Energy-Based Automatic Mixed-Mode Crack-Propagation Modeling
Publication: Journal of Engineering Mechanics
Volume 121, Issue 8
Abstract
Based on an energy principle and a virtual crack extension technique, a practical finite-element modeling approach for the automatic mixed-mode two-dimensional (2D) linear elastic fracture mechanics (LEFM) crack-propagation analysis has been developed. By decomposing the displacement field obtained from a conventional finite-element analysis into symmetric and antisymmetric displacement fields with respect to the crack, Mode-I and Mode-II energy release rates can be determined using a generalization of the stiffness derivative method, and the corresponding stress intensity factors can then be calculated. The load at which a crack propagates and the propagation direction can be determined using one of the well-established mixed-mode crack-propagation criteria. Unlike the previously developed approaches to crack propagation, this approach does not require the use of symmetric crack-tip mesh, nor crack-tip singular elements, which greatly simplifies the subsequent remeshing process to allow for crack propagation. The automatic crack-propagation process is achieved by using a simple and efficient local 2D remeshing algorithm that can be easily programmed. Convergence studies, mesh sensitivity studies, and the practical use of the new approach are presented through various example problems.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Arrea, A., and Ingraffea, A. R. (1982). “Mixed-mode crack propagation in mortar and concrete.”Rep. No. 81-13, Cornell Univ., Ithaca, N.Y.
2.
Banks-Sills, L., and Sherman, D.(1986). “Comparison of methods for calculating stress intensity factors with quarter-point elements.”Int. J. Fracture, 32(2), 127–140.
3.
Barsoum, R. S.(1976). “On the use of isoparametric finite elements in linear fracture mechanics.”Int. J. Numerical Methods in Engrg., 10(1), 25–37.
4.
Bathe, K. J. (1982). Finite element procedures in engineering analysis . Prentice-Hall, Inc., Englewood Cliffs, N.J.
5.
Bresler, B., and Scordelis, A. C. (1961). “Shear strength of reinforced concrete beams.”Struct. and Mat. Res., Ser. 100, Issue 13(SESM 61-13), Dept. of Civ. Engrg., Inst. of Engrg. Res., Univ. of California, Berkeley, Calif.
6.
Broek, D. (1987). Elementary engineering fracture mechanics . Martinus Nijhoff Publishers, Dordrecht, The Netherlands.
7.
Chan, S. K., Tuba, I. S., and Wilson, W. K.(1970). “On the finite element method in linear fracture mechanics.”Engrg. Fracture Mech., 2(1), 1–17.
8.
Cheng, S., and Zhang, X.(1990). “Generalized stiffness derivative method for mixed mode crack problems.”Mech. Res. Communications, 17(6), 437–444.
9.
Erdogan, F., and Sih, G. C.(1963). “On the crack extension in plate under in plane loading and transverse shear.”J. Basic Engrg., 85(4), 519–527.
10.
Gerstle, W. H. (1982). “The fracture mechanics of bond in reinforced concrete,” MSc thesis, Dept. of Struct. Engrg., Cornell Univ., Ithaca, N.Y.
11.
Gerstle, W. H. (1986). “Finite and boundary element modeling of crack propagation in two- and three-dimensions using interactive computer graphics,” PhD thesis, Dept. of Struct. Engrg., Cornell University, Ithaca, N.Y.
12.
Gerstle, W. H., and Abdalla, J. E. (1990). “Finite element meshing criteria for crack problems.”STP 1074-1990, ASTM, Philadelphia, Pa., 509–521.
13.
Gerstle, W. H., Xie, M., Panthaki, M. J., Labreche, D. A., and Christian-Frear, T. L. (1991). “CoMeT: an integrated computer graphical structural zooming system.”Rep., PSI0410, RE/SPEC Inc., Albuquerque, N.M.
14.
Gerstle, W. H., and Xie, M.(1992). “FEM modeling of fictitious crack propagation in concrete.”J. Engrg. Mech., ASCE, 118(2), 416–434.
15.
Hellen, T. K.(1975). “On the method of virtual crack extensions.”Int. J. Numerical Methods in Engrg., 9(1), 187–207.
16.
Henshell, R. D., and Shaw, K. G.(1975). “Crack tip finite elements are unnecessary.”Int. J. Numerical Methods in Engrg., 9(3), 495–507.
17.
Hillerborg, A. (1985). “Numerical methods to simulate softening and fracture of concrete.”Fracture mechanics of concrete: structural application and numerical calculation, G. Sih and A. DiTommaso, eds., Martinus Nijhoff Publishers, Dordrecht, The Netherlands, 141–170.
18.
Hillerborg, A., Modeer, M., and Petersson, P. E.(1976). “Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements.”Cement, Concrete Res., 6(6), 773–782.
19.
Hussain, M. A., Pu, S. L., and Underwood, J. H. (1974). “Strain energy release rate for a crack under combined mode I and mode II.”Fracture Analy., STP 560, ASTM, Philadelphia, Pa.
20.
Ingraffea, A. R. (1981). “Mixed-mode fracture initiation in Indiana limestone and westerly granite.”Proc., 22nd U.S. Symp. on Rock Mech., Rock Mech. from Res. to Application, MIT Press, Cambridge, Mass., 186–191.
