Effect of Pyrophyllite Grain Size on the Mechanical Durability and Radiation-Shielding Properties of Concrete
Publication: Journal of Materials in Civil Engineering
Volume 36, Issue 11
Abstract
Concrete is the favored construction material, with more than 7 billion cubic meters manufactured annually. Aggregates constitute the crucial component of its structure and quality, responsible for its exceptional characteristic features. The characteristics of aggregates determine the mechanical durability and radiation performance of concrete. In this investigation, fabricated concrete specimens were generated by replacing sand and aggregate sizes with pyrophyllite in 10%–20%–30%–100% proportions. The study investigated the mechanical properties of concrete specimens using both pressure and ultrasound methods, as well as their durability under freeze–thaw and high-temperature (200°C–1,000°C) conditions. In addition, the microstructure and radiation permeability properties were examined over a 7–28–90-day period. Notably, the use of pyrophyllite sand and aggregate significantly increased the compressive strength of the specimens by 21%–63% when compared to the reference concrete after 7–28–90 days, while also reducing mass loss by up to 4.6% during freeze–thaw cycles. After subjecting the specimens to high temperatures, it was discovered that those with an air-cooling regime achieved a compressive value 45% higher than the reference concrete. Microstructure images revealed the formation of C─ S─ H, CH, and portlandite hydration products over 90 days, supporting the observed compressive strength values. The study also has an effective linear attenuation coefficient (LAC) for radiation-shielding properties. According to some radiation-shielding parameters calculated through LAC values, it was revealed that these concrete samples were suitable shielding materials. Pyrophyllite-reinforced specimens have demonstrated potential for high-strength concrete production, suitability for use in high-temperature environments, and effectiveness as shielding in areas with radiation sources.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This study was supported by the Scientific Research Projects Coordination Unit of Kahramanmaraş Sütçü İmam University. Project numbers 2023/6-22 A, 2024/2-14 D, and 2024/2-15 D.
References
Aarthi, K., and K. Arunachalam. 2018. “Durability studies on fibre reinforced self compacting concrete with sustainable wastes.” J. Cleaner Prod. 174 (Mar): 247–255. https://doi.org/10.1016/j.jclepro.2017.10.270.
Akkurt, I., H. Akyýldýrým, B. Mavi, S. Kilincarslan, and C. Basyigit. 2010. “Photon attenuation coefficients of concrete includes barite in different rate.” Ann. Nucl. Energy 37 (7): 910–914. https://doi.org/10.1016/j.anucene.2010.04.001.
Akkurt, I., C. Basyigit, S. Kilincarslan, and B. Mavi. 2005. “The shielding of -rays by concretes produced with barite.” Prog. Nucl. Energy 46 (1): 1–11. https://doi.org/10.1016/j.pnucene.2004.09.015.
Ali, M. A., H. A. M. Ahmed, H. M. Ahmed, and M. Hefni. 2021. “Pyrophyllite: An economic mineral for different industrial applications.” Appl. Sci. 11 (23): 11357. https://doi.org/10.3390/app112311357.
ASTM. n.d. Freeze-thaw testing of concrete. ASTM C666/C666M. West Conshohocken, PA: ASTM.
Aydin, S., and B. Baradan. 2007. “Effect of pumice and fly ash incorporation on high temperature resistance of cement based mortars.” Cem. Concr. Res. 37 (6): 988–995. https://doi.org/10.1016/j.cemconres.2007.02.005.
Benaicha, M., O. Jalbaud, A. Hafidi Alaoui, and Y. Burtschell. 2015. “Correlation between the mechanical behavior and the ultrasonic velocity of fiber-reinforced concrete.” Constr. Build. Mater. 101 (Mar): 702–709. https://doi.org/10.1016/j.conbuildmat.2015.10.047.
Bilici, S., N. Kabay, N. Miyan, T. Omur, and H. Ozkan. 2023. “Effect of washing aggregate sludge waste on the properties of alkali-activated blast furnace slag.” J. Build. Eng. 63 (PA): 105527. https://doi.org/10.1016/j.jobe.2022.105527.
Binici, H., and O. Aksogan. 2018. “Durability of concrete made with natural granular granite, silica sand and powders of waste marble and basalt as fine aggregate.” J. Build. Eng. 19: 109–121. https://doi.org/10.1016/j.jobe.2018.04.022.
