Experimental and Analytical Study of the High-Strain Rate Flexural Behavior of SFRC
Publication: Journal of Materials in Civil Engineering
Volume 36, Issue 4
Abstract
Steel fiber-reinforced concrete (SFRC) with hooked-end steel fibers was created for use in urban furniture to protect against blast and impact loads. Due to the variety of impact loads that these structures may experience, it is necessary to assess the impact of high strain rates on the flexural behavior of SFRC. This study involved testing SFRC beams with 1% volume content of hooked-end fibers, which were 30 mm long and had an aspect ratio of 80. The beams were tested at different strain rates and in a three-point loading configuration. Four strain rates were tested, ranging from to , and impact tests were conducted using a drop weight impact test machine and varying drop heights, corresponding to strain rates ranging from 1 to . Two load cells were used to measure the total impact force and one reaction force, which were then used to assess the inertial force. Two accelerometers measured the maximum acceleration at the midspan of the beams. The results included quasi-static and dynamic load-deflection relationships, dynamic flexural tensile strength, and failure mode of SFRC specimens, as well as the relationship between the inertial force and strain rate. The study revealed that deflection capacity and flexural tensile strength increased with loading rate. The study also provides dynamic to static property ratios, such as flexural tensile strength and fracture energy, which are compared with those recommended by the CEB-FIP Model Code and other researchers.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The first author gratefully acknowledges the financial support of FCT for the Ph.D. Grant SFRH/BD/149246/2019. The study reported in this paper is part of the project “FemWebAI - Integrated approach for reliable and advanced analysis and design of sustainable construction systems in fiber-reinforced concrete, with reference PTDC/ECI-EST/6300/2020, supported by the Portuguese Science Foundation (FCT).
References
Abaza, O. A., and Z. S. Hussein. 2016. “Flexural behavior of steel fiber-reinforced rubberized concrete.” J. Mater. Civ. Eng. 28 (1): 04015076. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001334.
ACI (American Concrete Institute). 1996. State-of-the-art report on fiber reinforced concrete. ACI Committee 544. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2017. Report on measuring mechanical properties of hardened fiber reinforced concrete. ACI Committee 544. Farmington Hills, MI: ACI.
Akcay, B., and M. A. Tasdemir. 2012. “Mechanical behaviour and fibre dispersion of hybrid steel fibre reinforced self-compacting concrete.” Constr. Build. Mater. 28 (1): 287–293. https://doi.org/10.1016/j.conbuildmat.2011.08.044.
Bakhshi, M., I. B. Valente, H. Ramezansefat, J. A. Barros, E. N. Pereira, and N. R. Peixinho. 2023. “Experimental and analytical study of the high-strain-rate compressive behavior of SFRC.” Mech. Adv. Mater. Struct. 1–24. https://doi.org/10.1080/15376494.2023.2199420.
Bakhshi, M., I. B. Valente, H. Ramezansefat, J. A. O. Barros, E. N. B. Pereira, and N. R. M. Peixinho. 2021. “Experimental investigation of the effect of high strain rate loading on the flexural behaviour of the steel fibre-reinforced concrete.” In Proc., fib Symp., 604–613. Braga, Portugal: Univ. of Minho.
Banthia, N., and S. Mindess. 1996. “Impact resistance of steel fiber reinforced concrete.” Mater. J. 93 (5): 472–479. https://doi.org/10.14359/9852.
Banthia, N., S. Mindess, A. Bentur, and M. Pigeon. 1989. “Impact testing of concrete using a drop-weight impact machine.” Exp. Mech. 29 (1): 63–69. https://doi.org/10.1007/BF02327783.
Banthia, N., and J.-F. Trottier. 1991. “Deformed steel fiber—Cementitious matrix bond under impact.” Cem. Concr. Res. 21 (1): 158–168. https://doi.org/10.1016/0008-8846(91)90042-G.
