Limit Design for Direct Control on Serviceability
Publication: Journal of Structural Engineering
Volume 114, Issue 2
Abstract
Any theory of design for reinforced concrete structures implies a minimum structural cost for which all failure modes, or limit states, are covered in the design for specified loading and geometric configuration of the structure. The critical limit states are safeguarded by adequate performance at ultimate and service design load levels through adopting a certain philosophy of design. The present paper proposes a limit‐state design method based on a design philosophy whereby direct design control is exercised on the service behavior of the structure by prespecifying the yield‐moment and rotation capacities of each of the critical sections of the structure. Both strength and deformability criteria are simultaneously satisfied in the design at the specified service and ultimate load levels. An optimal limit design formulation for the design problems is obtained. Suitable algorithms and related computer codes are used to solve the design problem having a nonlinear cost function and explicit nonlinear constraints. An example continuous beam is completely designed by the proposed method. A practical‐sized building frame example is also presented to demonstrate an application of the method to moderately complex framed structures.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
ACI. (1983). “Building code requirements for reinforced concrete.” ACI 318‐83, Detroit, Mich.
2.
Ali, M. M. (1977). “Optimal limit‐state design of reinforced concrete frameworks,” thesis presented to the University of Waterloo, at Waterloo, Ontario, Canada, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
3.
Ali, M. M., and Grierson, D. E. (1974). “Reinforced concrete design for strength and deformability.” J. Engrg. Mech. Div., ASCE, 103(10), 839–860.
4.
Ali, M. M., and Grierson, D. E. (1986). “Nonlinear design of reinforced concrete frameworks.” J. Struct. Engrg., ASCE, 112(10), 2216–2233.
5.
Baker, A. L. L. (1956). “Ultimate load theory applied to the design of reinforced and prestressed concrete frames.” Concrete Series, Concrete Publications Ltd., London, England.
6.
Best, M. J. (1972). “FCDPAK: A Fortran IV subroutine to solve differential mathematical programmes.” Technical Report, Department of Combinatorics and Optimization, University of Waterloo, Waterloo, Ontario, Canada.
7.
Best, M. J., and Bowler, A. T. (1975). “ACDPAC: A Fortran IV subroutine to solve differentiable mathematical programmes.” Research Report CORR 75‐26, Department of Combinatorics and Optimization, University of Waterloo, Waterloo, Ontario, Canada.
8.
Burnett, E. F. P., and Ali, M. M. (1976). “The significance of structural serviceability in reinforced concrete limit design.” presented at ACI Fall Convention, Mexico City, Mexico.
9.
Cohn, M. Z. (1965). “Optimum limit design for reinforced concrete continuous beams.” Proc. ICE, 30, Apr., London, England, 675–707.
10.
Cohn, M. Z. (1979). “Nonlinear design of concrete structures: problems and prospects.” International Symposium on Nonlinear Design of Concrete Structures, University of Waterloo, Waterloo, Ontario, Canada, 3–42.
11.
Cohn, M. Z., Burnett, E. F. P., and Grierson, D. E. (1969). “Safety, serviceability and efficiency of limit design for reinforced concrete beams and frames.” Publications IABSE, 29(1), 17–32.
12.
Corley, G. W. (1966). “Rotation capacity of reinforced concrete beams,” J. Struct. Div., ASCE, 92(ST5), 121–146.
13.
Furlong, R. W. (1970). “Design of concrete frames by assigned limit moments.” Journal ACI, 67(4), 341–353.
14.
Macchi, G. (1960). “A proposal of analysis based on the theory of imposed rotations.” Bulletin d'Information CEB, No. 21, Jan., Paris, France, Jan., 121–158 (in French).
15.
Mattock, A. H. (1965). “Rotation capacity of hinging regions in reinforced concrete beams.” Proceedings, International Symposium on Flexural Mechanics of Reinforced Concrete, Miami, Fla., ACI Special Publication SP‐12, 143–181.
16.
Munro, J., Krishnamurthy, C. S., and Yu, C. W. (1972). “Optimal design of reinforced concrete frames.” Struct. Engrg., 50(7), 259–264.
17.
Sawyer, H. A., Jr. (1964). “Design of concrete frames for two failure stages.” Proceedings, International Symposium on Flexural Mechanics of Reinforced Concrete, Miami, Fla., ACI Special Publication SP‐12, 405–437.
Information & Authors
Information
Published In
Copyright
Copyright © 1988 ASCE.
History
Published online: Feb 1, 1988
Published in print: Feb 1988
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.