Binici, H., O. Aksogan, E. B. Görür, H. Kaplan, and M. N. Bodur. 2008. “Performance of ground blast furnace slag and ground basaltic pumice concrete against seawater attack.” Constr. Build. Mater. 22 (7): 1515–1526. https://doi.org/10.1016/j.conbuildmat.2007.03.024.
BIS (Bureau of Indian Standards). 1992. Method of non-destructive testing of concret, part 1: Ultrasonic pulse velocity. IS 13311. New Delhi, India: BIS.
Chan, Y. N., G. F. Peng, and M. Anson. 1999. “Residual strength and pore structure of high-strength concrete and normal strength concrete after exposure to high temperatures.” Cem. Concr. Compos. 21 (1): 23–27. https://doi.org/10.1016/S0958-9465(98)00034-1.
Chilton, A. B., J. K. Shultis, and R. E. Faw. 1984. Principles of radiation shielding. Hoboken, NJ: Prentice Hall.
Coşkunsu, A. 2022. “Investigation of physical and mechanical properties of heavy concrete with self compacting barite aggregate produced by using different additives.” Master’s thesis, Dept. of Civil Engineering, Süleyman Demirel Univ., Institute of Natural and Applied Sciences.
Çullu, M., and E. Bakırhan. 2018. “Investigation of radiation absorption coefficients of lead-zinc mine waste rock mixed heavy concrete at 662–1460 keV energy range.” Constr. Build. Mater. 173 (Mar): 17–27. https://doi.org/10.1016/j.conbuildmat.2018.03.175.
Çullu, M., and H. Ertaş. 2016. “Determination of the effect of lead mine waste aggregate on some concrete properties and radiation shielding.” Constr. Build. Mater. 125 (Mar): 625–631. https://doi.org/10.1016/j.conbuildmat.2016.08.069.
Demez, A. 2017. “Research of fire resistance of the high strength concrete produced with pyrophyllite aggregate.” Master’s thesis, Dept. of Civil Engineering, Inönü Univ.
Demir, F., G. Budak, R. Sahin, A. Karabulut, M. Oltulu, and A. Un. 2011. “Determination of radiation attenuation coefficients of heavyweight- and normal-weight concretes containing colemanite and barite for 0.663 MeV .” Ann. Nucl. Energy 38 (6): 1274–1278. https://doi.org/10.1016/j.anucene.2011.02.009.
Dong, F., H. Wang, J. Yu, K. Liu, Z. Guo, X. Duan, and X. Qiong. 2021. “Effect of freeze–thaw cycling on mechanical properties of polyethylene fiber and steel fiber reinforced concrete.” Constr. Build. Mater. 295 (Aug): 123427. https://doi.org/10.1016/j.conbuildmat.2021.123427.
Dündar, B., E. Çınar, and H. Özkaya. 2019. “Investigation of physical and mechanical properties of profillite added fiber mortars.” J. Adv. Technol. Sci. 8 (2): 17–27.
Eken, M. 2023. “Mechanical and durability properties of concrete with volcanic rock additives.” J. Mater. Civ. Eng. 35 (7): 1–12. https://doi.org/10.1061/JMCEE7.MTENG-14995.
Eken, M., and E. Avşaroğlu. 2021. “Yüksek Fırın Cürufu, Bazalt ve Üleksit Katkılı Beton Örneklerin Yüksek Sıcaklık Etkisi Altında Özelliklerinin İncelenmesi.” Düzce Üniversitesi Bilim ve Teknoloji Dergisi 9 (3): 306–320. https://doi.org/10.29130/dubited.824747.
Eskalen, H., Y. Kavun, and M. Kavgacı. 2023. “Preparation and study of radiation shielding features of ZnO nanoparticle reinforced borate glasses.” Appl. Radiat. Isot. 198 (May): 110858. https://doi.org/10.1016/j.apradiso.2023.110858.
Eskalen, H., Y. Kavun, S. Kerli, and S. Eken. 2020. “An investigation of radiation shielding properties of boron doped ZnO thin films.” Opt. Mater. 105 (Mar): 109871. https://doi.org/10.1016/j.optmat.2020.109871.
Fares, A. I., K. Md Abu Sohel, K. Al-Jabri, and A. Al-Saidy. 2023. “Influence of ferrochrome slag as coarse and fine aggregates on thermal and strength properties of concrete at high temperatures.” Constr. Build. Mater. 400 (Aug): 132807. https://doi.org/10.1016/j.conbuildmat.2023.132807.
