Simulation-Based Fracture Assessment of Seismic Moment Frame Connections with Box Columns
Publication: Journal of Structural Engineering
Volume 150, Issue 5
Abstract
Welded connections between beams and built-up box columns in steel moment frames require the attachment of continuity plates to the inside of the column using complete-joint-penetration (CJP) groove welds. Electroslag welding (ESW) is often used to weld at least one of the four sides of each continuity plate to the inside of the box column. These welds are susceptible to fracture due to decreased material toughness and installation of containment plates that create a notch condition. Finite-element simulations are presented to examine the effect of design and detailing parameters on the fracture of these connections, as assessed through conventional fracture mechanics as well as continuum damage mechanics. The results indicate that improved bevel details in the containment plate and reduced beam section (RBS) connections strongly mitigate fracture demands, whereas both eccentricity in the weld with respect to the continuity plate and unequal beam and column flange widths exacerbate demands. The beam and column size, as well as beam web weld access hole details, have only a modest effect on the demands. Simulations are also conducted to examine column-wall thickness limits beyond which continuity plates may not be required. These suggest that limits similar to those specified for wide-flanged columns may not provide adequate performance. Limitations of the study are presented, along with directions for future work.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors acknowledge support from the National Science Foundation (Grant No. CMMI 2129445). The authors are also thankful to Professor Michael Engelhardt of the University of Texas, Austin, for his constructive advice. The views and findings presented in this article are entirely of the authors.
References
AISC. 2022a. Prequalified connections for special and intermediate steel moment frames for seismic applications. AISC 358-22. Chicago: AISC.
AISC. 2022b. Seismic provisions for structural steel buildings. AISC 341-22. Chicago: AISC.
AISC. 2022c. Specification for structural steel buildings. AISC 360-22. Chicago: AISC.
AWS (American Welding Society). 2016. Structural welding code–seismic supplement. AWS D1.8/D1.8M. Doral, FL: AWS.
Barsom, J. M., and S. T. Rolfe. 1999. Fracture and fatigue control in structures: Applications of fracture mechanics. West Conshohocken, PA: ASTM.
Berdin, C., and J. Besson. 2004. Local approach to fracture. Paris: Les Presses de Ecole des Mines.
Beremin, F., A. Pineau, F. Mudry, J. C. Devaux, Y. D’Escatha, and P. Ledermann. 1983. “A local criterion for cleavage fracture of a nuclear pressure vessel steel.” Metall. Trans. A 14 (11): 2277–2287. https://doi.org/10.1007/BF02663302.
Chen, C. C., C. L. Lai, and K. C. Lin. 2009. “Finite element analysis of electro-slag welding for diaphragms in steel box column.” In Proc., 11th Taiwan-Korea-Japan Joint Seminar on Earthquake Engineering for Building Structures SEEBUS 2009, Kyoto, Japan: The Japan-Korea-Taiwan Joint Seminar on Earthquake Engineering for Building Structures.
Chen, C. H., K. C. Lin, S. J. Jhuang, and H. Y. Chang. 2020. “Seismic performance evaluation of steel box-column connections with ESW stiffeners.” Int. J. Steel Struct. 20 (Jun): 776. https://doi.org/10.1007/s13296-020-00321-9.
Chi, W. M., G. G. Deierlein, and A. Ingraffea. 2000. “Fracture toughness demands in welded beam-column moment connections.” J. Struct. Eng. 126 (1): 88–97. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:1(88).
Elkady, A., and D. G. Lignos. 2018. “Improved seismic design and nonlinear modeling recommendations for wide-flange steel columns.” J. Struct. Eng. 144 (9): 04018162. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002166.
Frederick, C. O., and P. J. Armstrong. 1966. A mathematical representation of the multiaxial bauschinger effect. Berkeley, UK: Berkeley Nuclear Laboratories.
Gilmer, H. 2005. “Implementation of narrow-gap improved electroslag welding for bridge fabrication.” In Proc., World Steel Bridge Symp. Conf. Proc., 2005. Chicago: American Institute of Steel Construction.
Jhunjhunwala, A., and A. M. Kanvinde. 2023. “Fracture mechanics based fragility assessment of pre-Northridge welded column splices.” J. Struct. Eng. 149 (6): 04023062. https://doi.org/10.1061/JSENDH.STENG-11749.
JSSC (Japanese Society of Steel Construction). 2016. Guide book to prevent brittle fracture at an electroslag weld on the inner diaphragm. Tokyo: Japanese Society of Steel Construction.
Kanvinde, A. M., and G. G. Deierlein. 2007. “A cyclic void growth model to assess ductile fracture in structural steels due to ultra low cycle fatigue.” J. Eng. Mech. 133 (6): 701–712. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:6(701).
