755–1770.
2.
Ang, A. H‐S., and Tang, W. H. (1984). Probability concepts in engineering planning and design. John Wiley and Sons, Inc., New York, N.Y.
3.
Ellingwood, B., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American national standard A58.” Special Publication No. 577, National Bureau of Standards, Washington, D.C., Jun.
4.
Hognestad, E., Hanson, N. W., and McHenry, D. (1955). “Concrete stress distribution in utimate strength design.” J. Am. Concr. Inst., 52(6), 455–479.
5.
Kareem, A., and Hsieh, J. (1983). “Reliability of concrete chimneys under winds.” Report UHCE 83‐4, Dept. of Civil Engineering, Univ. of Houston, Houston, Tex., May.
6.
Kareem, A., and Hsieh, J. (1986). “Reliability analysis of concrete chimneys under wind loading.” J. Wind Engrg. and Industrial Aerodynamics, Elsevier Science Publishers B.V., Amsterdam, The Netherlands, 25, 93–112.
7.
MacGregor, J. G., Mirza, S. A., and Ellingwood, B. (1983). “Statistical analysis of resistance of reinforced and prestressed concrete members.” J. Am. Concr. Inst., 80(3), 167–176.
8.
MacGregor, J. G. (1983). “Load and resistance factors for concrete design.” J. Am. Concr. Inst., 80(4), 279–287.
9.
Madsen, H. O., Krenk, S., and Lind, L. C. (1986). Methods of structural safety. Prentice‐Hall Inc., Englewood Cliffs, N.J.
10.
Mirza, S. A., Hatzinikolas, M., and MacGregor, J. G. (1979). “Statistical descriptions of strength of concrete.” J. Struct. Div., ASCE, 105(6), 1021–1038.
11.
Mirza, S. A., and MacGregor, J. G. (1979). “Variability of mechanical properties of reinforcing bars.” J. Struct. Div., ASCE, 105(5), 921–938.
12.
Rubenstein, R. Y. (1981). Simulation and the Monte Carlo method. John Wiley and Sons, New York, N.Y.
13.
Rumman, W. S., and Ru‐Tsung, S. (1977). “Ultimate strength design of reinforced concrete chimneys.” J. Am. Concr. Inst., 74(4), 179–184.
14.
“Specification for design and construction of reinforced concrete chimneys.” (1979). ACI Standard 307‐79, American Concrete Institute, Detroit, Mich.
Information & Authors
Information
Published In
Copyright
Copyright © 1988 ASCE.
History
Published online: Apr 1, 1988
Published in print: Apr 1988
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.