Gündüz, L., and I. Uǧur. 2005. “The effects of different fine and coarse pumice aggregate/cement ratios on the structural concrete properties without using any admixtures.” Cem. Concr. Res. 35 (9): 1859–1864. https://doi.org/10.1016/j.cemconres.2004.08.003.
Horvath, A. 2004. “Construction materials and the environment.” Annu. Rev. Environ. Resour. 29 (Mar): 181–204. https://doi.org/10.1146/annurev.energy.29.062403.102215.
Hossain, K. M. A. 2006. “High strength blended cement concrete incorporating volcanic ash: Performance at high temperatures.” Cem. Concr. Compos. 28 (6): 535–545. https://doi.org/10.1016/j.cemconcomp.2006.01.013.
Huang, L., J. C. Liu, R. Cai, and H. Ye. 2021. “Mechanical degradation of ultra-high strength alkali-activated concrete subjected to repeated loading and elevated temperatures.” Cem. Concr. Compos. 121 (Feb): 104083. https://doi.org/10.1016/j.cemconcomp.2021.104083.
Ioannidou, D., G. Meylan, G. Sonnemann, and G. Habert. 2017. “Is gravel becoming scarce? Evaluating the local criticality of construction aggregates.” Resour. Conserv. Recycl. 126 (Dec): 25–33. https://doi.org/10.1016/j.resconrec.2017.07.016.
Itoh, Y., M. J. Bröcker, S. I. Sekine, D. Söll, and S. Yokoyama. 2014. “Dimer-dimer interaction of the bacterial selenocysteine synthase SelA promotes functional active-site formation and catalytic specificity.” J. Mol. Biol. 426 (8): 1723–1735. https://doi.org/10.1016/j.jmb.2014.01.003.
Janotka, I., and T. Nürnbergerová. 2005. “Effect of temperature on structural quality of the cement paste and high-strength concrete with silica fume.” Nucl. Eng. Des. 235 (17–19): 2019–2032. https://doi.org/10.1016/j.nucengdes.2005.05.011.
Kaplan, C. 2020. “Investigation of the effect of sulfuric acid on ground pyrophyllite powder and blast furnace slag added mortars.” Master’s thesis, Dept. of Civil Engineering, Osmaniye Korkut Ata Univ.
Kavun, Y., H. Eskalen, S. Kerli, and M. Kavgaci. 2021. “Fabrication and characterization of GdxFe2O3(100-x) /PVA (x=0, 5, 10, 20) composite films for radiation shielding.” Appl. Radiat. Isot. 177 (Sep): 1–7. https://doi.org/10.1016/j.apradiso.2021.109918.
Kavun, Y., S. Kerli, H. Eskalen, and M. Kavgacı. 2022. “Characterization and nuclear shielding performance of Sm doped thin films.” Radiat. Phys. Chem. 194 (Sep): 110014. https://doi.org/10.1016/j.radphyschem.2022.110014.
Kharita, M. H., S. Yousef, and M. Alnassar. 2011. “Review on the addition of boron compounds to radiation shielding concrete.” Prog. Nucl. Energy 53 (2): 207–211. https://doi.org/10.1016/j.pnucene.2010.09.012.
Khoury, G. A. 1992. “Compressive strength of concrete at high temperatures: A reassessment.” Mag. Concr. Res. 44 (161): 291–309. https://doi.org/10.1680/macr.1992.44.161.291.
Kilinçarslan, Ş., C. Başyiǧit, and I. Akkurt. 2007. “Investigation of heavyweight concrete with barite aggregates for radiation shielding.” J. Fac. Eng. Archit. Gazi Univ. 22 (2): 393–399.
Kukreti, A., P. Kundra, L. Kathait, N. Garg, and S. Kumar. 2022. “A review on properties of heavy weight concrete.” IOP Conf. Ser.: Earth Environ. Sci. 1086 (1): 012049. https://doi.org/10.1088/1755-1315/1086/1/012049.
Li, Q., P. Liu, M. Wang, and H. Xia. 2023. “Effects of elevated temperature on the mechanical properties of concrete with aggregate of waste porcelain tile.” J. Build. Eng. 64 (Jul): 105585. https://doi.org/10.1016/j.jobe.2022.105585.
Liu, M., and Y. Wang. 2012. “Damage constitutive model of fly ash concrete under freeze-thaw cycles.” J. Mater. Civ. Eng. 24 (9): 1165–1174. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000491.