Kanvinde, A. M., B. V. Fell, I. R. Gomez, and M. Roberts. 2008. “Predicting fracture in structural fillet welds using traditional and micromechanics-based models.” Eng. Struct. 30 (11): 3325–3335. https://doi.org/10.1016/j.engstruct.2008.05.014.
Lin, K. C., and S. J. Jhuang. 2010. “Seismic behaviors and design method on steel beam-to-box column connections with cover plate.” [In Chinese.] Struct. Eng. 25 (2): 75–92.
Lin, R. S., H. Y. Chung, and M. H. Lin. 2012. “Analysis and improvement for the inherent backing-bar crack problem of electrogas and electroslag welding in box-columns.” [In Chinese.] J. Chin. Inst. Civ. Hydraul. Eng. 24 (2): 169–183.
McMeeking, R. M., and D. M. Parks. 1979. On criteria for J-dominance of crack-tip fields in large scale yielding. ASTM STP 668. West Conshohocken, PA: ASTM.
Myers, A. T., G. Deierlein, and A. M. Kanvinde. 2009. Testing and probabilistic simulation of ductile fracture initiation in structural steel components and weldments. Stanford, CA: Stanford Univ.
Myers, A. T., A. M. Kanvinde, and G. Deierlein. 2010. “Calibration of the SMCS criterion for ductile fracture in steels: Specimen size dependence and parameter assessment.” J. Eng. Mech. 136 (11): 1401–1410. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000178.
Ozkula, G., R. Garai, P. Lee, and C. M. Uang. 2019. “Cyclic behavior of electroslag welded joints in beam-to-built-up box column steel moment connections.” J. Struct. Eng. 145 (12): 04019146. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002409.
Padilla-Llano, D. A., and J. Ocel. 2021. “Qualification of electroslag welds made from HPS 485W (70W) and 345W (50W) steels.” J. Constr. Steel Res. 183 (Aug): 106705. https://doi.org/10.1016/j.jcsr.2021.106705.
Rice, J. R. 1968. “A path independent integral and the approximate analysis of strain concentration for notches and cracks.” J. Appl. Mech. 35 (Mar): 379–386. https://doi.org/10.1115/1.3601206.
Skiadopoulos, A., and D. Lignos. 2022. “Proposed backing bar detail in welded beam-to-column connections for seismic applications.” J. Struct. Eng. 148 (8): 04022102. https://doi.org/10.1061/(ASCE)ST.1943-541X.0003374.
Smith, C. M., A. M. Kanvinde, and G. G. Deierlein. 2017. “Calibration of continuum cyclic constitutive models for structural steel using particle swarm optimization.” J. Eng. Mech. 143 (5): 04017012. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001214.
Smith, C. M., A. Ziccarelli, M. Terashima, A. M. Kanvinde, and G. Deierlein. 2021. “A stress-weighted ductile fracture model for steel subjected to ultra low cycle fatigue.” Eng. Struct. 245 (Oct): 112964. https://doi.org/10.1016/j.engstruct.2021.112964.
Stillmaker, K., A. M. Kanvinde, and C. Galasso. 2015. “Fracture mechanics-based design of column splices with partial joint penetration welds.” J. Struct. Eng. 42 (2): 04015115. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001380.
Tsai, C. Y., K. C. Tsai, C. H. Li, C. C. Wu, K. C. Lin, and S. J. Jhuang. 2020. “Seismic fracture evaluation of diaphragm joints in welded beam-to-box column moment connections.” Earthquake Eng. Struct. Dyn. 49 (Jan): 1344–1362. https://doi.org/10.1002/eqe.3293.
Yasumoto, H. 2023. “Fracture toughness demands in seismic moment frame connections of box columns.” Master’s thesis, Dept. of Civil and Environmental Engineering, Univ. of California.
Zhu, Y., B. Fell, and A. M. Kanvinde. 2021. “Continuum damage mechanics based ductile fatigue-fracture prediction in buckling steel braces.” J. Constr. Steel Res. 184 (Sep): 106812.https://doi.org/10.1016/j.jcsr.2021.106812.
Ziccarelli, A., A. Kanvinde, and G. Deierlein. 2023. “Cyclic adaptive cohesive zone model to simulate ductile crack propagation in steel structures due to ultra-low cycle fatigue.” Fatigue Fract. Eng. Mater. Struct. 46 (5): 1821–1836. https://doi.org/10.1111/ffe.13964.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 150 • Issue 5 • May 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Jul 27, 2023
Accepted: Nov 28, 2023
Published online: Feb 21, 2024
Published in print: May 1, 2024
Discussion open until: Jul 21, 2024
ASCE Technical Topics:
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.