21.
Ingraffea, A. R., Gerstle, W. H., Gergely, P., and Saouma, V.(1984). “Fracture mechanics of bond in reinforced concrete.”J. Struct. Engrg., ASCE, 110(4), 871–890.
22.
Ingraffea, A. R., and Gerstle, W. H. (1984). “Nonlinear fracture models for discrete crack propagation.”Proc., NATO Advanced Workshop on Application of Fracture Mech. to Cementitious Composites, S. P. Shah, ed. Martinus Nijhoff, Hingham, Mass.
23.
Ingraffea, A. R., and Saouma, V. (1985). “Numerical modeling of discrete crack propagation in reinforced and plain concrete.”Fracture mechanics of concrete: structural application and numerical calculation, G. Sih and A. DiTommaso, eds., Martinus Nijhoff Publishers, Dordrecht, The Netherlands, 171–225.
24.
Ishikawa, H. (1980). “A finite element analysis of stress intensity factors for combined tensile and shear loading by only a virtual crack extension.”Int. J. Fracture, 16(5), R243–246.
25.
Ishikawa, H., Kitagawa, H., and Okamura, H. (1979). “J integral of a mixed mode crack and its application.” Proc., 3rd Int. Conf. on Mech. Behavior of Mat., Vol. 3, 447–455.
26.
Lynn, P. P., and Ingraffea, A. R.(1978). “Transition elements to be used with quarter-point crack tip elements.”Int. J. Numerical Methods in Engrg., 12(6), 1031–1036.
27.
Melin, S.(1987). “Fracture from a straight crack subjected to mixed mode loading.”Int. J. Fracture, 32(4), 257–263.
28.
Parks, D. M.(1974). “A stiffness derivative finite element technique for determination of crack tip stress intensity factors.”Int. J. Fracture, 10(4), 487–502.
29.
Petersson, P. E. (1981). “Crack growth and development of fracture zone in plain concrete and similar materials.”Rep. TVBM-1006, Lund Inst. of Tech., Lund, Sweden.
30.
Rots, J. G. (1988). “Computational modeling of concrete fracture,” PhD dissertation, Delft Univ. of Technol., Dept. of Civ. Engrg., Delft, The Netherlands.
31.
Rots, J. G., and de Borst, R. (1987). “Mixed mode crack propagation and fracture in concrete.”J. Engrg. Mech., ASCE,Vol. 113(11), 1739–1758.
32.
Saouma, V. E., and Schwemmer, D.(1984). “Numerical evaluation of the quarter-point crack tip element.”Int. J. Numerical Methods in Engrg., 20(9), 1629–1641.
33.
Saouma, V. E., and Zatz, I. J.(1984). “An automated finite element procedure for fatigue crack propagation analysis.”Engrg. Fracture Mech., 20(2), 321–333.
34.
Sha, G. T. (1984). “On the virtual crack extension technique for stress intensity factors and energy release rate calculations for mixed fracture mode.”Int. J. Fracture, 25(2), R33–R42.
35.
Sha, G. T., and Yang, C. T.(1990). “Use of analytically decoupled near-tip displacement solutions for calculating the decoupled weight functions of mixed fracture modes.”Engrg. Fracture Mech., 37(3), 591–610.
36.
Shih, C. F., deLorenzi, H. G., and German, M. D.(1976). “Crack extension modeling with singular quadratic elements.”Int. J. Fracture, 12(4), 647–651.
37.
Sih, G. C.(1974). “Strain-energy-density factor applied to mixed-mode crack problems.”Int. J. Fracture, 10(3), 305–321.
38.
Swenson, D. V., and Ingraffea, A. R.(1988). “Modeling mixed-mode dynamic crack propagation using finite elements: theory and applications.”Computational Mech., 3(2), 381–397.
39.
Tada, H., Paris, P., and Irwin, G. (1973). The stress analysis of cracks handbook. Del Res. Corp., Hellertown, Penn.
40.
Tracey, D. J.(1971). “Finite element for determination of crack tip elastic stress intensity factors.”Engrg. Fracture Mech., 3(3), 255–265.
41.
Wawrzynek, P. A. (1986). “Interactive finite element analysis of fracture processes: an integrated approach,” MSc thesis, Dept. of Struct. Engrg., Cornell Univ., Ithaca, N.Y.
42.
Wawrzynek, P. A., and Ingraffea, A. R. (1986). “Local remeshing around a propagating crack tip using interactive computer graphics.”Finite element method, modeling, and new applications; Proc., ASME PVP Conf., Vol. 1, E. M. Patten et al. eds., Am. Soc. of Mech. Engrs. (ASME), New York, N.Y.
43.
Xie, M., Gerstle, W. H., and Panthaki, M. (1990). “Fracture analysis of cementitious seals for nuclear waste isolation.”Fracture behavior and design of materials and structures, D. Firrao, ed., Engrg. Mat. Advisor Services, Ltd., Warley, West Midlands, U. K., 786–791.
Information & Authors
Information
Published In
Journal of Engineering Mechanics
Volume 121 • Issue 8 • August 1995
Pages: 914 - 923
Copyright
Copyright © 1995 American Society of Civil Engineers.
History
Published online: Aug 1, 1995
Published in print: Aug 1995
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.