Milasi, S. E., D. Mostofinejad, and H. Bahmani. 2023. “Improving the resistance of ultra-high-performance concrete against nuclear radiation: Replacing cement with barite, hematite, and lead powder.” Dev. Built Environ. 15 (Jun): 100190. https://doi.org/10.1016/j.dibe.2023.100190.
Mohammed, T. U., and A. H. Mahmood. 2016. “Effects of maximum aggregate size on UPV of brick aggregate concrete.” Ultrasonics 69 (Apr): 129–136. https://doi.org/10.1016/j.ultras.2016.04.006.
Mohammed, T. U., and M. N. Rahman. 2016. “Effect of types of aggregate and sand-to-aggregate volume ratio on UPV in concrete.” Constr. Build. Mater. 125 (Oct): 832–841. https://doi.org/10.1016/j.conbuildmat.2016.08.102.
Mostafaei, H., B. Badarloo, N. F. Chamasemani, M. A. Rostampour, and P. Lehner. 2023. “Investigating the effects of concrete mix design on the environmental impacts of reinforced concrete structures.” Buildings 13 (5): 1313. https://doi.org/10.3390/buildings13051313.
Mostafaei, H., F. Behnamfar, and M. Alembagheri. 2022. “Reliability and sensitivity analysis of wedge stability in the abutments of an arch dam using artificial neural network.” Earthquake Eng. Eng. Vibr. 21 (4): 1019–1033. https://doi.org/10.1007/s11803-022-2133-0.
Mutlu, H. 2020. “Utilisation of pyrophyllite in ceramic glazes.” Int. J. Soc. Sci. 9 (2): 555–563. https://orcid.org/0000-0002-8609-9077.
Naik, T. R., V. Mohan Malhotra, and J. S. Popovics. 2004. “The ultrasonic pulse velocity method.” In Handbook on nondestructive testing of concrete, edited by V. M. Malhotra and N. J. Carino, 2nd ed. Boca Raton, FL: CRC Press.
Nemade, P. A., D. Pasla, and A. K. Chandrappa. 2023. “Durability assessment of concrete with natural and Linz Donawitz slag as coarse aggregates.” Constr. Build. Mater. 400 (May): 132617. https://doi.org/10.1016/j.conbuildmat.2023.132617.
Neville, A. M., and J. J. Brooks. 1987. Concrete technology, 438. London: Longman Scientific & Technical.
Peng, X., F. Shi, J. Yang, Q. Yang, H. Wang, and J. Zhang. 2023. “Modification of construction waste derived recycled aggregate via curing to enhance corrosive freeze-thaw durability of concrete.” J. Cleaner Prod. 405 (Nov): 137016. https://doi.org/10.1016/j.jclepro.2023.137016.
Pradhan, A. A. A., M. Das, and S. Goswami. 2015. “Economic potential of pyrophyllite deposits of keonjhar as industrial mineral.” Spec. Publ. Geol. 13 (13): 86–90.
Qiu, J., Y. Zhou, N. I. Vatin, X. Guan, S. Sultanov, and K. Khemarak. 2020. “Damage constitutive model of coal gangue concrete under freeze-thaw cycles.” Constr. Build. Mater. 264 (Mar): 120720. https://doi.org/10.1016/j.conbuildmat.2020.120720.
Ren, J., and Y. Lai. 2021. “Study on the durability and failure mechanism of concrete modified with nanoparticles and polypropylene fiber under freeze-thaw cycles and sulfate attack.” Cold Reg. Sci. Technol. 188 (Mar): 103301. https://doi.org/10.1016/j.coldregions.2021.103301.
Şahmaran, M., H. A. Christianto, and I. Ö. Yaman. 2006. “The effect of chemical admixtures and mineral additives on the properties of self-compacting mortars.” Cem. Concr. Compos. 28 (5): 432–440. https://doi.org/10.1016/j.cemconcomp.2005.12.003.
Savva, A., P. Manita, and K. K. Sideris. 2005. “Influence of elevated temperatures on the mechanical properties of blended cement concretes prepared with limestone and siliceous aggregates.” Cem. Concr. Compos. 27 (2): 239–248. https://doi.org/10.1016/j.cemconcomp.2004.02.013.
Shariq, M., J. Prasad, and A. Masood. 2013. “Studies in ultrasonic pulse velocity of concrete containing GGBFS.” Constr. Build. Mater. 40 (Mar): 944–950. https://doi.org/10.1016/j.conbuildmat.2012.11.070.
