Out‐of‐Plane Bending of Concrete Block Walls
Publication: Journal of Structural Engineering
Volume 114, Issue 1
Abstract
The test results for 21 full‐scale concrete block walls subjected to uniformly distributed loading normal to the surfaces of the walls are reported. The variables included in this experimental study include three wall lengths of 6.0 m (19 ft, 8 in.), 5.2 m (17 ft, 1 in.), and 3.6 m (11 ft, 10 in.) with a constant 2.8 m (9 ft, 2 in.) wall height. In addition, tests were performed with simple support conditions on all four boundaries, on the bottom and two sides, on only the two sides, and on only the top and bottom of the wall. Also, one series of tests was done with precompression loading in the vertical direction. Three repetitions for each combination of parameters were performed to provide a better statistical sample. The test results were compared with both elastic‐plate and yield‐line analyses. In these analyses, the bending strengths used were taken from tests of masonry assemblages constructed to allow testing of individual joints under bending normal to the bed joint and parallel to the bed joint. Both the load for first cracking and the failure load were investigated. A general evaluation of the comparable allowable wind loadings permitted by current building codes is also included.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Anderson, C. (1976). “Lateral loading tests on concrete block walls.” Struct. Eng., 54(7), 239–246.
2.
Baker, L. R. (1977). “The lateral strength of brickwork—an overview.” Report CEI, 1977 School of Engineering and Architecture, Deakin University, Geelong, Victoria, Australia.
3.
Baker, L. R. (1979). “A failure criterion for brickwork in bi‐axial bending.” Proceedings of 5th International Brick Masonry Conference, Washington, D.C., Oct., 41–43.
4.
Baker, L. R. (1980). Lateral loading of masonry panels. Structural Design of Masonry, Cement and Concrete Association of Australia, Sydney, Australia.
5.
Baker, L. R. (1981). “The flexural action of masonry structures under lateral load,” thesis presented to Deakin University, at Geelong, Victoria, Australia, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
6.
“Building code requirements for concrete masonry structures.” (1983). ACI 531‐83, American Concrete Institute, Detroit, Mich.
7.
Cajdert, A. (1980). “Laterally loaded masonry walls.” Publication 80:5, Chalmers University of Technology, Division of Concrete Structures, Goteborg, Sweden.
8.
Code of practice for structural use of masonry. Part 1—Unreinforced masonry. (1978). British Standards Institution, London, U.K.
9.
deVeckey, R. C., and West, H. W. H. (1980). “The flexural strength of concrete blockwork.” Mag. Concr. Res., 32, (113), 206–218.
10.
Drysdale, R. G., and Hamid, A. A. (1980). “Influence of block properties on the flexural strength of concrete masonry.” Seventh Australian Conference on the Mechanics of Structures and Materials, University of Western Australia, Perth, Australia, May, 179–184.
11.
Essawy, A., and Drysdale, R. G. (1983). “Capacity of block masonry under uniformly distributed loading normal to the surface of the wall.” Proceedings of the Third Canadian Masonry Symposium, Edmonton, Alberta, Canada, Paper No. 39, Jun., 39‐1–39‐16.
12.
Gairns, D. A. (1983). “Flexural behavious of concrete blockwork panels.” Thesis presented to the University of Melbourne, at Melbourne Australia, in partial fulfillment of the requirements for the degree of Master of Building Science.
13.
Haseltine, B. A. (1975). “Design of laterally loaded wall panels.” Proceedings of the British Ceramic Society, Loadbearing Brickwork, 5(24), Stoke‐on‐Trent, U.K., 115–126.
14.
Hendry, A. W., and Kheir, A. M. A. (1976). “The lateral strength of certain brickwork panels.” Proceedings of the Fourth International Brick Masonry Conference, Brugge, Belgium, 4.a.3.1–4.a.3.4.
15.
Hughes, D. M., and Zsembery, S. (1980). “A method of determining the flexural bond strength of brickwork at right angles to the bed joint.” Proceedings of the Second Canadian Masonry Symposium, Ottawa, Canada, 73–86.
16.
Lawrence, S. J. (1978). “The flexural behaviour of brickwork.” Proceedings of First North American Masonry Conference, Boulder, Colo. 20‐1–20‐18.
17.
Lawrence, S. J. (1980). “Design of masonry panels for lateral loading—some interim recommendations.” Technical Record 460, Experimental Building Station, Chatswood, N.S.W., Australia.
18.
“Masonry design and construction for buildings. (1984). CAN3‐S304‐M84, Canadian Standards Association, Rexdale, Ontario, Canada.
19.
“S.A.A. blockwork code, Part 1.—unreinforced blockwork. (1977). AS 1475, Standards Association of Australia, North Sydney, N.S.W., Australia.
20.
Timoshenko, S. (1959). Theory of plates and shells. 2nd Ed., McGraw‐Hill Book Co., New York, N.Y.
21.
West, H. W. H., Hodgkinson, H. R., and Webb, W. F. (1973a). “Lateral loading tests on walls with different boundary conditions.” Proceedings Third International Brick‐Masonry Conference, Essen, West Germany, 180–186.
22.
West, H. W. H., Hodgkinson, H. R., and Webb, W. F. (1973b). “The resistance of brick walls to lateral loading.” Proceedings of the British Ceramic Society, Loadbearing Brickwork, 4(21), Stoke‐on‐Trent, U.K., 141–164.
Information & Authors
Information
Published In
Copyright
Copyright © 1988 ASCE.
History
Published online: Jan 1, 1988
Published in print: Jan 1988
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.