Banthia, N., C. Yan, and K. Sakai. 1998. “Impact resistance of fiber reinforced concrete at subnorma temperatures.” Cem. Concr. Compos. 20 (5): 393–404. https://doi.org/10.1016/S0958-9465(98)00015-8.
Banthia, N. P. 1987. Impact resistance of concrete. Vancouver, BC, Canada: Univ. of British Columbia.
Banthia, N. P., S. Mindess, and A. Bentur. 1987. “Impact behaviour of concrete beams.” Mater. Struct. 20 (4): 293–302. https://doi.org/10.1007/BF02485926.
Barros, J. A. O., I. G. Costa, C. M. V. Frazão, T. D. S. Valente, L. A. P. Lourenço, and F. J. S. A. Melo. 2022a. “Innovative prefabricated lightweight slab system of high structural performance.” Eng. Struct. 259 (Jun): 114146. https://doi.org/10.1016/j.engstruct.2022.114146.
Barros, J. A. O., and J. A. Figueiras. 1999. “Flexural behavior of SFRC: Testing and modeling.” J. Mater. Civ. Eng. 11 (4): 331–339. https://doi.org/10.1061/(ASCE)0899-1561(1999)11:4(331).
Barros, J. A. O., T. D. S. Valente, I. G. Costa, and F. J. S. A. Melo. 2022b. “Integrating hybrid reinforced concrete technology and advanced FEM-based numerical modelling for crack control in long concrete foundations without joints.” In Proc., RILEM Int. Conf. on Numerical Modeling Strategies for Sustainable Concrete Structures, 33–46. New York: Springer.
Bentur, A., and S. Mindess. 2006. Fibre reinforced cementitious composites. Boca Raton, FL: CRC Press.
Bhowmik, S., and S. Ray. 2019. “An experimental approach for characterization of fracture process zone in concrete.” Eng. Fract. Mech. 211 (Jun): 401–419. https://doi.org/10.1016/j.engfracmech.2019.02.026.
British Standard Euro Norm. 2000. Cement. Composition, specifications and conformity criteria for common cements. BS EN 197-1. London: British Standards Institute.
British Standard Euro Norm. 2012. Fly ash for concrete—Definition, specifications and conformity criteria. BS EN 450-1. London: British Standards Institute.
Caverzan, A., E. Cadoni, and M. Di Prisco. 2012. “Tensile behaviour of high performance fibre-reinforced cementitious composites at high strain rates.” Int. J. Impact Eng. 45 (Feb): 28–38. https://doi.org/10.1016/j.ijimpeng.2012.01.006.
CEB-FIP (Comité européen du béton-Fédération Internationale de la Précontrainte). 1990. Design code 1990, 51–59. London: Thomas Telford.
CEB-FIP (Comité européen du béton-Fédération Internationale de la Précontrainte). 2010. Model code 2010. London: Thomas Telford.
Fujikake, K., T. Senga, N. Ueda, T. Ohno, and M. Katagiri. 2006. “Effects of strain rate on tensile behavior of reactive powder concrete.” J. Adv. Concr. Technol. 4 (1): 79–84. https://doi.org/10.3151/jact.4.79.
Gao, X., T. C. K. Molyneaux, I. Patnaikuni, and S. M. S. Rahman. 2020. “Dynamic properties of fibre reinforced and plain ultra high performance concretes.” In Proc., Int. Conf. Innovation Good Practice and Research in Engineering Education, 569–573. Boca Raton, FL: CRC Press.
Gopalaratnam, V. S., and S. P. Shah. 1986. “Properties of steel fiber reinforced concrete subjected to impact loading.” ACI J. 83 (1): 117–126.
Jin, L., R. Zhang, G. Dou, J. Xu, and X. Du. 2018. “Experimental and numerical study of reinforced concrete beams with steel fibers subjected to impact loading.” Int. J. Damage Mech. 27 (7): 1058–1083. https://doi.org/10.1177/1056789517721616.
