Spectral-Based Peak-Shear-Strength Criterion for Rock Joints
Publication: Journal of Geotechnical Engineering
Volume 121, Issue 11
Abstract
In general, roughness profiles of rock joints consist of nonstationary and stationary components. At the simplest level, only one parameter is necessary to quantify nonstationary joint roughness. To capture the nonstationary roughness, it is suggested that the average inclination angle I, along with the direction considered for the joint surface, be used. Most natural rock-joint surface profiles do not belong to the self-similar fractal category. However, they may be modeled by self-affine fractals. It is shown that even though the fractal dimension D is a useful parameter, it alone is insufficient to quantify the stationary roughness of non-self-similar profiles. A new strength criterion, which includes three roughness parameters ( D, I, and a spectral coefficient, K s ), is suggested for modeling the anisotropic peak shear strength of rock joints at low normal effective stresses. Joint roughness data should be used to estimate the roughness parameters in different directions on the joint surface. Parameter D reflects the rate of change in length of the profile in response to a change in the scale of measurement r . Parameter K s may be used to model the scale effect. A validation study shows that the new equation has good capability to predict the anisotropic peak shear strength of joints. In practice, to allow for modeling uncertainties, the new equation should be used with a factor of safety of about 1.5. Comparisons are also shown between the predicted shear strengths based on Barton's equation and the measured peak shear strengths.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Barton, N.(1973). “Review of a new shear strength criterion for rock joints.”Engrg. Geol., 7(4), 287–332.
2.
Berry, M. V., and Lewis, Z. V. (1980). “On the Weierstrass-Mandelbrot fractal function.”Proc., Royal Society of London, England, Ser. A., Vol. 370, 459–484.
3.
Brown, S. R., and Scholz, C. H. (1985). “Broad band width study of the topography of natural rock surfaces.”J. Geophys. Res., 90 (B14), 12575–12582.
4.
Hsiung, S. M., Ghosh, A., Ahola, M. P., and Chowdhury, A. H.(1993). “Assessment of conventional methodologies for joint roughness coefficient determination.”Int. J. Rock Mech. Min. Sci., 30(7), 825–829.
5.
Huang, T. H., and Doong, Y. S. (1990). “Anisotropic shear strength of rock joints.”Proc., Int. Symp. on Rock Joints, A. A. Balkema, Rotterdam, The Netherlands, 211–218.
6.
Huang, S. L., Oelfke, S. M., and Speck, R. C.(1992). “Applicability of fractal characterization and modelling to rock joint profiles.”Int. J. Rock Mech. Min. Sci., 29(2), 89–98.
7.
Jing, L., Nordlund, E., and Stephansson, O.(1992). “An experimental study on the anisotropy and stress dependency of the strength and deformability of rock joints.”Int. J. Rock Mech. Min. Sci., 29(6), 535–542.
8.
Kodikara, J. K., and Johnston, I. W.(1994). “Shear behaviour of irregular triangular rock-concrete joints.”Int. J. Rock Mech. Min. Sci., 31(4), 313–322.
9.
Kulatilake, P. H. S. W., Shou, G., Huang, T.-H., and Morgan, R. M. (1994). “A new peak shear strength criterion for rock joints.”Proc., 1st North American Rock Mech. Symp., A. A. Balkema, Rotterdam, The Netherlands, 565–572.
10.
Ladanyi, B., and Archambault, G. (1969). “Simulation of the shear behavior of a jointed rock mass.”Proc., 11th Symp. on Rock Mech., Vol. 7, 105–125.
11.
Maerz, N. H., Franklin, J. A., and Bennett, C. P.(1990). “Joint roughness measurement using shadow profilometry.”Int. J. Rock Mech. Min. Sci., 27(5), 329–343.
12.
Mandelbrot, B. B. (1983). The fractal geometry of nature . W. M. Freeman, and Co., San Francisco, Calif.
13.
Mandelbrot, B. B.(1985). “Self-affine fractals and fractal dimension.”Physica-Scripta, Stockholm, Sweden, 32(4), 257–260.
14.
Miller, S. M., McWilliams, P. C., and Kerkering, J. C. (1990). “Ambiguities in estimating fractal dimensions of rock fracture surfaces.”Proc., 31st U.S. Symp. on Rock Mech., A. A. Balkema, Rotterdam, The Netherlands, 471–478.
15.
Odling, N. E.(1994). “Natural fracture profiles, fractal dimension and joint roughness coefficients.”Rock Mech. Rock Engrg., 27(3), 135–153.
16.
Patton, F. D. (1966). “Multiple modes of shear failure in rock.”Proc., 1st Congr. of Int. Soc. of Rock Mech., Vol. 1, 509–513.
17.
Power, W. L., and Tullis, T. E. (1991). “Euclidean and fractal models for the description of rock surface roughness.”J. Geophys. Res., 96(B1), 415–424.
18.
Shou, G. (1994). “Joint roughness characterization and effect of roughness on peak shear strength of joints,” PhD dissertation, Univ. of Arizona, Tucson, Ariz.
Information & Authors
Information
Published In
Copyright
Copyright © 1995 American Society of Civil Engineers.
History
Published online: Nov 1, 1995
Published in print: Nov 1995
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.