Stability of Stiffened Plates with Initial Imperfections
Publication: Journal of Engineering Mechanics
Volume 129, Issue 7
Abstract
An experimental study of the effect of plate slenderness ratio and column slenderness ratio on the collapse load of simply supported stiffened plates with initial imperfections, loaded in compression, is presented. A generalized computer program for the semiempirical solutions based on the strut approach and the orthotropic plate approach is developed. A finite element analysis program based on the orthotropic plate approach is developed and a new collapse criterion is introduced. The analytical calculations are compared with the experimental results and uncertainty parameters are calculated. The effect of initial geometric imperfections, plate slenderness ratios, and column slenderness ratios on the collapse load of stiffened plates is studied. A set of conclusions is drawn based on the experimental and analytical studies carried out.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alagusundaramoorthy, P. (1993). “Ultimate strength of stiffened panels.” PhD thesis, Ocean Engineering Centre, IIT, Madras, India.
Allen, D.(1975). “Analysis and design of stiffened plates for collapse load, correspondence 1.” Struct. Eng., 53(9), 381–382.
American Society for Metals (ASM). (1985). “Metals handbook 9 Edition.” Mechanical testing, American Society for Metals, Metals Park, Ohio, 8, 28–33.
Bogner, F. K., Fox, R. L., and Schmit, L. A. (1965). “The generation of inter-element compatible stiffness and mass matrices by the use of interpolation formulas.” Proc., Int. Conf. on Matrix Methods in Structural Mechanics, J. S. Przemieniecki et al., eds., Air Force Flight Dynamics Laboratory, Wright–Patterson Air Force Base, Dayton, Ohio, 397–443.
British Standards Institution (BSI) 5400. (1980). “Steel, concrete and composite bridges.” Part 6, Fabrication tolerances, British Standards Institution, London.
Chatterjee, S., and Dowling, P. J. (1976). “The design of box girder compression flanges.” Proc., Int. Symp. on Steel Plated Structures, P. J. Dowling et al., eds., The Institution of Structural Engineers, London, 196–228.
Crisfield, M. A. (1975). “Full-range analysis of steel plates and stiffened plating under uniaxial compression.” Proc., Inst. of Civil Engineers (ICE), London, 59(2), 595–624.
Dowling, P. J., Chatterjee, S., Frieze, P. A., and Moolani, F. M. (1973). “Experimental and predicted collapse behaviour of rectangular steel box girders.” Proc., Int. Conf. on Steel Box Girder Bridges, P. Cartledge, ed., Institution of Civil Engineers, London, 77–94.
Dwight, H. B., and Little, G. H.(1976). “Stiffened steel compression flanges—A simpler approach.” Struct. Eng., 54(12), 501–509.
Eurocode 3. (1997). “Supplementary rules for planar plated structures without transverse loading.” ENV 1993-1-5.
Faulkner, D.(1975). “A review of effective plating for use in the analysis of stiffened plating in bending and compression.” J. Ship Res., 19(1), 1–17.
Faulkner, D. (1976). “Compression tests on welded eccentrically stiffened plate panels.” Proc., Int. Symp. on Steel Plated Structures, P. J. Dowling et al., eds., The Institution of Structural Engineers, London, 581–617.
Greville, T. N. E. (1967). “Spline functions, interpolation and numerical quadrature.” Mathematical methods for digital computers, A. Ralston and H. S. Wilf, eds., Wiley, New York, 2, 156–168.
Horne, M. R., and Narayanan, R.(1977). “Design of axially loaded stiffened plates.” J. Struct. Div., ASCE, 103(11), 2243–2257.
Hu, P. C., Lundquist, E. E., and Batdorf, S. B. (1946). “Effect of small deviations from flatness of effective width and buckling of plates and compression.” NACA TN Rep. No. 1124, National Advisory Committee for Aeronautics, Washington, D.C.
Mallet, R. H., and Marcal, P. V.(1968). “Finite-element analysis of nonlinear structures.” J. Struct. Div., ASCE, 94(9), 2081–2105.
Maquoi, R., and Massonet, C. (1971). “Non-linear theory of post buckling resistance of large stiffened box girders.” Int. Assoc. for Bridge and Structural Engineers, Zurich, Switzerland, 31(2), 91–140 (in French).
Murray, N. W.(1975). “Analysis and design of stiffened plates for collapse load.” Struct. Eng., 53(3), 153–158.
Pfluger, A.(1947). “About the buckling problem of the anisotropic rectangular plate.” Ing. Arch., 16, 111–120 (in German).
Rajasekaran, S., and Murray, D. W.(1973). “Incremental finite element matrices.” J. Struct. Div., ASCE, 99(12), 2423–2438.
Robertson, A. (1925). The strength of struts, Selected engineering papers, Inst. of Civil Engineers, London, 28, 1–55.
Shanmugam, N. E., Paramasivam, P., and Lee, S.-L.(1986). “Stiffened flanges containing openings.” J. Struct. Div., ASCE, 112(10), 2234–2246.
Smith, C. S.(1975). “Compressive strength of welded steel ship grillages.” Trans. RINA, London, 117, 325–359.
Wolchuk, R. (1981). “Design rules for steel box-girder bridges.” Proc., Int. Assoc. for Bridge and Structural Engineers, Lisbon, 41–81.
Wolchuk, R., and Mayrbaurl, R. M. (1980). “Proposed design specifications for steel box-girder bridges.” Rep. No. FHWA-TS-80-205, Federal Highway Administration, Washington, D.C.
Information & Authors
Information
Published In
Copyright
Copyright © 2003 American Society of Civil Engineers.
History
Received: Feb 25, 2000
Accepted: Dec 20, 2002
Published online: Jun 13, 2003
Published in print: Jul 2003
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.