Influence of Water Saturation on Dynamic Tensile and Compressive Behaviors of Concrete
Publication: Journal of Materials in Civil Engineering
Volume 36, Issue 6
Abstract
This paper experimentally investigates the influence of saturation on dynamic behaviors of concrete under both tension and compression stress states. Two grades of concrete were saturated to 0%, 50%, and 100% by oven drying and water soaking procedures. Split Hopkinson pressure bar (SHPB) tests, reaching the highest strain rate of about , were carried out for dynamic compression. Dynamic splitting tensile tests were carried out by an Instron high-speed test machine, achieving the highest strain rate of about . The test results show that concrete specimens with different saturation ratios are all strain rate-sensitive. Under tensile loading, the effect of free on viscosity is only found to affect concrete’s behavior when the strain rate is not very high. The strain rate sensitivity increases with water content when the strain rate is lower than about . However, when the strain rate is greater than , strain rate sensitivity of concretes with different saturations become similar. Under compressive loading, free water in pores reduces the rate effect because it increases the hydrostatic pressure inside the specimen and leads to hydraulic fracturing. The microcracks caused by the hydraulic fracturing effect in the specimen result in macroscopic strength degeneration.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors gratefully acknowledge the support from National Nature Science Foundation of China under Grant Nos. 51938011 and 51908405.
References
Burlion, N., F. Bourgeois, and J. F. Shao. 2005. “Effects of desiccation on mechanical behaviour of concrete.” Cem. Concr. Compos. 27 (3): 367–379. https://doi.org/10.1016/j.cemconcomp.2004.05.004.
Chen, X., W. Huang, and J. Zhou. 2012. “Effect of moisture content on compressive and split tensile strength of concrete.” Indian J. Eng. Mater. Sci. 19 (6): 427–435.
Chen, X., Y. Shao, L. Xu, and C. Chen. 2015. “Experimental study on tensile behavior of cement paste, mortar and concrete under high strain rates.” J. Wuhan Univ. Technol. 30 (6): 1268–1273. https://doi.org/10.1007/s11595-015-1306-3.
Cui, J., H. Hao, and Y. Shi. 2017. “Discussion on the suitability of concrete constitutive models for high-rate response predictions of RC structures.” Int. J. Impact Eng. 106 (Aug): 202–216. https://doi.org/10.1016/j.ijimpeng.2017.04.003.
Cui, J., H. Hao, and Y. Shi. 2018. “Numerical study of the influences of pressure confinement on high-speed impact tests of dynamic material properties of concrete.” Constr. Build. Mater. 171 (May): 839–849. https://doi.org/10.1016/j.conbuildmat.2018.03.170.
Erzar, B., and P. Forquin. 2011. “Free water influence on the dynamic tensile behaviour of concrete.” Appl. Mech. Mater. 82 (Sep): 45–50. https://doi.org/10.4028/www.scientific.net/AMM.82.45.
Forquin, P., K. Safa, and G. Gary. 2010. “Influence of free water on the quasi-static and dynamic strength of concrete in confined compression tests.” Cem. Concr. Res. 40 (2): 321–333. https://doi.org/10.1016/j.cemconres.2009.09.024.
Fu, Q., Y. Xie, G. Long, D. Niu, H. Song, and X. Liu. 2017. “Impact characterization and modelling of cement and asphalt mortar based on SHPB experiments.” Int. J. Impact Eng. 106 (Aug): 44–52. https://doi.org/10.1016/j.ijimpeng.2017.03.009.
Ha, N. S., S. S. Marundrury, T. M. Pham, E. Pournasiri, F. Shi, and H. Hao. 2022. “Effect of grounded blast furnace slag and rice husk ash on performance of ultra-high-performance concrete (UHPC) subjected to impact loading.” Constr. Build. Mater. 329 (Apr): 127213. https://doi.org/10.1016/j.conbuildmat.2022.127213.
Hao, Y., H. Hao, and Z. X. Li. 2013. “Influence of end friction confinement on impact tests of concrete material at high strain rate.” Int. J. Impact Eng. 60 (60): 82–106. https://doi.org/10.1016/j.ijimpeng.2013.04.008.
Holtz, R. D., and W. D. Kovacs. 1981. An introduction to geotechnical engineering. Englewood Cliffs, NJ: Prentice-Hall.
Hover, K. C. 2011. “The influence of water on the performance of concrete.” Constr. Build. Mater. 25 (7): 3003–3013. https://doi.org/10.1016/j.conbuildmat.2011.01.010.
