Out‐of‐Plane Buckling of Restrained Thin Rings of General Open Section
Publication: Journal of Engineering Mechanics
Volume 120, Issue 5
Abstract
This paper describes a closed‐form solution based on thin‐walled member theory for the out‐of‐plane buckling of thin rings of an open cross section. The theory considers the practical features of restraint and loading conditions of rings situated at axisymmetric shell intersections, and it is applicable to any thin‐walled open‐section form. Numerical comparisons between the closed‐form solution and a finite‐element shell buckling analysis are then presented to demonstrate the accuracy of the closed‐form solution, and to study the effects on the buckling behavior of angle section rings of various parameters, including the ring width‐to‐thickness ratio, the load position, the restraint position, and the flange size. The effect of secondary warping on the buckling behavior of angle section rings is also discussed in some detail. Finally, a simple expression for use in design is established for the buckling strength of an angle section ring loaded and supported at its inner edge.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Attard, M. M. (1988). “Effect of secondary warping on lateral buckling.” Proc. 11th Australasian Conf. Mech. of Struct. Mat., Auckland, New Zealand, 219–225.
2.
Boresi, A. (1955). “A refinement of the theory of buckling of rings under uniform pressure.” J. Appl. Mech., 22(1), 95–102.
3.
Cheney, J. A. (1963). “Bending and buckling of thin‐walled open section rings.” J. Engrg. Mech. Div., ASCE, 89(5), 17–34.
4.
Goldberg, J. E., and Bogdanoff, J. L. (1962). “Out‐of‐plane buckling of I‐section rings.” Publications, Int. Assoc. Bridges and Struct. Engrg., 22, 73–92.
5.
Lucas, R. M. (1992) “Flexural‐torsional buckling of restrained rings of general cross‐section,” B. E. thesis, James Cook Univ., Townsville, Australia.
6.
Rotter, J. M., and Jumikis, P. T. (1988). “Non‐linear strain‐displacement relations for thin shells of revolution,” Research Report R563, School of Civ. and Mining Engrg., Univ. of Sydney, Sydney, Australia.
7.
Smith, C. V. Jr., and Simitses, G. J. (1969). “Effect of shear and load behavior on ring stability,” J. Engrg. Mech. Div., ASCE, 95(3), 559–569.
8.
Teng, J. G., and Rotter, J. M. (1985). “Out‐of‐plane buckling of restrained monosymmetric rings,” Res. Rep. R510, School of Civ. and Mining Engrg., Univ. of Sydney, Sydney, Australia.
9.
Teng, J. G., and Rotter, J. M. (1987). “Unrestrained out‐of‐plane buckling of monosymmetric rings,” J. Constr. Steel Res., 7, 451–471.
10.
Teng, J. G., and Rotter, J. M. (1988). “Buckling of restrained monosymmetric rings.” J. Engrg. Mech., ASCE, 114(10), 1651–1671.
11.
Teng, J. G., and Rotter, J. M. (1989). “Non‐symmetric bifurcation of geometrically non‐linear elastic‐plastic axisymmetric shells subject to combined loads including torsion.” Comp. and Struct., 32(2), 453–477.
12.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability. 2nd ed., McGraw‐Hill, New York, N.Y.
13.
Trahair, N. S., and Papangelis, J. P. (1987). “Flexural‐torsional buckling of monosymmetric arches.” J. Struct. Engrg., ASCE, 113(10), 2271–2288.
14.
Wah, T. (1967). “Buckling of thin circular rings under uniform pressure.” Int. J. Solids and Struct., 3, 967–974.
Information & Authors
Information
Published In
Copyright
Copyright © 1994 American Society of Civil Engineers.
History
Received: Feb 3, 1993
Published online: May 1, 1994
Published in print: May 1994
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.