Simplified Interaction Method for Sway Frames
Publication: Journal of Structural Engineering
Volume 110, Issue 5
Abstract
A number of simplifying assumptions are applied to a previously developed multi‐curve interaction method that determines the failure load of sway frames. These simplifications consider the establishment of the required parameters from a subassemblage analysis, the replacement of a rigorous second‐order analysis by a magnified first‐order solution and the determination of the “limiting slenderness ratio” from a single‐cycle approach. Furthermore, a graphical presentation of the major parameters is demonstrated. In all instances, the procedures are illustrated by examples. The results obtained by the simplified techniques indicate a good correlation with more rigorous approaches thus confirming that the presented procedures are suitable as a substitute for full‐scale elasto‐plastic computer solutions. They also produce results which are superior to the Merchant‐Rankine rule, which was proposed by the European Convention for Constructional Steelwork (ECCS) and is intended for inclusion in the new British Specification for the Structural use of Steelwork in Buildings.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Specification for the Design, Fabrication and Erection of Structural Steel for Buildings, American Institute of Steel Construction, (AISC), New York, N.Y., 1969.
2.
Specification for the Design, Fabrication and Erection of Structural Steel in Buildings, AISC, New York, N.Y., 1978.
3.
Anderson, D., “Simple Calculation of Elastic Critical Loads for Unbraced, Multi‐Story Steel Frames,” The Structural Engineer, Vol. 58A, No. 8, 1980, pp. 243–245.
4.
Draft Standard Specification for the Structural Use of Steelwork in Buildings, British Standards Institution (BSI), London, England, 1977.
5.
Cheong‐Siat‐Moy, F., “Results of Recent Frame Stability Studies with Reference to AS1250 Code Provisions,” Proceedings, 2nd Conference on Steel Development, Australian Institute of Steel Construction, Melbourne, Australia, 1977.
6.
Cheong‐Siat‐Moy, F., “Multi‐Story Frame Design Using Story Stiffness Concept,” Journal of the Structural Division, ASCE, Vol. 102, No. ST6, 1976, pp. 1197–1212.
7.
Cheong‐Siat‐Moy, F., “Automatic Plastic Analysis and Design of High Rise Steel Structures,” thesis presented to the University of Sydney, at Sydney, Australia, in 1974, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
8.
Cheong‐Siat‐Moy, F., “Strength of Steel Frames under Gravity Loads,” Journal of the Structural Division, ASCE, Vol. 103, No. ST6, 1977, pp. 1223–1235.
9.
Cheong‐Siat‐Moy, F., “Inelastic Sway Buckling of Multi‐Story Frames,” Journal of the Structural Division, ASCE, Vol. 102, No. ST1, 1976, pp. 65–75.
10.
Cheong‐Siat‐Moy, F., “Control of Deflections in Unbraced Steel Frames,” Proceedings, ICE, Part 2, Paper No. 7718, 1974, pp. 619–634.
11.
Fey, F., “Approximate Second‐Order Analysis of Reinforced Concrete Frames,” (in German), Bauingenieur, Berlin, Germany, June, 1966.
12.
Goldberg, J. E., “Approximate Methods for Stability and Frequency Analysis of Tall Buildings,” Proceedings, Conferencia Regional Sobre Edificios de Altura, Spain, Sept. 17–19, 1973, pp. 123–146.
13.
Jennings, A., and Majid, K., “An Elastic‐Plastic Analysis by Computer for Framed Structures Loaded up to Collapse,” The Structural Engineer, Vol. 43, No. 12, 1965, pp. 407–412.
14.
MacGregor, J. G., and Hage, S. E., “Stability Analysis and Design of Concrete Frames,” Journal of the Structural Division, ASCE, Vol. 103, No. ST10, 1977, pp. 1953–1970.
15.
MacGregor, J. G., “Theme II—Simple Design Procedures for Concrete Columns,” Introductory Report, 1974 Quebec Symposium on Design and Safety of Reinforced Concrete Compression Members, IABSE, Zurich.
16.
Merchant, W., “The Failure Load of Rigid Jointed Frameworks as Influenced by Stability,” The Structural Engineer, Vol. 32, 1954, pp. 185–190.
17.
Parme, A. L., “Capacity of Restrained Eccentrically Loaded Long Columns,” Special Publication SP13, Symposium on Reinforced Concrete Columns, ACI, Detroit, Mich., 1966, pp. 355–360.
18.
Rankine, W. J. M., Useful Rules and Tables, London, England, 1866.
19.
Rosenblueth, E., “Slenderness Effects in Buildings,” Journal of the Structural Division, ASCE, Vol. 91, No. ST1, 1967, pp. 229–252.
20.
Scholz, H., “A Multi‐Curve Interaction Method for the Plastic Analysis and Design of Unbraced and Partially‐Braced Frames,” thesis presented to the University of the Witwatersrand, Johannesburg, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
21.
Stevens, L. K., “Elastic Stability of Practical Multi‐Storey Frames,” Proceedings, ICE, Vol. 36, 1967, pp. 99–117.
22.
Wood, R. H., “Effective Lengths of Columns in Multi‐Story Buildings,” Building Research Establishment (BRE)‐Current Paper, CP 85/74, 1974.
Information & Authors
Information
Published In
Copyright
Copyright © 1984 ASCE.
History
Published online: May 1, 1984
Published in print: May 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.