Huang, R., L. Hu, J. Qin, D. Jiang, and L. Meng. 2021. “Effect of free water on the mechanical properties and blast resistance of concrete.” KSCE J. Civ. Eng. 25 (8): 3084–3096. https://doi.org/10.1007/s12205-021-2169-0.
Huang, X., X. Kong, J. Hu, X. Zhang, and Q. Fang. 2020. “The influence of free water content on ballistic performances of concrete targets.” Int. J. Impact Eng. 139 (May): 103530. https://doi.org/10.1016/j.ijimpeng.2020.103530.
Jin, X., C. Hou, X. Fan, C. Lu, H. Yang, X. Shu, and Z. Wang. 2017. “Quasi-static and dynamic experimental studies on the tensile strength and failure pattern of concrete and mortar discs.” Sci. Rep. 7 (1): 15305. https://doi.org/10.1038/s41598-017-15700-2.
Li, M., H. Hao, and J. Cui. 2022. “Numerical investigation of the failure mechanism of concrete specimens under tri-axial dynamic loads.” Eng. Fract. Mech. 266 (May): 108425. https://doi.org/10.1016/j.engfracmech.2022.108425.
Li, Q. M., Y. B. Lu, and H. Meng. 2009. “Further investigation on the dynamic compressive strength enhancement of concrete-like materials based on split Hopkinson pressure bar tests. Part II: Numerical simulations.” Int. J. Impact Eng. 36 (12): 1335–1345. https://doi.org/10.1016/j.ijimpeng.2009.04.010.
Liu, B. D., W. J. Lv, L. Li, and P. F. Li. 2014. “Effect of moisture content on static compressive elasticity modulus of concrete.” Constr. Build. Mater. 69 (Oct): 133–142. https://doi.org/10.1016/j.conbuildmat.2014.06.094.
Lv, T. H., X. W. Chen, and G. Chen. 2017. “Analysis on the waveform features of the split Hopkinson pressure bar tests of plain concrete specimen.” Int. J. Impact Eng. 103 (May): 107–123. https://doi.org/10.1016/j.ijimpeng.2017.01.004.
Malvar, L. J., and C. A. Ross. 1998. “Review of strain rate effects for concrete in tension.” ACI Mater. J. 95 (6): 735–739. https://doi.org/10.14359/418.
Neville, A. M. 1996. Properties of concrete. New York: Wiley.
Pham, T. M., W. Chen, A. M. Khan, H. Hao, M. Elchalakani, and T. M. Tran. 2020a. “Dynamic compressive properties of lightweight rubberized concrete.” Constr. Build. Mater. 238 (Mar): 117705. https://doi.org/10.1016/j.conbuildmat.2019.117705.
Pham, T. M., J. Davis, N. S. Ha, E. Pournasiri, F. Shi, and H. Hao. 2021. “Experimental investigation on dynamic properties of ultra-high-performance rubberized concrete (UHPRuC).” Constr. Build. Mater. 307 (Nov): 125104. https://doi.org/10.1016/j.conbuildmat.2021.125104.
Pham, T. M., J. Liu, P. Tran, V. Pang, F. Shi, W. Chen, H. Hao, and T. M. Tran. 2020b. “Dynamic compressive properties of lightweight rubberized geopolymer concrete.” Constr. Build. Mater. 265 (Dec): 120753. https://doi.org/10.1016/j.conbuildmat.2020.120753.
Powers, T. C., and T. L. Brownyard. 2003. “Studies of the physical properties of hardened Portland cement paste.” J. Proc. 43 (9): 469–504. https://doi.org/10.14359/15302.
Ren, H., S. Song, and J. Ning. 2022. “Investigation into the damage mechanism of concrete in the Brazilian test and flattened Brazilian test through the moment tensor.” Eng. Fract. Mech. 262 (Mar): 108093. https://doi.org/10.1016/j.engfracmech.2021.108093.
Rossi, P. 1997. “Strain rate effects in concrete structures: The LCPC experience.” Mater. Struct. 30 (S1): 54–62. https://doi.org/10.1007/BF02539277.
Rossi, P. 2015. “Influence of cracking in the presence of free water on the mechanical behaviour of concrete.” Mag. Concr. Res. 43 (154): 53–57. https://doi.org/10.1680/macr.1991.43.154.53.
Rossi, P., J. G. M. van Mier, C. Boulay, and F. Le Maou. 1992. “The dynamic behaviour of concrete: Influence of free water.” Mater. Struct. 25 (9): 509–514. https://doi.org/10.1007/BF02472446.
