Double‐Tapered Glulam Beams: Finite Element Analysis
Publication: Journal of Structural Engineering
Volume 110, Issue 5
Abstract
Stresses in double‐tapered, straight‐forward glulam beams are investigated by use of an orthotropic finite element method of analysis. Geometric and elastic materials parameters were varied to establish the sensitivity of the stress to these parameters. Beams studied were representative of beams that may occur in practice. Perpendicular‐to‐grain and flexural stresses from these results are compared to other methods of analysis and the current design provisions. Recommendations are made concerning the improvement of the present design procedures to reflect the findings reported in this paper. Graphs and equations of the perpendicular‐to‐grain tensile stress, as a function of the significant variables, are presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
“Design Procedure for Double‐Tapered Pitched and Curved Beams,” American Institute of Timber Construction, Technical Note No. 4, Englewood, Colo., June, 1977.
2.
Timber Construction Manual, American Institute of Timber Construction, Englewood, Colo., 1974.
3.
AITC 117‐79, “Determination of Design Values for Structural Glued Laminated Timber,” American Institute of Timber Construction, Englewood, Colo., 1979.
4.
AITC 117‐79, “Manufacturing Standard Specification for Structural Glued Laminated Timber of Softwood Species,” American Institute of Timber Construction, Englewood, Colo., 1979.
5.
Bathe, K. J., Wilson, E. L., and Peterson, F. E., “SAP IV—Structural Analysis Program for Static and Dynamic Response of Linear Systems,” Report No. ERC 73‐11, Univ. of California, Berkeley, 1973.
6.
Bodig, J., and Goodman, J. R., “Prediction of Elastic Parameters for Wood,” Wood Science, Vol. 5, No. 4, Apr., 1973.
7.
Dewey, G. R., “Analysis and Testing of Single‐ and Double‐Tapered Glulam Beams,” thesis presented to Colorado State University, Fort Collins, Colo., in 1979 in partial fulfillment of the requirements for the degree of Master of Science.
8.
Ellingwood, B., “Reliability of Wood Structural Elements,” Journal of the Structural Division, ASCE, Vol. 107, No. ST1, Jan., 1981.
9.
Foschi, R. O., “Stresses in Curved Glued‐Laminated Timber Beams: Experimental Study,” Forest Products Research Society, Madison, Wisc., July, 1971.
10.
Fox, S. P., “Experimental Verification of a Stress Analysis Method for Double‐Tapered Pitched Glued‐Laminated Beams,” Canadian Forestry Service, Publication No. 1277, 1970.
11.
Gopu, V. K. A., “Behavior of Double‐Tapered Curved Glulam Beams,” dissertation presented to the Colorado State University at Fort Collins, Colo., in 1975, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
12.
Gopu, V. K. A., and Goodman, J. R., “Full‐Scale Tests on Tapered and Curved Glulam Beams,” Journal of the Structural Division, ASCE, Vol. 101, No. ST12, Dec., 1975.
13.
Gopu, V. K. A., and Goodman, J. R., “Design of Double‐Tapered Pitched and Curved Glulam Beams,” Journal of the Structural Division, ASCE, Vol. 103, No. ST10, Oct., 1977.
14.
Gutkowski, R. M., “Shear Strength of Tapered Wood Beams,” Discussion, Journal of the Structural Division, ASCE, Vol. 108, No. ST3, Mar., 1982.
15.
Gutkowski, R. M., and Dewey, G. R., “Research on Double‐Tapered Glulam Beams,” Final Report, 11th World Congress of the International Association of Bridge and Structural Engineers, Vienna, 1980.
16.
Gutkowski, R. M., Dewey, G. R., and Goodman, J. R., “Full Scale Tests on Double‐Tapered Glulam Beams,” Journal of the Structural Division, ASCE, Vol. 108, No. ST10, 1982.
17.
Gutkowski, R. M., Dewey, G. R., and Goodman, J. R., “Full Scale Tests on Single‐Tapered Glulam Beams,” Journal of the Structural Division, ASCE, Vol. 108, No. ST10, Oct., 1982.
18.
Gutkowski, R. M., and Dewey, G. R., “Design Stress Capacities of Tapered Glulam Members,” Journal of Structural Engineering, ASCE, Vol. 110, No. 3, Mar., 1984.
19.
Maki, A. C., and Kuenzi, E. W., “Deflection and Stresses of Tapered Wood Beams,” U.S. Forest Service Research Paper, FPL 34, Sept., 1965.
20.
Norris, C. B., “Strength of Orthotropic Materials Subjected to Combined Stresses,” Forest Products Laboratory, FPL 1816, Mar., 1966.
21.
Thut, W. K., “Stresses in Pitch‐Cambered Glulam Beams,” thesis presented at the University of British Columbia, at British Columbia, Canada, in 1970, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 110 • Issue 5 • May 1984
Pages: 978 - 991
Copyright
Copyright © 1984 ASCE.
History
Published online: May 1, 1984
Published in print: May 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.