Körmeling, H. A., and H. W. Reinhardt. 1987. “Strain rate effects on steel fibre concrete in uniaxial tension.” Int. J. Cem. Compos. Lightweight Concr. 9 (4): 197–204. https://doi.org/10.1016/0262-5075(87)90002-9.
Lok, T. S., X. B. Li, D. Liu, and P. J. Zhao. 2002. “Testing and response of large diameter brittle materials subjected to high strain rate.” J. Mater. Civ. Eng. 14 (3): 262–269. https://doi.org/10.1061/(ASCE)0899-1561(2002)14:3(262).
Lok, T. S., and P. J. Zhao. 2004. “Impact response of steel fiber-reinforced concrete using a split Hopkinson pressure bar.” J. Mater. Civ. Eng. 16 (1): 54–59. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:1(54).
Lok, T. S., P. J. Zhao, and G. Lu. 2003. “Using the split Hopkinson pressure bar to investigate the dynamic behaviour of SFRC.” Mag. Concr. Res. 55 (2): 183–191. https://doi.org/10.1680/macr.2003.55.2.183.
Malvar, L. J., and C. A. Ross. 1998. “Review of strain rate effects for concrete in tension.” ACI Mater. J. 95 (Jun): 735–739. https://doi.org/10.14359/418.
Millard, S. G., T. C. K. Molyneaux, S. J. Barnett, and X. Gao. 2010. “Dynamic enhancement of blast-resistant ultra high performance fibre-reinforced concrete under flexural and shear loading.” Int. J. Impact Eng. 37 (4): 405–413. https://doi.org/10.1016/j.ijimpeng.2009.09.004.
Mujalli, M. A., S. Dirar, E. Mushtaha, A. Hussien, and A. Maksoud. 2022. “Evaluation of the tensile characteristics and bond behaviour of steel fibre-reinforced concrete: An overview.” Fibers 10 (12): 104. https://doi.org/10.3390/fib10120104.
Naaman, A. E., and V. S. Gopalaratnam. 1983. “Impact properties of steel fibre reinforced concrete in bending.” Int. J. Cem. Compos. Lightweight Concr. 5 (4): 225–233. https://doi.org/10.1016/0262-5075(83)90064-7.
Nyström, U., and K. Gylltoft. 2009. “Numerical studies of the combined effects of blast and fragment loading.” Int. J. Impact Eng. 36 (8): 995–1005. https://doi.org/10.1016/j.ijimpeng.2009.02.008.
Othman, H., and H. Marzouk. 2016. “An experimental investigation on the effect of steel reinforcement on impact response of reinforced concrete plates.” Int. J. Impact Eng. 88 (Apr): 12–21. https://doi.org/10.1016/j.ijimpeng.2015.08.015.
Othman, H., H. Marzouk, and M. Sherif. 2019. “Effects of variations in compressive strength and fibre content on dynamic properties of ultra-high performance fibre-reinforced concrete.” Constr. Build. Mater. 195 (Jun): 547–556. https://doi.org/10.1016/j.conbuildmat.2018.11.093.
Ozden, G., and C. T. Akdag. 2009. “Lateral load response of steel fiber reinforced concrete model piles in cohesionless soil.” Constr. Build. Mater. 23 (2): 785–794. https://doi.org/10.1016/j.conbuildmat.2008.03.001.
Park, J., S. Yoon, T.-H. Kwon, and K. Park. 2017. “Assessment of speckle-pattern quality in digital image correlation based on gray intensity and speckle morphology.” Opt. Lasers Eng. 91 (Apr): 62–72. https://doi.org/10.1016/j.optlaseng.2016.11.001.
Poveda, E., R. C. Yu, M. Tarifa, G. Ruiz, V. M. C. F. Cunha, and J. A. O. Barros. 2020. “Rate effect in inclined fibre pull-out for smooth and hooked-end fibres: A numerical study.” Int. J. Fract. 223 (1): 135–149. https://doi.org/10.1007/s10704-019-00404-7.
