Effects of Liquefied Waste Plastics on Chemical and Rheological Properties of Bitumen
Publication: Journal of Transportation Engineering, Part B: Pavements
Volume 149, Issue 2
Abstract
This paper studies the merits of applying liquified polyethylene (PE) as a modifier for bitumen. Chemical recycling of PE is often incomplete and generates some amount of waste “PE oil”. The viscoelasticity and chemical characteristics of bitumen modified with PE oil were examined using dynamic shear rheometry, infrared spectroscopy, and adhesion measurements in comparison and in conjunction with bitumen modified with wax, which is one of the most common additives in warm-mix bitumen. The study found that PE oil softens bitumen without severely increasing the creep compliance or viscoelastic damping properties. Wax-modified bitumen showed enrichment of crystallized alkanes at the free bitumen surface that negatively impacted adhesion and interface healing. The introduction of PE oil to wax-modified bitumen did not appreciably decrease the fraction of crystallized wax. Thus, PE oil may not be effective as an additive for warm-mix wax-modified bitumen. However, the PE oil showed potential in protecting bitumen against ultraviolet (UV) aging, and it is worth further exploration as an anti-aging agent, or as a rejuvenator for reclaimed asphalt pavement. The outcomes of this study promote plastic recycling by presenting the merits of applications of liquefied waste PE in the design and engineering of bituminous composites.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This work was sponsored by the National Science Foundation (Award No. 1935723). The authors thank Dr. Kodanda Phani Raj Dandamudi (Arizona State University) for his generous help with HTL processing, extraction, and GC-MS of the PE oil.
References
ASTM. 2020. Standard test method for multiple stress creep and recovery (MSCR) of asphalt binder using a dynamic shear rheometer. ASTM D7405. West Conshohocken, PA: ASTM International.
Behnood, A. 2019. “Application of rejuvenators to improve the rheological and mechanical properties of asphalt binders and mixtures: A review.” J. Cleaner Prod. 231 (Sep): 171–182. https://doi.org/10.1016/j.jclepro.2019.05.209.
Blom, J., H. Soenen, N. Van den Brande, and W. Van den Bergh. 2021. “New evidence on the origin of ‘bee structures’ on bitumen and oils, by atomic force microscopy (AFM) and confocal laser scanning microscopy (CLSM).” Fuel 303 (Nov): 121265. https://doi.org/10.1016/j.fuel.2021.121265.
Celik, G., et al. 2019. “Upcycling single-use polyethylene into high-quality liquid products.” ACS Cent. Sci. 5 (11): 1795–1803. https://doi.org/10.1021/acscentsci.9b00722.
Cheraghian, G., A. Cannone Falchetto, Z. You, S. Chen, Y. S. Kim, J. Westerhoff, K. H. Moon, and M. P. Wistuba. 2020. “Warm mix asphalt technology: An up to date review.” J. Cleaner Prod. 268 (Sep): 122128. https://doi.org/10.1016/j.jclepro.2020.122128.
Coates, G. W., and Y. D. Y. L. Getzler. 2020. “Chemical recycling to monomer for an ideal, circular polymer economy.” Nat. Rev. Mater. 5 (7): 501–516. https://doi.org/10.1038/s41578-020-0190-4.
Fang, Y., Z. Zhang, J. Yang, and X. Li. 2021. “Comprehensive review on the application of bio-rejuvenator in the regeneration of waste asphalt materials.” Constr. Build. Mater. 295 (Aug): 123631. https://doi.org/10.1016/j.conbuildmat.2021.123631.
Ge, D., S. Chen, Z. You, X. Yang, H. Yao, M. Ye, and Y. K. Yap. 2019. “Correlation of DSR results and FTIR’s carbonyl and sulfoxide indexes: Effect of aging temperature on asphalt rheology.” J. Mater. Civ. Eng. 31 (7): 04019115. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002781.
Geyer, R., J. R. Jambeck, and K. L. Law. 2017. “Production, use, and fate of all plastics ever made.” Sci. Adv. 3 (7): e1700782. https://doi.org/10.1126/sciadv.1700782.
Hung, A. M., and E. H. Fini. 2015. “AFM study of asphalt binder ‘bee’ structures: Origin, mechanical fracture, topological evolution, and experimental artifacts.” RSC Adv. 5 (117): 96972–96982. https://doi.org/10.1039/C5RA13982A.
Hung, A. M., M. Kazembeyki, C. G. Hoover, and E. H. Fini. 2019. “Evolution of morphological and nanomechanical properties of bitumen thin films as a result of compositional changes due to ultraviolet radiation.” ACS Sustainable Chem. Eng. 7 (21): 18005–18014. https://doi.org/10.1021/acssuschemeng.9b04846.
Hung, A. M., M. Mousavi, and E. H. Fini. 2020. “Implication of wax on hindering self-healing processes in bitumen.” Appl. Surf. Sci. 523 (Sep): 146449. https://doi.org/10.1016/j.apsusc.2020.146449.
Ignatyev, I. A., W. Thielemans, and B. Vander Beke. 2014. “Recycling of polymers: A review.” ChemSusChem 7 (6): 1579–1593. https://doi.org/10.1002/cssc.201300898.
