Numerical Investigation of the Bond-Slip Behavior between Double-Helix BFRP Macrofibers and Concrete
Publication: Journal of Materials in Civil Engineering
Volume 36, Issue 12
Abstract
Basalt fiber–reinforced polymer (BFRP) is widely used to reinforce concrete due to its high strength, lightweight nature, good corrosion resistance, and low cost. Previous studies have shown that the double-helix BFRP macrofiber has better bond behavior with concrete compared with other types of BFRP fibers. This is attributed to its irregular geometry. The bond-slip behavior between double-helix BFRP macrofiber and concrete is further numerically studied in this study. The corresponding finite-element model is established, and the accuracy of the numerical method is validated by the experimental results based on fiber-matrix pullout tests. The effects of twisted pitches, bundle numbers, and cross-section shapes of the fiber on the bond-slip behavior are extensively investigated and discussed. It is shown by the numerical results that the bond stress and energy-dissipating capacity increase with the decrease of twisted pitches (30, 20, 10, and 5 mm). The bond stress of the fiber with a twisted pitch of 5 mm can be increased by 17.0% at most compared with the fiber with a twisted pitch of 30 mm. Furthermore, it is found that the double-helix BFRP fiber has higher bond stress than the fiber with three or four bundles, with corresponding increases of 11.9% and 16.9%, respectively.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or codes that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors would like to acknowledge financial support from the National Natural Science Foundation of China (Grant No. 52208498), the China Postdoctoral Science Foundation (Grant No. 2023M732608), the Tianjin Nature Science Foundation (Grant No. 23JCQNJC00900), the Postdoctoral Fellowship Program of CPSF under Grant No. GZC20231359, and the “Spring Sunshine Plan” cooperative research project of the Ministry of Education of China (Grant No. HZKY20220593).
References
Abdallah, S., M. Z. Fan, and D. W. Rees. 2017. “Effect of elevated temperature on pull-out behavior of 4DH/5DH hooked end steel fibres.” Compos. Struct. 165 (Apr): 180–191. https://doi.org/10.1016/j.compstruct.2017.01.005.
Abrishambaf, A., J. A. O. Barros, V. M. C. F. Cunha, and C. Frazão. 2017. “Time dependent behaviour of fibre pull-out in self-compacting concrete.” Cem. Concr. Compos. 77 (Mar): 14–28. https://doi.org/10.1016/j.cemconcomp.2016.12.004.
Attiaa, K., W. Alnahhal, A. Elrefaia, and Y. Rihanb. 2019. “Flexural behavior of basalt fiber-reinforced concrete slab strips reinforced with BFRP and GFRP bars.” Compos. Struct. 211 (Mar): 1–12. https://doi.org/10.1016/j.compstruct.2018.12.016.
Chan, Y-W., and S-H. Chu. 2004. “Effect of silica fume on steel fiber bond characteristics in reactive powder concrete.” Cem. Concr. Res. 34 (7): 1167–1172. https://doi.org/10.1016/j.cemconres.2003.12.023.
Chen, W. S., T. M. Pham, H. Sichembe, L. Chen, and H. Hao. 2018. “Experimental study of flexural behavior of RC beams strengthened by longitudinal and U-shaped basalt FRP sheet.” Composites, Part B 134 (Feb): 114–126. https://doi.org/10.1016/j.compositesb.2017.09.053.
Chinese Standard. 2010. Code for design of concrete structures. GB 50010-2010. Beijing: Chinese Standard Press.
Cuenca, E., J. Echegaray-Oviedo, and P. Serna. 2015. “Influence of concrete matrix and type of fiber on the shear behavior of self-compacting fiber reinforced concrete beams.” Composites, Part B 75 (Jun): 135–147. https://doi.org/10.1016/j.compositesb.2015.01.037.
Cunha, V. M. C. F., J. A. O. Barros, and J. M. Sena-Cruz. 2010. “Pullout behavior of steel fibers in self-compacting concrete.” J. Mater. Civ. Eng. 22 (1): 1–9. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000001.
Deng, F. Q., X. X. Ding, Y. Chi, L. H. Xu, and L. Wang. 2018. “The pull-out behavior of straight and hooked-end steel fiber from hybrid fiber reinforced cementitious composite: Experimental study and analytical modelling.” Compos. Struct. 206 (Dec): 693–712. https://doi.org/10.1016/j.compstruct.2018.08.066.
Elgabbas, F., E. A. Ahmed, and B. Benmokrane. 2015. “Physical and mechanical characteristics of new basalt FRP bars for reinforcing concrete structures.” Constr. Build. Mater. 95 (Oct): 623–635. https://doi.org/10.1016/j.conbuildmat.2015.07.036.
Hajsadeghi, M., S. C. Chee, and S. W. Jones. 2018. “Development of a generic three-dimensional finite element fibre pullout model.” Constr. Build. Mater. 185 (Oct): 354–368. https://doi.org/10.1016/j.conbuildmat.2018.07.069.
Hao, Y. F., and H. Hao. 2017. “Pull-out behavior of spiral-shaped steel fibers from normal-strength concrete matrix.” Constr. Build. Mater. 139 (May): 34–44. https://doi.org/10.1016/j.conbuildmat.2017.02.040.
Huang, H. H., X. J. Gao, and K. H. Khayat. 2021. “Contribution of fiber alignment on flexural properties of UHPC and prediction using the composite theory.” Cem. Concr. Compos. 118 (Apr): 103971. https://doi.org/10.1016/j.cemconcomp.2021.103971.
Isla, F., G. Ruano, and B. Luccioni. 2015. “Analysis of steel fibers pull-out. Experimental study.” Constr. Build. Mater. 100 (Dec): 183–193. https://doi.org/10.1016/j.conbuildmat.2015.09.034.