Rahmani, T., B. Kiani, M. Shekarchi, and A. Safari. 2012. “Statistical and experimental analysis on the behavior of fiber reinforced concretes subjected to drop weight test.” Constr. Build. Mater. 37 (Aug): 360–369. https://doi.org/10.1016/j.conbuildmat.2012.07.068.
Rasheed, M. A., and S. S. Prakash. 2018. “Behavior of hybrid-synthetic fiber reinforced cellular lightweight concrete under uniaxial tension–Experimental and analytical studies.” Constr. Build. Mater. 162 (Jun): 857–870. https://doi.org/10.1016/j.conbuildmat.2017.12.095.
RILEM 50-FMC Committee. 1985. “Determination of the fracture energy of mortar and concrete by means of three-point bend tests on notched beams.” Mater. Struct. 18 (106): 285–290.
Sorelli, L. G., A. Meda, and G. A. Plizzari. 2006. “Steel fiber concrete slabs on ground: A structural matter.” ACI Mater. J. 103 (4): 551. https://doi.org/10.14359/16431.
Suaris, W., and S. P. Shah. 1982. “Strain-rate effects in fibre-reinforced concrete subjected to impact and impulsive loading.” Composites 13 (2): 153–159. https://doi.org/10.1016/0010-4361(82)90052-0.
Suaris, W., and S. P. Shah. 1983. “Properties of concrete subjected to impact.” J. Struct. Eng. 109 (7): 1727–1741. https://doi.org/10.1061/(ASCE)0733-9445(1983)109:7(1727).
Taheri, M., J. A. O. Barros, and H. Salehian. 2020. “Integrated approach for the prediction of crack width and spacing in flexural FRC members with hybrid reinforcement.” Eng. Struct. 209 (Aug): 110208. https://doi.org/10.1016/j.engstruct.2020.110208.
Tarifa, M., E. Poveda, V. M. C. F. Cunha, and J. A. O. Barros. 2020. “Effect of the displacement rate and inclination angle in steel fiber pullout tests.” Int. J. Fract. 223 (1): 109–122. https://doi.org/10.1007/s10704-019-00398-2.
Tedesco, J. W., and C. A. Ross. 1998. “Strain-rate-dependent constitutive equations for concrete.” J. Pressure Vessel Technol. 120 (4): 398–405. https://doi.org/10.1115/1.2842350.
Tlemat, H., K. Pilakoutas, and K. Neocleous. 2003. “Flexural toughness of SFRC made with fibres extracted from tyres.” In Proc., Int. Symp. Advances in Recycling & Waste Management, 365–374. London: Thomas Telford.
Tran, N. T., T. K. Tran, J. K. Jeon, J. K. Park, and D. J. Kim. 2016. “Fracture energy of ultra-high-performance fiber-reinforced concrete at high strain rates.” Cem. Concr. Res. 79 (Feb): 169–184. https://doi.org/10.1016/j.cemconres.2015.09.011.
Tran, T. K., and D. J. Kim. 2013. “Investigating direct tensile behavior of high performance fiber reinforced cementitious composites at high strain rates.” Cem. Concr. Res. 50 (Jan): 62–73. https://doi.org/10.1016/j.cemconres.2013.03.018.
Ulzurrun, G., and C. Zanuy. 2017. “Flexural response of SFRC under impact loading.” Constr. Build. Mater. 134 (Aug): 397–411. https://doi.org/10.1016/j.conbuildmat.2016.12.138.
Vandewalle, L., et al. 2022. “Test and design methods for steel fibre reinforced concrete—Final recommendation.” Mater. Struct. 35 (253): 579–582.
Wang, S., M.-H. Zhang, and S. T. Quek. 2011. “Effect of high strain rate loading on compressive behaviour of fibre-reinforced high-strength concrete.” Mag. Concr. Res. 63 (11): 813–827. https://doi.org/10.1680/macr.2011.63.11.813.
