Simple Collapse Analysis of Plates in Compression
Publication: Journal of Structural Engineering
Volume 110, Issue 12
Abstract
A simplified elastic‐plastic analysis is presented for plates uniaxially compressed in their plane. The plates are not initially flat, and contain residual stresses due to welds at the longitudinal edges. Simple assumptions are made about the shortening‐deflection relationship, the modeling of welding residual stresses and the behavior of stress‐resultants after yielding. The assumptions are based on physical models, and are tested against data from previous numerical solutions. A full‐section yield criterion is used. The analysis is sufficiently simple to allow hand calculations. Load‐shortening curves are shown to be in good agreement with numerical solution methods and strengths are in agreement with test data. Simple criteria are given for the plate shortening at which the maximum loads are carried by welded and unwelded plates. These lead to single calculations of plate strength.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Association of State Highway and Transportation Officials, “Proposed Design Specification for Steel Box Girder Bridges,” Report FHWA‐TS‐80‐205, Federal Highway Administration, Washington, 1980.
2.
Bradfield, C. D., “Analysis of Measured Distortions in Steel Box‐Girder Bridges,” Report CUED/C‐Struct/TR.42, University of Cambridge, Dept. of Engrg., 1974.
3.
Bradfield, C. D., “Tests on Plates Loaded in In‐Plane Compression,” Journal of Construction Steel Research, London, Vol. 1, 1980, pp. 27–37.
4.
Bradfield, C. D., “An Evaluation of the Elastic‐Plastic Analysis of Steel Plates Loaded by Uniaxial In‐Plane Compression,” International Journal of Mechanical Sciences, Oxford, Vol. 24, No. 3, 1982, pp. 127–146.
5.
BS.5400: “Steel, Concrete and Composite Bridges, Part 3: Code of Practice for Design of Steel Bridges,” BS5400: Part 3, British Standards Institution, London, 1982.
6.
BS.5400: “Steel, Concrete and Composite Bridges: Part 6: Specification for Materials and Workmanship, Steel,” BS5400: Part 6, British Standards Institution, London, 1980.
7.
Chatterjee, S., and Dowling, P. J., “The Design of Box‐Girder Compression Flanges,” presented at the July 1976 International Symposium on Steel Plated Structures, held at Imperial College, London, Paper 8.
8.
Crisfield, M. A., “Large‐deflection Elasto‐Plastic Buckling Analysis of Plates using Finite Elements,” TRRL Report LR 593, Transport and Road Research Lab., Crowthorne, England, 1973.
9.
Crisfield, M. A., “On an Approximate Yield Criterion for Thin Steel Shells,” TRRL Report LR 658, Transport and Road Research Lab., Crowthorne, England, 1974.
10.
Crisfield, M. A., “Full Range Analysis of Steel Plates and Stiffened Plating Under Uniaxial Compression,” Proceedings of the Institution of Civil Engineers, London, Part 2, Vol. 59, Dec., 1975, pp. 595–624.
11.
Crisfield, M. A., “The Automatic Non‐Linear Analysis of Stiffened Plates and Shallow Shells Using Finite Elements,” Proceedings of the Institution of Civil Engineers, London, Part 2, Vol. 69, Dec., 1980, pp. 891–909.
12.
Dawson, R. G., and Walker, A. C., “Post‐Buckling of Geometrically Imperfect Plates,” Journal of the Structural Division, ASCE, Vol. 93, No. ST1, 1972, pp. 75–94.
13.
Dwight, J. B., and Moxham, K. E., “Welded Steel Plates in Compression,” Structural Engineer, London, Vol. 47, Feb., 1969, pp. 49–66.
14.
Frieze, P. A., “Ultimate Load Behavior of Steel Box‐Girders and Their Components,” thesis presented to Imperial College, University of London, in 1975, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
15.
Frieze, P. A., Dowling, P. J., and Hobbs, R. E., “Parametric Study on Plates in Compression,” Report BG 39, Civil Engineering Dept., Imperial College, London, 1975.
16.
Frieze, P. A., Dowling, P. J., and Hobbs, R. E., “Ultimate Load Behaviour of Plates in Compression,” presented at the July 1976 International Symposium on Steel Plated Structures, held at Imperial College, London, Paper 2.
17.
Gerard, G., and Becker, H., “Handbook of Structural Stability. I: Buckling of Flat Plates,” Technical Note 3781, National Advisory Committee on Aeronautics, Washington, 1957.