Jin, L., M. J. Liu, R. B. Zhang, and X. L. Du. 2020. “3D meso-scale modelling of the interface behavior between ribbed steel bar and concrete.” Eng. Fract. Mech. 239 (Nov): 107291. https://doi.org/10.1016/j.engfracmech.2020.107291.
John, V. J., and B. Dharmar. 2021. “Influence of basalt fibers on the mechanical behavior of concrete—A review.” Struct. Concr. 22 (1): 491–502. https://doi.org/10.1002/suco.201900086.
Lee, J., and G. L. Fenves. 1998. “Plastic-damage model for cyclic loading of concrete structures.” J. Eng. Mech. 124 (8): 892–900. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:8(892).
Li, B., L. H. Xu, Y. H. Shi, Y. Chi, Q. Liu, and C. N. Li. 2018. “Effects of fiber type, volume fraction and aspect ratio on the flexural and acoustic emission behaviors of steel fiber reinforced concrete.” Constr. Build. Mater. 181 (Aug): 474–486. https://doi.org/10.1016/j.conbuildmat.2018.06.065.
Li, X., Z. Gao, Y. W. Zhou, L. L. Sui, and C. Chen. 2021. “Optimizing natural fiber reinforced polymer strengthening of RC beams.” Mater. Struct. 54 (Apr): 66–84. https://doi.org/10.1617/s11527-021-01663-4.
Lubliner, J., J. Ollivier, S. Oller, and E. Onate. 1989. “A plastic-damage model for concrete.” Int. J. Solid Struct. 25 (3): 299–326. https://doi.org/10.1016/0020-7683(89)90050-4.
Naaman, A. E., and H. Najm. 1991. “Bond-slip mechanisms of steel fibers in concrete.” ACI Mater. J. 88 (2): 135–145. https://doi.org/10.14359/1896.
Naaman, A. E., G. G. Namur, J. M. Alwan, and H. S. Najm. 1991. “Fiber pullout and bond slip. I: Analytical study.” J. Struct. Eng. 117 (9): 2769–2790. https://doi.org/10.1061/(ASCE)0733-9445(1991)117:9(2769).
Nassani, D. E. 2020. “Experimental and analytical study of the mechanical and flexural behavior of hybrid fiber concretes.” Structures 28 (Dec): 1746–1755. https://doi.org/10.1016/j.istruc.2020.10.014.
Pham, T. M., W. S. Chen, M. Elchalakani, A. Karrech, and H. Hao. 2020. “Experimental investigation on lightweight rubberized concrete beams strengthened with BFRP sheets subjected to impact loads.” Eng. Struct. 205 (Feb): 110095. https://doi.org/10.1016/j.engstruct.2019.110095.
Shi, Y. C. 2009. “Dynamic response and damage mechanism of reinforced concrete structures under blast loading.” Doctoral thesis, School of Civil Engineering, Tianjin Univ.
Tai, Y.-S., and S. El-Tawil. 2017. “High loading-rate pullout behavior of inclined deformed steel fibers embedded in ultra-high performance concrete.” Constr. Build. Mater. 148 (Sep): 204–218. https://doi.org/10.1016/j.conbuildmat.2017.05.018.
Tran, T. T., T. M. Pham, Z. J. Huang, W. S. Chen, H. Hao, and M. Elchalakani. 2021. “Impact response of fibre reinforced geopolymer concrete beams with BFRP bars and stirrups.” Eng. Struct. 231 (Mar): 111758. https://doi.org/10.1016/j.engstruct.2020.111785.
Tuyan, M., and H. Yazici. 2012. “Pull-out behavior of single steel fiber from SIFCON matrix.” Constr. Build. Mater. 35 (Oct): 571–577. https://doi.org/10.1016/j.conbuildmat.2012.04.110.
Xu, W. D., L. Yang, D. Y. Gao, J. Y. Tang, G. W. Sun, and Y. S. Zhang. 2023. “Mechanical properties of seawater-mixed steel fiber reinforced concrete.” J. Build. Eng. 73 (Aug): 106823. https://doi.org/10.1016/j.jobe.2023.106823.
Yoo, D.-Y., J.-J. Park, and S.-W. Kim. 2017. “Fiber pullout behavior of HPFRCC: Effects of matrix strength and fiber type.” Compos. Struct. 174 (Aug): 263–276. https://doi.org/10.1016/j.compstruct.2017.04.064.
Zhang, C. L., H. Hao, and Y. F. Hao. 2021. “Development of double-helix macro BFRP fibers for concrete reinforcement.” Mater. Struct. 54 (4): 165. https://doi.org/10.1617/s11527-021-01762-2.
Zhang, C. L., H. Hao, and Y. F. Hao. 2022a. “Experimental study of mechanical properties of double-helix BFRP fiber reinforced concrete at high strain rates.” Cem. Concr. Compos. 132 (Sep): 104633. https://doi.org/10.1016/j.cemconcomp.2022.104633.
Zhang, C. L., H. Hao, and Y. F. Hao. 2023. “Experimental investigation of responses of macro double-helix BFRP fibers reinforced RC beams subjected to static and impact loads.” Eng. Struct. 276 (Feb): 115346. https://doi.org/10.1016/j.engstruct.2022.115346.
Zhang, R. B., L. Jin, M. J. Liu, X. L. Du, and J. B. Liu. 2022b. “Refined modeling of the interfacial behavior between FRP bars and concrete under different loading rates.” Compos. Struct. 291 (Jul): 115676. https://doi.org/10.1016/j.compstruct.2022.115676.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Jan 2, 2024
Accepted: Apr 26, 2024
Published online: Oct 3, 2024
Published in print: Dec 1, 2024
Discussion open until: Mar 3, 2025
ASCE Technical Topics:
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.