Weerheijm, J., and P. Forquin. 2013. “Response mechanisms of concrete under impulsive tensile loading.” In Understanding the tensile properties of concrete, 181–217. Amsterdam, Netherlands: Elsevier.
Wu, H., Q. Fang, J. Gong, J. Z. Liu, J. H. Zhang, and Z. M. Gong. 2015. “Projectile impact resistance of corundum aggregated UHP-SFRC.” Int. J. Impact Eng. 84 (Jun): 38–53. https://doi.org/10.1016/j.ijimpeng.2015.05.007.
Xu, S., C. Wu, Z. Liu, K. Han, Y. Su, J. Zhao, and J. Li. 2017. “Experimental investigation of seismic behavior of ultra-high performance steel fiber reinforced concrete columns.” Eng. Struct. 152 (Feb): 129–148. https://doi.org/10.1016/j.engstruct.2017.09.007.
Yoo, D.-Y., and N. Banthia. 2017. “Size-dependent impact resistance of ultra-high-performance fiber-reinforced concrete beams.” Constr. Build. Mater. 142 (May): 363–375. https://doi.org/10.1016/j.conbuildmat.2017.03.080.
Yoo, D.-Y., and N. Banthia. 2019. “Impact resistance of fiber-reinforced concrete—A review.” Cem. Concr. Compos. 104 (Aug): 103389. https://doi.org/10.1016/j.cemconcomp.2019.103389.
Yoo, D.-Y., S.-T. Kang, and Y.-S. Yoon. 2016. “Enhancing the flexural performance of ultra-high-performance concrete using long steel fibers.” Compos. Struct. 147 (Feb): 220–230. https://doi.org/10.1016/j.compstruct.2016.03.032.
Yoo, D.-Y., Y.-S. Yoon, and N. Banthia. 2015. “Flexural response of steel-fiber-reinforced concrete beams: Effects of strength, fiber content, and strain-rate.” Cem. Concr. Compos. 64 (Jan): 84–92. https://doi.org/10.1016/j.cemconcomp.2015.10.001.
Zanuy, C., and G. S. D. Ulzurrún. 2017. “Rate effects of fiber-reinforced concrete specimens in impact regime.” Procedia Eng. 193 (Feb): 501–508. https://doi.org/10.1016/j.proeng.2017.06.243.
Zhang, X., G. Ruiz, M. Tafira, and D. A. Cendon. 2015. “Loading rate effect on the fracture behaviour of three different steel fiber-reinforced concretes.” In Proc., 9th Int. Conf. FraMCoS-9, edited by V. Sauoma, J. Bolander, and E. Landis. Los Angeles: Univ. of California.
Zhang, X., G. Ruiz, M. Tarifa, D. Cendón, F. Gálvez, and W. H. Alhazmi. 2017. “Dynamic fracture behavior of steel fiber reinforced self-compacting concretes (SFRSCCs).” Materials 10 (11): 1270. https://doi.org/10.3390/ma10111270.
Zhang, X. X., A. M. Abd Elazim, G. Ruiz, and R. C. Yu. 2014. “Fracture behaviour of steel fibre-reinforced concrete at a wide range of loading rates.” Int. J. Impact Eng. 71 (Jan): 89–96. https://doi.org/10.1016/j.ijimpeng.2014.04.009.
Zhang, X. X., G. Ruiz, R. C. Yu, and M. Tarifa. 2009. “Fracture behaviour of high-strength concrete at a wide range of loading rates.” Int. J. Impact Eng. 36 (10–11): 1204–1209. https://doi.org/10.1016/j.ijimpeng.2009.04.007.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 36 • Issue 4 • April 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Mar 2, 2023
Accepted: Oct 2, 2023
Published online: Jan 27, 2024
Published in print: Apr 1, 2024
Discussion open until: Jun 27, 2024
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.