Analysis of Penetration Resistance of Concrete
Publication: Journal of Engineering Mechanics
Volume 124, Issue 3
Abstract
A combined numerical and analytical study of penetration of concrete by high-velocity (∼1.8 km/s) projectiles has been conducted in order to study the effects of concrete's constitutive modeling on penetration calculations. The results of the analysis are compared with the available experimental data. All constitutive models studied accounted for the compressibility of concrete. The plastic yield condition was modeled with the von Mises yielding criterion using (1) the constant yield-strength mode; and (2) the pressure-dependent yield-strength model. Regardless of the value of the yield strength, application of a constant yield strength model is shown to result in nearly identical hole profiles that, in all cases, were significantly larger than those obtained through experimentation. Crater profiles calculated with the pressure-dependent yield model showed good agreement with the available experimental data, attributed to the increased target resistance to penetration. In addition, a detailed analysis of the flow field along the central streamline shows that the increase in the target's resistance to penetration is also responsible for the growth in the time rate of the projectile erosion.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Alekseevskii, V. P. (1966). “Penetration of a rod into a target at high velocity.”Combustion, explosion and shock waves, Vol. 2. Faraday Press, New York, N.Y., 63–66.
2.
Anderson, C. E., and Walker, J. D.(1991a). “An examination of long-rod penetration.”Int. J. Impact Engrg., 11, 481–501.
3.
Anderson, C. E., and Walker, J. D. (1991b). “Long-rod penetration and calculation of target resistance.”Shock compression of condensed matter, S. C. Schmidt, R. D. Dick, J. W. Forbes, and D. G. Tasker, eds., Elsevier Science Publishers BV, Amsterdam, The Netherlands, 967–970.
4.
Birkhoff, G., MacDougall, D. P., Pugh, E. M., and Sir Taylor, G.(1948). “Explosives with lined cavities.”J. Appl. Phys., 19, 563–582.
5.
Bishop, R. F., Hill, R., and Mott, N. F.(1945). “The theory of indentation and hardness tests.”Proc., Phys. Soc., 57(3), 147–159.
6.
Christman, D. R., and Gehring, J. W.(1966). “Analysis of high-velocity penetration mechanics.”J. Appl. Phys., 37, 1579–1587.
7.
Eichelberger, R. J.(1956). “Experimental test of the theory of penetration by metallic jets.”J. Appl. Phys., 27, 63–68.
8.
Forrestal, M. J., Norwood, F. R., and Longcope, D. P.(1981). “Penetration into targets described by locked hydrostats and shear strength.”Int. J. Solids and Struct., 17, 915–924.
9.
Forrestal, M. J., Luk, V. K., and Watts, H. A.(1988). “Penetration of reinforced concrete with ogive-nose penetrators.”Int. J. Solids and Struct., 24, 77–87.
10.
Gehring, J. W. Jr. (1970). “Theory of impact on thin targets and shields and correlation with experiment.”High velocity impact phenomena, R. Kinslow, ed., Academic Press, New York, N.Y., 105–156.
11.
Gold, V. M., Vradis, G. C., and Pearson, J. C.(1996a). “Penetration of concrete by eroding projectiles: Experiments and analysis.”J. Engrg. Mech., ASCE, 122(2), 145–152.
12.
Gold, V. M., Vradis, G. C., and Pearson, J. C.(1996b). “Study of constitutive models for concrete penetration analysis.”J. Engrg. Mech., ASCE, 122(3), 230–238.
13.
Pei-Rong Lin, and Batra(1989). “Histories of the stress, strain-rate, temperature and spin in steady state penetration problems.”Int. J. Engrg. Sci., 27, 1155–1165.
14.
Pidsley, P. H.(1984). “A numerical study of long rod impact onto a large target.”Int. J. Mech. Sci., 32, 315–333.
15.
Read, H. E., and Maiden, C. J. (1971). “The dynamic behavior of concrete.”S-CUBED Rep. 3SR-707, Systems, Science and Software Corp., La Jolla, Calif.
16.
Steinberg, D. J., Cochran, S. G., and Guinan, M. W.(1980). “A constitutive model for metals applicable at high-strain rate.”J. Appl. Phys., 51(3), 1498–1504.
17.
Tate, A.(1967). “A theory for deceleration of long rods after impact.”J. Mech. Phys. Solids, 15, 387–399.
18.
Tate, A.(1969). “Further results in the theory of long rod penetration.”J. Mech. Phys. Solids, 17, 141–150.
19.
Tipton, R. E. (1991a). CALE users manual, version 910201. Lawrence Livermore Nat. Lab., Livermore, Calif.
20.
Tipton, R. E. (1991b). “EOS coefficients for the CALE code for some materials.” Lawrence Livermore Nat. Lab., Livermore, Calif.
21.
Tipton, R. E. (1991c). “Porous EOS in CALE used to model concrete.” Lawrence Livermore Nat. Lab., Livermore, Calif.
22.
Walker, J. D., and Anderson, C. E. Jr. (1992). “The influence of the initial nose shape on the shock phase of the impact.”Shock compression of condensed matter—1991, S. C. Schmidt, R. D. Dick, J. W. Forbes, and D. G. Tasker, eds. Elsevier Science Publishers BV, Amsterdam, The Netherlands, 943–946.
23.
Walker, J. D., and Anderson, C. E. Jr.(1994). “The influence of the initial nose shape in eroding penetration.”Int. J. Impact Engrg., 15, 139–148.
24.
Walker, J. D., and Anderson, C. E. Jr.(1995). “A time-dependent model for long-rod penetration.”Int. J. Impact Engrg., 16, 19–48.
25.
Wilkins, M. L. (1964). “Calculations of elastic-plastic flow.”Methods of computational physics, Vol. 3, B. Adler, S. Fernbach, and M. Rotenberg, eds., Academic Press, New York, N.Y., 211–263.
26.
Wilkins, M. L. (1969). “Calculations of elastic-plastic flow. UCRL-7322, Rev. 1, Lawrence Livermore Nat. Lab., Livermore, Calif.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Mar 1, 1998
Published in print: Mar 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.