Locally Buckled Thin‐Walled Columns
Publication: Journal of Structural Engineering
Volume 110, Issue 11
Abstract
An effective section method is presented for analyzing the effects of local buckling on the overall modes of behavior of singly symmetric, thinwalled columns and beam‐columns. The post‐local buckling strength of the component plate elements is recognized through effective width concepts. A single effective width equation is developed to represent the subultimate behavior under service loads and the ultimate strength of uniformly compressed stiffened elements. Also, an effective width approach is.proposed for predicting the response of eccentrically compressed stiffened elements. An experimental investigation is reported on cold‐formed, lipped channel, steel columns with concentric or eccentric loading. Predictions obtained with the presented analysis method are in good correspondence with experimental subultimate deflections and ultimate strength. In contrast to this, current design methods are shown to be inadequate for predicting the experimental results. In certain cases, laterally unbraced (edge) stiffened elements are prone to an elastic local torsional failure mode. A limiting stress approach is proposed for this situation, which provides fair agreement with limited experimental data.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Dawson, R. G., and Walker, A. C., “Post‐Buckling of Geometrically Imperfect Plates,” Journal of the Structural Division, ASCE, Vol. 98, No. ST1, Jan., 1972, pp. 75–94.
2.
Desmond, T. P., “The Behavior and Strength of Thin‐Walled Compression Elements with Longitudinal Stiffeners,” Report 369, Department of Structural Engineering, Cornell University, Ithaca, N.Y., Sept., 1978.
3.
DeWolf, J. T., Pekoz, T., and Winter, G., “Local and Overall Buckling of Cold‐Formed Members,” Journal of the Structural Division, ASCE, Vol. 100, No. ST10, Oct., 1974, pp. 2017–2036.
4.
Douty, R. T., “A Design Approach to the Strength of Laterally Unbraced Compression Flanges,” Bulletin 37, Engineering Experiment Station, Cornell University, Ithaca, N.Y., 1962.
5.
Graves Smith, T. R., “The Ultimate Strength of Locally Buckled Columns of Arbitrary Length,” Thin Walled Steel Structures, K. C. Rockey and H. V. Hill, eds., Crosby Lockwood, London, England, 1969, pp. 35–60.
6.
Hornbeck, R. W., Numerical Methods, Quantum Publishers, Inc., New York, N.Y., 1975.
7.
Johnston, B. G., ed., Guide to Stability Design Criteria for Metal Structures, 3rd Ed., John Wiley and Sons, Inc., New York, N.Y., 1976.
8.
Kalyanaraman, V., Pekoz, T., and Winter, G., “Unstiffened Compression Elements,” Journal of the Structural Division, ASCE, Vol. 103, No. ST9, Proc. Paper 13197, Sept., 1977, pp. 1833–1848.
9.
Kalyanaraman, V., “Performance of Unstiffened Compression Elements,” Report 362, Department of Structural Engineering, Cornell University, Ithaca, N.Y., Feb., 1978.
10.
Konig, J., and Thomasson, P.‐O., “Thin‐Walled C‐Shaped Panels Subject to Axial Compression or to Pure Bending,” Thin‐Walled Structures—Recent Technical Advances and Trends in Design, Research and Construction, J. Rhodes and A. C. Walker, eds., Granada, London, England, 1980.
11.
LaBoube, R. A., “Webs for Cold‐Formed Steel Flexural Members—Structural Behavior of Beam Webs Subjected to Bending Stress,” Civil Engineering Study 78‐1, Structural Series, University of Missouri‐Rolla, Rolla, Mo., June, 1978.
12.
Loughlan, J., “Mode Interaction in Lipped Channel Columns Under Concentric or Eccentric Loading,” thesis presented to the University of Strathcylde, at Glasgow, Scotland, in 1979, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
13.
Mulligan, G. P., “The Influence of Local Buckling on the Structural Behavior of Singly‐Symmetric Cold‐Formed Steel Columns,” thesis prepared to Cornell University, at Ithaca, N.Y., in 1983, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
14.
Pekoz, T., “Torsional Flexural Buckling of Thin‐Walled Sections Under Eccentric Load,” Research Bulletin 69‐1, Department of Structural Engineering, Cornell University, Ithaca, N.Y., Sept., 1969.
15.
Rhodes, J., and Loughlan, J., “Simple Design Analysis of Lipped Channel Columns,” presented at the 1980, Fifth International Specialty Conference of Cold‐Formed Steel Structures held at St. Louis, Mo.
16.
Specification for the Design of Cold‐Formed Steel Structural Members, American Iron and Steel Institute, Washington, D.C., 1980.
17.
Supplementary Information on the 1968 Edition of the Specification for the Design of Cold‐Formed Steel Structural Members, American Iron and Steel Institute, Washington, D.C., 1971.
18.
Thomasson, P.‐O., “Thin‐Walled C‐Shaped Panels in Axial Compression,” Document D1: 1978, Swedish Council for Building Research, Stockholm, Sweden, 1978.
19.
Timoshenko, S., Strength of Materials—Part I Elementary Theory and Problems, 3rd Ed., D. Van Nostrand Co., Princeton, N.J., 1955.
20.
Usami, T., “Post‐Buckling of Plates in Compression and Bending,” Journal of the Structural Division, ASCE, Vol. 108, No. ST3, Proc. Paper 16943, Mar., 1982, pp. 591–609.
21.
Winter, G., Commentary on the 1968 Edition of the Specification for the Design of Cold‐Formed Steel Structural Members, American Iron and Steel Institute, Washington, D.C., 1970.
22.
Yamaki, N., “Postbuckling Behavior of Rectangular Plates with Small Initial Curvature Loaded in Edge Compression,” Journal of Applied Mechanics, Vol. 26, Sept., 1959.
Information & Authors
Information
Published In
Copyright
Copyright © 1984 ASCE.
History
Published online: Nov 1, 1984
Published in print: Nov 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.