Bending Performance of Cold-Formed Thick-Walled Rectangular Steel Beams
Publication: Journal of Structural Engineering
Volume 150, Issue 12
Abstract
An increasing number of cold-formed thick-walled members are being employed in engineering structures. However, research on their bending performance is still lacking, and existing codes are primarily suitable for thin-walled steel members. Therefore, bending tests were conducted on 10 cold-formed thick-walled rectangular beams. The primary test parameters were the width, height, and thickness of the cross section. The material properties, initial geometric imperfections, failure modes, load–deflection curves, ultimate loads, rotation capacities, and load–strain curves of these beams were analyzed. Subsequently, a nonlinear finite-element (FE) model of cold-formed thick-walled rectangular beams was developed. After validating the numerical model with the test results, a parametric study was conducted. The results revealed that the height-to-width, radius-to-thickness, and width-to-thickness ratios significantly affected the plastic development ability of the cross section. With the increase in height-to-width and radius-to-thickness ratios, an existing Chinese design code yielded unsafe limits for the width-to-thickness ratio. Based on the parametric study results, width-to-thickness ratio limits suitable for cold-formed thick-walled cross sections were recommended. Finally, a simplified design method for the bending resistance of cold-formed thick-walled rectangular beams was proposed and validated using experimental and FE model results.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors express their sincere gratitude for the financial support provided by the National Natural Science Foundation of China (No. 52192663), the National Key R&D Program of China (No. 2018YFC0705503), Chongqing Municipal Construction Science and Technology Plan Project (City SciTech No. 2022-5-6), and the Fundamental Research Funds for the Central Universities (No. 2023CDJXY-032).
References
ABAQUS. 2012. ABAQUS user’s manual, version 6.12. Providence, RI: Dassault Systèmes Simulia.
Abdel-Rahman, N., and K. S. Sivakumaran. 1997. “Material properties model for analysis of cold-formed steel members.” J. Struct. Eng. 123 (9): 1135–1143. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:9(1135).
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. AISI S100-16. Washington, DC: AISI.
Ashraf, M., L. Gardner, and D. A. Nethercot. 2008. “Structural stainless steel design: Resistance based on deformation capacity.” J. Struct. Eng. 134 (3): 402–411. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:3(402).
CEN (European Committee for Standardization).2006. Eurocode 3: Design of steel structures: Part 1-1: general rules and rules for buildings. EN 1993-1-1. Brussels, Belgium: CEN.
Chinese Standard. 2002. Technical code of cold-formed thin-walled steel structures. GB 50018-2002. Beijing: Chinese Standard Press.
Chinese Standard. 2018a. Cold forming hollow sectional steel for general structure. GB/T 6728-2017. Beijing: Chinese Standard Press.
Chinese Standard. 2018b. Standard for design of steel structures. GB 50017-2017. Beijin: China Architecture & Building Press.
D’Aniello, M., E. M. Gueneyisi, R. Landolfo, and K. Mermerdaş. 2014. “Analytical prediction of available rotation capacity of cold-formed rectangular and square hollow section beams.” Thin-Walled Struct. 77 (Apr): 141–152. https://doi.org/10.1016/j.tws.2013.09.015.
Gardner, L., N. Saari, and F. Wang. 2010. “Comparative experimental study of hot-rolled and cold-formed rectangular hollow sections.” Thin-Walled Struct. 48 (7): 495–507. https://doi.org/10.1016/j.tws.2010.02.003.
Gardner, L., and X. Yun. 2018. “Description of stress-strain curves for cold-formed steels.” Constr. Build. Mater. 189 (Nov): 527–538. https://doi.org/10.1016/j.conbuildmat.2018.08.195.
Guo, Y. J., A. Z. Zhu, Y. L. Pi, and F. Tin-Loi. 2007. “Experimental study on compressive strengths of thick-walled cold-formed sections.” J. Constr. Steel Res. 63 (5): 718–723. https://doi.org/10.1016/j.jcsr.2006.08.008.
Ho, G., L. W. Tong, Y. Y. Chen, and Z. G. Li. 2013. “Testing and analysis model for material property of non-thin-walled cold-formed square hollow sections.” [In Chinese.] Eng. Mech. 30 (2): 372–378. https://doi.org/10.6052/j.issn.1000-4750.2011.08.0559.
Hu, S. D., B. Ye, and L. X. Li. 2011. “Materials properties of thick-wall cold-rolled welded tube with a rectangular or square hollow section.” Constr. Build. Mater. 25 (5): 2683–2689. https://doi.org/10.1016/j.conbuildmat.2010.12.019.
Huang, Y., and B. Young. 2018. “Structural performance of cold-formed lean duplex stainless steel beams at elevated temperatures.” Thin-Walled Struct. 129 (Aug): 20–27. https://doi.org/10.1016/j.tws.2018.03.031.
Li, G. W., and Y. Q. Li. 2018. “Overall stability behavior of axially compressed cold-formed thick-walled steel tubes.” Thin-Walled Struct. 125 (Apr): 234–244. https://doi.org/10.1016/j.tws.2018.01.032.
Li, G. W., Y. Q. Li, J. Xu, and X. Cao. 2019. “Experimental investigation on the longitudinal residual stress of cold-formed thick-walled SHS and RHS steel tubes.” Thin-Walled Struct. 138 (May): 473–484. https://doi.org/10.1016/j.tws.2018.09.036.
Li, H. T., and B. Young. 2019. “Cold-formed high strength steel SHS and RHS beams at elevated temperatures.” J. Constr. Steel Res. 158 (Jul): 475–485. https://doi.org/10.1016/j.jcsr.2019.03.034.
