Upsetting Tests of Fresh Cementitious Composites for Extrusion
Publication: Journal of Engineering Mechanics
Volume 132, Issue 2
Abstract
Upsetting tests were conducted on cylindrical specimens made of a typical fresh short fiber-reinforced cementitious composite (SFRCC) paste for extrusion at various boundary conditions to derive the paste’s constitutive behavior. Due to friction present at the specimen and the equipment platens interfaces, stress was not uniformly distributed in the specimen and had to be corrected. In this study, two analytical methods were utilized to derive the true flow stress of the fresh SFRCC paste through correcting the nominal yield stress obtained from the upsetting test. One of them was the stress extrapolation method, which required a large number of experimental data and predetermined boundary friction. It was found that the results corrected by this method from experiments at the lubricated boundary were more reliable than those at the dry boundary and this method could also give an approximate estimation of the boundary friction coefficient. As comparison, the flow stress correction method required only a small amount of experimental data and no predetermined boundary friction. It was found that this method provided better results at the dry boundary than at the lubricated boundary. The fresh SFRCC paste exhibited both strain and strain rate hardening characteristics whereas strain rate hardening effect was more significant and dominated.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support from Hong Kong Research Grant Council under Grant No. UNSPECIFIEDHKUST 6226/01E is gratefully acknowledged. The writers would also thank KURARAY Co. Ltd. for providing the short PVA fibers.
References
Adams, M. J., Biswas, S. K., Briscoe, B. J., and Kamyab, M. (1991). “The effects of interface constraints on the deformation of pastes.” Powder Technol., 65(1–3), 381–392.
Bridgman, P. W. (1952). Studies in large plastic flow and fracture with special emphasis on the effects of hydrostatic pressure, McGraw-Hill, New York.
Chen, F.-K., and Chen, C.-J. (2000). “On the nonuniform deformation of the cylinder compression test.” J. Eng. Mater. Technol., 122(2), 192–197.
Ettouney, O., and Hardt, D. E. (1983). “A method for in-process failure prediction in cold upset forging.” J. Eng. Ind., 105(3), 161–167.
Ettouney, O. M., and Stelson, K. A. (1990). “An approximation method to calculate folder and strains during cold upsetting of cylinders. Part II: Use of the foldover model to estimate friction.” J. Eng. Ind., 112(3), 267–271.
Ford, H. (1963). Advanced mechanics of materials, Longmans, London.
Kulkarni, K. M., and Kalpakjian, S. (1969). “A study of barreling example of free deformation.” J. Eng. Ind., 91(3), 743–754.
Malayappan, S., and Narayanasamy, R. (2003). “Observations of barrelling in aluminium solid cylinders during cold upsetting using different lubricants.” Mater. Sci. Technol., 19(12), 1705–1708.
Zhou, X., and Li, Z. (2005). “Characterizing rheology of fresh short fiber reinforced cementitious composite through capillary extrusion.” J. Mater. Civ. Eng., 17(1), 28–35.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Aug 17, 2004
Accepted: Mar 21, 2005
Published online: Feb 1, 2006
Published in print: Feb 2006
Notes
Note. Associate Editor: Eric N. Landis
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.