Singh, M., K. Choudhary, A. Srivastava, K. Singh Sangwan, and D. Bhunia. 2017. “A study on environmental and economic impacts of using waste marble powder in concrete.” J. Build. Eng. 13 (Dec): 87–95. https://doi.org/10.1016/j.jobe.2017.07.009.
Turkish Standardization Institute. 2016. Concrete mix design calculation principles, 112. Ankara, Turkey: Turkish Standardization Institute.
Türk Standardları Enstitüsü. 2010. Beton–Sertleşmiş Beton Deneyleri–Bölüm 3: Deney Numunelerinin Basınç Dayanımının Tayini. TS EN 12390-3. Ankara, Turkey: Türk Standardları Enstitüsü.
Uygun, A., and E. Solakoğlu. 2002. “Geology and origin of pyrophyllite deposits in the Pütürge (Malatya) massif.” MTA J. 123 (124): 13–19. https://doi.org/10.1016/j.jobe.2017.07.009.
Uzbas, B., and A. C. Aydin. 2020. “Microstructural analysis of silica fume concrete with scanning electron microscopy and X-ray diffraction.” Eng. Technol. Appl. Sci. Res. 10 (3): 5845–5850. https://doi.org/10.48084/etasr.3288.
Wang, B., F. Wang, and Q. Wang. 2018. “Damage constitutive models of concrete under the coupling action of freeze–thaw cycles and load based on Lemaitre assumption.” Constr. Build. Mater. 173 (Jun): 332–341. https://doi.org/10.1016/j.conbuildmat.2018.04.054.
Wang, Y., M. Xie, and J. Zhang. 2023. “Mechanical properties and damage model of modified recycled concrete under freeze-thaw cycles.” J. Build. Eng. 78 (Mar): 107680. https://doi.org/10.1016/j.jobe.2023.107680.
Xiao, Q., Z. Wu, J. Qiu, Z. Dong, and S. Shi. 2022. “Capillary water absorption performance and damage constitutive model of recycled concrete under freeze–thaw action.” Constr. Build. Mater. 353 (Aug): 129120. https://doi.org/10.1016/j.conbuildmat.2022.129120.
Xie, Q., L. Zhang, S. Yin, B. Zhang, and Y. Wu. 2019. “Effects of high temperatures on the physical and mechanical properties of carbonated ordinary concrete.” Adv. Mater. Sci. Eng. 1: 5753232. https://doi.org/10.1155/2019/5753232.
Yapıcı, N., H. Güneyli, and E. Mehmetoğlu. 2022. “Comparison of physical and mechanical properties of profillite and zeolite added building materials.” Cukurova Univ. J. Faculty Eng. 37 (2): 419–427.
Yaykaşlı, H., H. Eskalen, Y. Kavun, and M. Gögebakan. 2022. “Microstructural, thermal, and radiation shielding properties of Al50B25Mg25 alloy prepared by mechanical alloying.” J. Mater. Sci.-Mater. Electron. 33 (5): 2350–2359. https://doi.org/10.1007/s10854-021-07434-9.
Yüzer, N., L. Öztürk, B. Akbaş, Ö. Çakır, A. Kızılkanat, and N. Kabay. 2007. Investigation of the relationship between concrete compressive strength and color change in structures exposed to fire. Project No: 103I040. Ankara, Turkey: Turkey Univ.
Zhu, Q., Y. X. Yuan, J. H. Chen, L. Fan, and H. Yang. 2022. “Research on the high-temperature resistance of recycled aggregate concrete with iron tailing sand.” Constr. Build. Mater. 327 (Jan): 126889. https://doi.org/10.1016/j.conbuildmat.2022.126889.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 36 • Issue 11 • November 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Nov 8, 2023
Accepted: Apr 9, 2024
Published online: Sep 3, 2024
Published in print: Nov 1, 2024
Discussion open until: Feb 3, 2025
ASCE Technical Topics:
- Aggregates
- Chemical processes
- Chemistry
- Compressive strength
- Concrete
- Engineering materials (by type)
- Engineering mechanics
- Environmental engineering
- Infrastructure
- Material durability
- Material mechanics
- Material properties
- Materials engineering
- Mechanical properties
- Pavements
- Radiation
- Strength of materials
- Transportation engineering
- Waste management
- Waste treatment
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.