Li, Y. Q., G. W. Li, Z. Y. Shen, Y. F. Ma, and S. W. Zhu. 2015. “Modification method for yield strength of cold-formed thick-walled steel sections considering cold-forming effect.” [In Chinese.] J. Build. Struct. 36 (5): 1–7. https://doi.org/10.14006/j.jzjgxb.2015.05.001.
Liu, D. Y., H. B. Liu, Z. H. Chen, and X. W. Liao. 2017. “Structural behavior of extreme thick-walled cold-formed square steel columns.” J. Constr. Steel Res. 128 (Jan): 371–379. https://doi.org/10.1016/j.jcsr.2016.09.004.
Liu, Z. A., H. B. Liu, Z. H. Chen, and G. P. Zhang. 2018. “Structural behavior of cold-formed thick-walled rectangular steel columns.” J. Constr. Steel Res. 147 (Aug): 277–292. https://doi.org/10.1016/j.jcsr.2018.03.013.
Ma, J. L., T. M. Chan, and B. Young. 2016. “Experimental investigation of cold-formed high strength steel tubular beams.” Eng. Struct. 126 (Nov): 200–209. https://doi.org/10.1016/j.engstruct.2016.07.027.
Ma, J. L., T. M. Chan, and B. Young. 2017. “Design of cold-formed high strength steel tubular beams.” Eng. Struct. 151 (Nov): 432–443. https://doi.org/10.1016/j.engstruct.2017.08.002.
Men, P. F., J. Di, F. J. Qin, E. Z. Lin, J. Wang, and X. Peng. 2024. “Experimental investigation on axial compression behaviour of cold-formed thick-walled steel tubes.” J. Constr. Steel Res. 214 (Mar): 108431. https://doi.org/10.1016/j.jcsr.2023.108431.
Men, P. F., J. Di, F. J. Qin, and Y. Su. 2023. “Experimental investigation of the shear behaviour of slender continuous steel–concrete composite girders in hogging moment.” J. Struct. Eng. 149 (1): 04022218. https://doi.org/10.1061/JSENDH.STENG-11537.
Rasmussen, K. J. R., and G. J. Hancock. 1993. “Design of cold-formed stainless steel tubular members. II: Beams.” J. Struct. Eng. 119 (8): 2368–2386. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:8(2368).
Schafer, B. W., and T. Peköz. 1998. “Direct strength prediction of cold-formed steel members using numerical elastic buckling solutions.” In Proc., 14th Int. Specialty Conf. on Cold-Formed Steel Structures. Rolla, MO: Univ. of Missouri.
Shi, Y., X. H. Zhou, T. T. Gao, and Y. Guan. 2015. “Research on flexural capacity of cold-formed steel double limbs built-up box beams.” [In Chinese.] J. Build. Struct. 36 (11): 20–28. https://doi.org/10.14006/j.jzjgxb.2015.11.003.
Tong, L. W., G. Hou, Y. Y. Chen, F. Zhou, K. Shen, and A. A. Yang. 2012. “Experimental investigation on longitudinal residual stresses for cold-formed thick-walled square hollow sections.” J. Constr. Steel Res. 73 (Jun): 105–116. https://doi.org/10.1016/j.jcsr.2012.02.004.
Von Kármán, T., E. E. Sechler, and L. H. Donnell. 1932. “The strength of thin plates in compression.” Trans. ASME. 54 (2): 53–56. https://doi.org/10.1115/1.4021738.
Wilkinson, T. 1999. “The plastic behaviour of cold-formed rectangular hollow sections.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Sydney.
Wilkinson, T., and G. Hancock. 2002. “Predicting the rotation capacity of cold-formed RHS beams using finite element analysis.” J. Constr. Steel Res. 58 (11): 1455–1471. https://doi.org/10.1016/S0143-974X(02)00006-8.
Yun, X., and L. Gardner. 2018. “The continuous strength method for the design of cold-formed steel non-slender tubular cross-sections.” Eng. Struct. 175 (Nov): 549–564. https://doi.org/10.1016/j.engstruct.2018.08.070.
Zhao, O., B. Rossi, L. Gardner, and B. Young. 2015. “Behaviour of structural stainless steel cross-sections under combined loading—Part II: Numerical modelling and design approach.” Eng. Struct. 89 (Apr): 247–259. https://doi.org/10.1016/j.engstruct.2014.11.016.
Zhou, X. H., Y. Guan, T. T. Gao, and Y. Shi. 2016. “Study on flexural capacity of cold-formed steel double-limb built-up I-shape beams.” China Civ. Eng. J. 49 (8): 16–27.
Zou, Y., K. D. Zheng, Z. X. Zhou, Z. Y. Zhang, J. C. Guo, and J. L. Jiang. 2023. “Experimental study on flexural behavior of hollow steel-UHPC composite bridge deck.” Eng. Struct. 274 (Jan): 115087. https://doi.org/10.1016/j.engstruct.2022.115087.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Sep 27, 2023
Accepted: Jun 25, 2024
Published online: Sep 23, 2024
Published in print: Dec 1, 2024
Discussion open until: Feb 23, 2025
ASCE Technical Topics:
- Analysis (by type)
- Beams
- Bending (structural)
- Cold-formed steel
- Continuum mechanics
- Dynamics (solid mechanics)
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Failure loads
- Finite element method
- Materials engineering
- Metals (material)
- Methodology (by type)
- Numerical analysis
- Numerical methods
- Solid mechanics
- Static loads
- Statics (mechanics)
- Steel
- Steel beams
- Structural analysis
- Structural dynamics
- Structural engineering
- Structural members
- Structural systems
- Walls
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.