18.
Harding, J. E., “Bolted Spliced Panels and Stress Redistribution in Box‐Girder Components up to Collapse,” thesis presented to Imperial College, University of London, in 1975, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
19.
Harding, J. E., Hobbs, R. E., and Neal, B. G., “Ultimate Load Behaviour of Plates Under Combined Direct and Shear In‐Plane Loading,” presented at the July 1976 International Symposium on Steel Plated Structures, held at Imperial College, London, Paper 15.
20.
Harding, J. E., Hobbs, R. E., Neal, B. G., and Slatford, J., “Parametric Study on Plates Under Combined Direct and Shear In‐Plane Loading,” Report BG 44, Civil Engineering Dept, Imperial College, London, 1976.
21.
Horne, M. R., and Narayanan, R., “An Approximate Method for the Design of Stiffened Steel Compression Panels,” Proceedings of the Institution of Civil Engineers, London, Part 2, Vol. 59, Sept., 1975, pp. 501–514.
22.
Ilyushin, A. A., “Elasticity,” translated from the Russian into French, by A. Popoff and P. Thomé, Editions Eyrolles, Paris, 1956. N. B. French spelling is ‘Iliochiene’.
23.
Little, G. H., “Rapid Analysis of Plate Collapse by Live‐Energy Minimisation,” International Journal of Medianical Sciences, Oxford, Vol. 19, No. 12, 1977, pp. 725–744.
24.
Little, G. H., “The Collapse of Rectangular Steel Plates Under Uniaxial Compression,” Structural Engineer, London, Vol. 58B, Sept., 1980, pp. 45–61.
25.
Mayers, J., and Budiansky, B., “Analysis and Behaviour of Simply Supported Flat Plates Compressed Beyond the Buckling Load into the Plastic Range,” Technical Note 3368, National Advisory Committee on eronautics, Washington, 1955.
26.
Moxham, K. E., “Compression in Welded Web Plates,” thesis presented to the University of Cambridge, in 1970, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
27.
Moxham, K. E., and Bradfield, C. D., “The Strength of Welded Steel Plates Under In‐Plane Compression,” Report CUED/C‐Struct/TR.65, Department of Engineering, University of Cambridge, 1977.
28.
Rhodes, J., “On the Approximate Prediction of Elasto‐Plastic Plate Behaviour,” Proceedings of the Institution of Civil Engineers, London, Part 2, Vol. 71, Mar., 1981, pp. 165–183.
29.
Rhodes, J., and Harvey, J. M., “Plates in Uniaxial Compression with Various Support Conditions at the Unloaded Boundaries,” International Journal of Mechanical Sciences, Oxford, Vol. 13, 1971, pp. 787–802.
30.
Robinson, M., “A Comparison of Yield Surfaces for Thin Shells,” International Journal of Mechanical Sciences, Oxford, Vol. 13, No. 4, 1971, pp. 345–354.
31.
Stein, M., “Loads and Deformations of Buckled Rectangular Plates,” Technical Report R‐40, National Aeronautics and Space Administration, Washington, 1959.
32.
Stonor, R. W. P., “Unstiffened Steel Compression Panels with and without Coincident Shear,” thesis submitted to the University of Cambridge, in Oct. 1980, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
33.
Walker, A. C., “The Post‐Buckling Behaviour of Simply‐Supported Square Plates,” Aeronautical Quarterly, London, Vol. 20, Aug., 1969, pp. 203–222.
34.
Williams, D. G., “Some Examples of the Elastic Behaviour of Initially Deformed Bridge Panels,” Civil Engineering and Public Works Review, Vol. 66, No. 783, Oct., 1971, pp. 1107–1112.
35.
Williams, D. G., and Walker, A. C., “Explicit Solutions for the Design of Initially Deformed Plates Subject to Compression,” Proceedings of the Institution of Civil Engineers, London, Part 2, Vol. 59, Dec., 1975, pp. 763–787.
36.
Williams, D. G., and Walker, A. C., “Explicit Solutions for Plate Buckling Analysis,” Journal of the Engineering Mechanics Division, ASCE, Vol. 103, No. EM4, 1977, pp. 549–568.
Information & Authors
Information
Published In
Copyright
Copyright © 1984 ASCE.
History
Published online: Dec 1, 1984
Published in print: Dec 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.