Jambeck, J. R., R. Geyer, C. Wilcox, T. R. Siegler, M. Perryman, A. Andrady, R. Narayan, and K. L. Law. 2015. “Plastic waste inputs from land into the ocean.” Science 347 (6223): 768–771. https://doi.org/10.1126/science.1260352.
Larkin, P. J. 2018. Infrared and Raman spectroscopy: Principles and spectral interpretation. Cambridge, MA: Elsevier.
Li, C., S. Wu, Z. Chen, G. Tao, and Y. Xiao. 2018. “Enhanced heat release and self-healing properties of steel slag filler based asphalt materials under microwave irradiation.” Constr. Build. Mater. 193 (Dec): 32–41. https://doi.org/10.1016/j.conbuildmat.2018.10.193.
Lu, X., P. Sjövall, and H. Soenen. 2017. “Structural and chemical analysis of bitumen using time-of-flight secondary ion mass spectrometry (TOF-SIMS).” Fuel 199 (Jul): 206–218. https://doi.org/10.1016/j.fuel.2017.02.090.
Mannan, U. A., M. Ahmad, and R. A. Tarefder. 2017. “Influence of moisture conditioning on healing of asphalt binders.” Constr. Build. Mater. 146 (Aug): 360–369. https://doi.org/10.1016/j.conbuildmat.2017.04.087.
Merk, S., A. Blume, and M. Riederer. 1997. “Phase behaviour and crystallinity of plant cuticular waxes studied by Fourier transform infrared spectroscopy.” Planta 204 (1): 44–53. https://doi.org/10.1007/s004250050228.
Miandad, R., M. A. Barakat, A. S. Aburiazaiza, M. Rehan, and A. S. Nizami. 2016. “Catalytic pyrolysis of plastic waste: A review.” Process Saf. Environ. Prot. 102 (Jul): 822–838. https://doi.org/10.1016/j.psep.2016.06.022.
Okan, M., H. M. Aydin, and M. Barsbay. 2019. “Current approaches to waste polymer utilization and minimization: A review.” J. Chem. Technol. Biotechnol. 94 (1): 8–21. https://doi.org/10.1002/jctb.5778.
Pahlavan, F., M. Mousavi, A. Hung, and E. H. Fini. 2016. “Investigating molecular interactions and surface morphology of wax-doped asphaltenes.” Phys. Chem. Chem. Phys. 18 (13): 8840–8854. https://doi.org/10.1039/C5CP07180A.
Passamonti, F. J., and U. Sedran. 2012. “Recycling of waste plastics into fuels. LDPE conversion in FCC.” Appl. Catal., B 125 (Aug): 499–506. https://doi.org/10.1016/j.apcatb.2012.06.020.
Qureshi, M. S., A. Oasmaa, H. Pihkola, I. Deviatkin, A. Tenhunen, J. Mannila, H. Minkkinen, M. Pohjakallio, and J. Laine-Ylijoki. 2020. “Pyrolysis of plastic waste: Opportunities and challenges.” J. Anal. Appl. Pyrolysis 152 (Nov): 104804. https://doi.org/10.1016/j.jaap.2020.104804.
Ritchie, H., and M. Roser. 2018. “Plastic pollution.” Our World in Data. Accessed June 15, 2021. https://ourworldindata.org/plastic-pollution.
Roy, P. S., G. Garnier, F. Allais, and K. Saito. 2021. “Strategic approach towards plastic waste valorization: Challenges and promising chemical upcycling possibilities.” ChemSusChem 14 (19): 4007–4027. https://doi.org/10.1002/cssc.202100904.
Schmets, A., N. Kringos, T. Pauli, P. Redelius, and T. Scarpas. 2010. “On the existence of wax-induced phase separation in bitumen.” Int. J. Pavement Eng. 11 (6): 555–563. https://doi.org/10.1080/10298436.2010.488730.
Sun, D., T. Lin, X. Zhu, Y. Tian, and F. Liu. 2016. “Indices for self-healing performance assessments based on molecular dynamics simulation of asphalt binders.” Comput. Mater. Sci. 114 (Mar): 86–93. https://doi.org/10.1016/j.commatsci.2015.12.017.
Tennakoon, A., et al. 2020. “Catalytic upcycling of high-density polyethylene via a processive mechanism.” Nat. Catal. 3 (11): 893–901. https://doi.org/10.1038/s41929-020-00519-4.
Zhang, F., M. Zeng, R. D. Yappert, J. Sun, Y.-H. Lee, A. M. LaPointe, B. Peters, M. M. Abu-Omar, and S. L. Scott. 2020. “Polyethylene upcycling to long-chain alkylaromatics by tandem hydrogenolysis/aromatization.” Science 370 (6515): 437–441. https://doi.org/10.1126/science.abc5441.
Zhu, J., R. Balieu, and H. Wang. 2021. “The use of solubility parameters and free energy theory for phase behaviour of polymer-modified bitumen: A review.” Road Mater. Pavement Des. 22 (4): 757–778. https://doi.org/10.1080/14680629.2019.1645725.
Zhu, J., B. Birgisson, and N. Kringos. 2014. “Polymer modification of bitumen: Advances and challenges.” Eur. Polym. J. 54 (May): 18–38. https://doi.org/10.1016/j.eurpolymj.2014.02.005.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jan 19, 2022
Accepted: Dec 26, 2022
Published online: Feb 13, 2023
Published in print: Jun 1, 2023
Discussion open until: Jul 13, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.