Rossi, P., J. G. M. Van Mier, F. Toutlemonde, F. Le Maou, and C. Boulay. 1994. “Effect of loading rate on the strength of concrete subjected to uniaxial tension.” Mater. Struct. 27 (5): 260–264. https://doi.org/10.1007/BF02473042.
Shilko, E. V., I. S. Konovalenko, and I. S. Konovalenko. 2021. “Nonlinear mechanical effect of free water on the dynamic compressive strength and fracture of high-strength concrete.” Materials 14 (14): 4011. https://doi.org/10.3390/ma14144011.
Sun, X., H. Wang, X. Cheng, and Y. Sheng. 2020. “Effect of pore liquid viscosity on the dynamic compressive properties of concrete.” Constr. Build. Mater. 231 (Jan): 117143. https://doi.org/10.1016/j.conbuildmat.2019.117143.
Tedesco, J. W., and C. A. Ross. 1998. “Strain-rate-dependent constitutive equations for concrete.” J. Press. Vessel Technol. 120 (4): 398–405. https://doi.org/10.1115/1.2842350.
Vu, X. H., Y. Malecot, L. Daudeville, and E. Buzaud. 2009. “Experimental analysis of concrete behavior under high confinement: Effect of the saturation ratio.” Int. J. Solids Struct. 46 (5): 1105–1120. https://doi.org/10.1016/j.ijsolstr.2008.10.015.
Wang, H., W. Jin, and Q. Li. 2009. “Saturation effect on dynamic tensile and compressive strength of concrete.” Adv. Struct. Eng. 12 (2): 279–286. https://doi.org/10.1260/136943309788251713.
Wu, S., X. Chen, and J. Zhou. 2012. “Influence of strain rate and water content on mechanical behavior of dam concrete.” Constr. Build. Mater. 36 (Nov): 448–457. https://doi.org/10.1016/j.conbuildmat.2012.06.046.
Yan, D., and G. Lin. 2006. “Dynamic properties of concrete in direct tension.” Cem. Concr. Res. 36 (7): 1371–1378. https://doi.org/10.1016/j.cemconres.2006.03.003.
Yang, L. M., and V. P. W. Shim. 2005. “An analysis of stress uniformity in split Hopkinson bar test specimens.” Int. J. Impact Eng. 31 (2): 129–150. https://doi.org/10.1016/j.ijimpeng.2003.09.002.
Yurtdas, I., N. Burlion, and F. Skoczylas. 2004. “Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar.” Mater. Struct. 37 (3): 170–176. https://doi.org/10.1007/BF02481616.
Zhang, G., Z. Li, L. Zhang, Y. Shang, and H. Wang. 2017. “Experimental research on drying control condition with minimal effect on concrete strength.” Constr. Build. Mater. 135 (Mar): 194–202. https://doi.org/10.1016/j.conbuildmat.2016.12.141.
Zhang, X., Y. W. Chiu, H. Hao, and J. Cui. 2021. “Free water effect on the dynamic compressive properties of mortar.” Cem. Concr. Compos. 118 (Apr): 103933. https://doi.org/10.1016/j.cemconcomp.2021.103933.
Zhao, F. Q., and H. M. Wen. 2018. “Effect of free water content on the penetration of concrete.” Int. J. Impact Eng. 121 (Nov): 180–190. https://doi.org/10.1016/j.ijimpeng.2018.06.007.
Zhao, X., B. Zou, M. Wang, H. Li, and Z. Lou. 2021. “Influence of free water on dynamic tensile behavior of ultra-high toughness cementitious composites.” Constr. Build. Mater. 269 (Feb): 121295. https://doi.org/10.1016/j.conbuildmat.2020.121295.
Zheng, D., and Q. Li. 2004. “An explanation for rate effect of concrete strength based on fracture toughness including free water viscosity.” Eng. Fract. Mech. 71 (16): 2319–2327. https://doi.org/10.1016/j.engfracmech.2004.01.012.
Zhou, J., and N. Ding. 2014. “Moisture effect on compressive behavior of concrete under dynamic loading.” J. Cent. South Univ. 21 (12): 4714–4722. https://doi.org/10.1007/s11771-014-2481-7.
Zhou, Z., X. Cai, Y. Zhao, L. Chen, C. Xiong, and X. Li. 2016. “Strength characteristics of dry and saturated rock at different strain rates.” Trans. Nonferrous Met. Soc. China 26 (7): 1919–1925. https://doi.org/10.1016/S1003-6326(16)64314-5.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Jul 4, 2023
Accepted: Nov 30, 2023
Published online: Mar 26, 2024
Published in print: Jun 1, 2024
Discussion open until: Aug 26, 2024
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.