Study of Size Effect in Concrete Using Fictitious Crack Model
Publication: Journal of Engineering Mechanics
Volume 117, Issue 7
Abstract
A boundary element program based on a fictitious crack‐model (FCM) was used to study the size effect in concrete during mode‐I nonlinear fracturing. Series of numerical parametric studies were performed to examine the effects of specimen size, loading configuration (three‐point beam and double cantilever beam), and initial notch size on the nonlinear fracture characteristics. The results of numerical simulations confirmed the curve‐fitting procedure proposed by Bažant and his coworkers in their size‐effect law method. However, two notable exceptions were observed: (1) Small size specimens where bending strengthening may be pronounced; and (2) specimens with small initial notch. In addition to examining the range of applicability of Bažant's size‐effect law method, this paper provides empirical equations for determination of the maximum process‐zone length under three‐point bending or double cantilever beam (DCB) loading condition. Finally, the normalized R‐curves expressed in terms of the energy release rate versus the normalized effective crack extension have been shown to be independent of specimen size, initial notch size, and loading configurations. Therefore, the normalized R‐curves are recommended as a proper way of representing the nonlinear resistance of beam structures to mode‐I fracture.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Atkins, A. G., and Mai, Y. W. (1985). Elastic and plastic fracture. Ellis Horwood Ltd., New York, N.Y., 652–660.
2.
Bažant, Z. P. (1976). “Instability, ductility and size effect in strain‐softening concrete.” J. Engrg. Mech. Div., ASCE, 102(2), 331–344.
3.
Bažant, Z. P. (1984). “Size effect in blunt fracture: Concrete, rock, metal.” J. Engrg. Mech., ASCE, 110(4), 518–535.
4.
Bažant, Z. P. (1989). “Fracture energy of heterogeneous materials and similitude.” SEM/RILEM Int. Conf. on Fracture of Concrete and Rock, S. P. Shah and S. E. Swartz, eds., 229–241.
5.
Bažant, Z. P., and Cedolin, L. (1984). “Approximate linear analysis of concrete fracture by R‐curves.” J. Engrg. Mech., ASCE, 110(6), 1336–1355.
6.
Bažant, Z. P., Gettu, R., and Kazemi, M. T. (1989). “Identification of nonlinear fracture properties from size effect tests and structural analysis based on geometrydependent R‐curves.” Report No. 89‐3, Ctr. for Advanced Cement‐Based Materials, Northwestern Univ., Evanston, Ill.
7.
Bažant, Z. P., Kim, J., and Pfeiffer, P. A. (1986). “Nonlinear fracture properties from size effect tests.” J. Struct. Engrg., ASCE, 112(2), 289–307.
8.
Bažant, Z. P., and Oh, B. H. (1981). “Concrete fracture viz. stress‐strain relations.” Report 81‐101665C, Ctr. for Concrete and Geomaterials, Northwestern Univ., Evanston, Ill.
9.
Bažant, Z. P., and Pfeiffer, P. A. (1986). “Shear fracture tests of concrete.” Mater. Struct., 19(2), 110–121.
10.
Bažant, Z. P., and Pfeiffer, P. A. (1987). “Determination of fracture energy form size effect and brittleness number.” ACI Mater. J., 84(6), 463–480.
11.
Bažant, Z. P., and Prat, P. C. (1988). “Measurement of mode III fracture energy of concrete.” Nucl. Engrg. and Des., 106(1), 1–8.
12.
Broek, D. (1986). Elementary engineering fracture mechanics. 4th Ed., Martinus Nijhoff Publishers, Dordrecht, the Netherlands.
13.
Carpinteri, A., and Sih, G. C. (1984). “Damage accumulation and crack growth in bilinear materials with softening.” Theor. Appl. Fract. Mech., 1(2), 145–159.
14.
Dougdale, D. S. (1960). “Yielding of steel sheets containing slits.” J. Mech. Phys. Solids, 8(2), 100–108.
15.
Foote, R., Mai, Y.‐W., and Cotterell, B. (1986). “Crack growth resistance curve in strain softening materials.” J. Mech. Phys. Solids, 34(6), 593–607.
16.
Gerstle, W. H., Ingraffea, A. R., and Gergely, P. (1982). “The fracture mechanics of bond in reinforced concrete.” Report 82‐7, Dept. of Civ. Engrg., Cornell Univ., Ithaca, N.Y.
17.
Hillerborg, A. (1985a). “A comparison between the size effect law and the fictitious crack model.” ia Dei Poli anniversary volume, L. Cedolin, ed., Politecnico di Milano, 331–334.
18.
Hillerborg, A. (1985b). “Numerical methods to simulate softening and fracture of concrete.” Fracture mechanics concrete: Structural application and numerical calculation, G. C. Sih and A. Di'Tomaso, eds., Martinus Nijhoff Publisher, Dordrecht, the Netherlands, 141–170.
19.
Hillerborg, A., Modeer, M., and Peterson, P. E. (1976). “Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements.” Cem. Concr. Res., 6(6), 773–782.
20.
Jenq, Y. S., and Shah, S. P. (1985a). “A fracture toughness criterion for concrete.” Engrg. Fract. Mech., 21(5), 1055–1069.
21.
Jenq, Y. S., and Shah, S. P. (1985b). “A two parameter fracture model for concrete.” J. Engrg. Mech. Div., ASCE, 111(4), 1227–1241.
22.
Li, V. C., and Liang, E. (1985). “Fracture process in concrete and fiber‐reinforced cementitious composites.” J. Engrg. Mech., ASCE, 112(6), 566–586.
23.
Liang, R. Y., and Li, Y. N. (1991). “Simulations of nonlinear fracture process zone in cementitious materials—A boundary element approach.” Comput. Mech., 7(4).
24.
Mindess, S., Lawrence, F. V., and Kesler, C. E. (1977). “The J‐integral as a fracture criterion for fiber reinforced concrete.” Cem. Concr. Res., 7, 731–742.
Information & Authors
Information
Published In
Journal of Engineering Mechanics
Volume 117 • Issue 7 • July 1991
Pages: 1631 - 1651
Copyright
Copyright © 1991 ASCE.
History
Published online: Jul 1, 1991
Published in print: Jul 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.