Uniaxial Model for Concrete under Variable Temperature and Stress
Publication: Journal of Engineering Mechanics
Volume 119, Issue 8
Abstract
A plasticity model using a strain‐rate formulation is presented to describe the uniaxial response of concrete when subjected to combined thermal and mechanical actions. The total strain rate is resolved into three individual components: mechanical strain, thermal strain, and transient creep strain. Each component is formulated individually. The mechanical strain rate is assumed to consist of an elastic strain rate and a plastic strain rate, which itself is taken as temperature‐dependent. In describing the plastic strain rate, the nonlinear part of the uniaxial stress‐strain curves is assumed to be a quarter of ellipse, defined for a given temperature in the range 20°C–800°C. The model was first used to analyze uniaxial (experimental) data under variable load but isothermal conditions, and then to investigate the effect of a sustained load on the deformational response of a concrete specimen under heating. Thirdly, a set of experimental relaxation tests was studied, in which temperature and stress vary continuously under a zero total strain condition. Here, the importance of a variable temperature and stress, and the significance of the history, is demonstrated.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Abrams, M. S. (1971). “Compressive strength of concrete at temperature up to 1600°F.” ACI Spec. Publ. No. 25, American Concrete Inst., Detroit, Mich., 33–58.
2.
Ahmad, S. H., and Hamoush, S. (1988). “A constitutive model for concrete exposed to high temperatures.” Elastic Plastic Failure Modelling of Structures with Applications. ASME Pressure Vessels and Piping Conference, American Society of Mechanical Engineers, New York, N.Y., 145–152.
3.
Anderberg, Y., and Thelandersson, S. (1976). “Stress and deformation characteristics of concrete at high temperatures: 2. experimental investigation and material behaviour model.” Bull. 54, Lund Institute of Technology, Lund, Sweden.
4.
De Borst, R., and Peeters, P. P. J. M. (1989). “Analysis of concrete structures under thermal loading.” Comp. Meth. Appl. Mech. Engrg., 77, 293–310.
5.
Ehm, C., and Schneider, U. (1985). “The high temperature behaviour of concrete under biaxial conditions.” Cem. Concr. Res., 15(1), 27–34.
6.
Khennane, A. (1992). “Mathematical models for the behaviour of concrete at elevated temperatures,” PhD thesis, Univ. of Queensland, Brisbane, Australia.
7.
Khennane, A., and Baker, G. (1989). “A uniaxial model for the thermo‐mechanical behaviour of concrete at elevated temperatures.” Civil Engrg. Res. Report, No. CE 104, Univ. of Queensland, Brisbane, Australia.
8.
Khennane, A., and Baker, G. (1992). “Plasticity models for the biaxial behaviour of concrete at elevated temperatures. Part I: Failure criterion.” Comp. Methods Appl. Mech. Engrg. 100, 207–223.
9.
Khennane, A., and Baker, G. (1992). “Plasticity models for the biaxial behaviour of concrete at elevated temperatures. Part II: Implementation and simulation tests.” Comp. Methods Appl. Mech. Engrg., 100, 225–248.
10.
Kordina, K., Ehm, C., and Schneider, U. (1986). “Effect of biaxial loading on the high temperature behaviour of concrete.” 1st Int. Symp. on Fire Safety Sci., Hemisphere Publ. Corp., Washington, D.C., 281–291.
11.
Khoury, A. G., Grainger, B. N., and Sullivan, P. J. E. (1985). “Transient thermal strain of concrete: Literature Review. Conditions within Specimen and Behaviour of Individual Constituents.” Mag. Conc. Res., 37(132), 131–144.
12.
Lin, F. B., Bažant, Z. P., Chern, J. C., and Marchertas, A. H. (1987). “Concrete model with normality and sequential identification.” Comp. Struct., 26(6), 1011–1025.
13.
Schneider, U., Diederichs, U., and Ehm, C. (1981). “Effect of temperature on steel and concrete for PCRV's.” Nucl. Engrg. and Design, 245–258.
14.
Schneider, U. (1982). “Behaviour of concrete at high temperatures.” Deutscher Ausschus fur Stahlbeton, Heft 337, W. Ernst und Sohn, Berlin.
15.
Thelandersson, S. (1982). “On the multiaxial behaviour of concrete exposed to high temperatures.” Nucl. Engrg. and Design, 75, 271–282.
16.
Thelandersson, S. (1987). “Modeling of combined thermal and mechanical action in concrete.” J. Engrg. Mech., ASCE, 113(6), 893–906.
Information & Authors
Information
Published In
Copyright
Copyright © 1993 American Society of Civil Engineers.
History
Received: Feb 4, 1992
Published online: Aug 1, 1993
Published in print: Aug 1993
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.