Thermal Response of Energy Screw Piles Connected in Series
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 149, Issue 7
Abstract
Energy piles are a consolidated underground heat exchanger alternative to traditional boreholes in ground source heat pump (GSHP) systems. Previous works focused on assessing the differences between piles and boreholes, but few assessed small piles in operational conditions. Moreover, most of these studies centered around cylindrical concrete piles, overlooking short screw piles. Using in-situ testing, established analytical methods, and advanced three dimensional (3D) finite element model simulations, this work assesses three thermal response tests (TRT) executed in different energy pile structures, one being a unique group of eight short energy screw piles connected in series, located in the same site in Melbourne, Australia. Detailed numerical analysis provided reliable soil and structure thermal parameter predictions and detailed computations allowed the study of thermal effects for the energy screw piles steel components. The results show limited impact of the steel components on effective thermal conductivity, but a reduction in thermal resistivity that may provide a speedier thermal exchange in short term GSHP operation. In addition, the more traditional TRT rigs and analytical interpretation provided reasonable results for the pile group in series, and show a similar performance to a borehole heat exchanger of similar pipe length; however, the short piles engage only the upper soil layers, with potentially lower thermal conductivity. TRT in single short screw piles require careful consideration, because common rigs may be unable to cater for the required low fluid flow rates and heating power. Thus, for the cases assessed herein, the pile group TRT proved to be more reliable than individual pile testing, due to their short length.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors acknowledge the contribution from GeoExchange Australia, Hutchison Builders, and PICAC leadership for providing access to the energy structures. Funding from the Australian Research Council (Project No. LP160101486) and the University of Melbourne is much appreciated. Assistance from Lawrence Hanson, Benjamin Robertson, Wayne Chan, Kieran Joseph Sait, Dr. Gregorius Riyan Aditya, and Dr. Linden Jensen-Page in the fieldwork is acknowledged and appreciated.
References
Abdelaziz, S. L., C. G. Olgun, and J. R. Martin. 2015. “Counterbalancing ambient interference on thermal conductivity tests for energy piles.” Geothermics 56 (Jul): 45–59. https://doi.org/10.1016/j.geothermics.2015.03.005.
Adam, D., and R. Markiewicz. 2009. “Energy from earth-coupled structures, foundations, tunnels and sewers.” Géotechnique 59 (3): 229–236. https://doi.org/10.1680/geot.2009.59.3.229.
Alberdi-Pagola, M., S. E. Poulsen, F. Loveridge, S. Madsen, and R. L. Jensen. 2018. “Comparing heat flow models for interpretation of precast quadratic pile heat exchanger thermal response tests.” Energy 145 (Feb): 721–733. https://doi.org/10.1016/j.energy.2017.12.104.
Amatya, B. L., K. Soga, P. J. Bourne-Webb, T. Amis, and L. Laloui. 2012. “Thermo-mechanical behaviour of energy piles.” Géotechnique 62 (6): 503–519. https://doi.org/10.1680/geot.10.P.116.
ARENA (Australian Renewable Energy Agency). 2014. Looking forward: Barriers, risks and rewards of the Australian geothermal sector to 2020 and 2030. Canberra, Australia: ARENA.
Arulrajah, A., G. Narsilio, J. Kodikara, and R. P. Orense. 2015. “Key issues in environmental geotechnics: Australia–New Zealand.” Environ. Geotech. 2 (6): 326–330. https://doi.org/10.1680/envgeo.14.00005.
Asadi, I., P. Shafigh, Z. F. B. Abu Hassan, and N. B. Mahyuddin. 2018. “Thermal conductivity of concrete: A review.” J. Build. Eng. 20 (Nov): 81–93. https://doi.org/10.1016/j.jobe.2018.07.002.
ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers). 2001. Methods for determining soil and rock formation thermal properties from field tests. Atlanta, GA: ASHRAE.
Austin, W. A., III. 1998. “Development of an in situ system for measuring ground thermal properties.” M.Sc. thesis, Faculty of the Graduate College, Oklahoma State Univ.
Bandeira Neto, L., G. Narsilio, N. Makasis, L. Hanson, R. Benjamin, and Y. Carden. 2022. “Evaluation of analytical design methods for energy pile groups using a screw-pile case study in Australia.” In Proc., 20th Int. Conf. on Soil Mechanics and Geotechnical Engineering Proceedings, 4989–4994. Perth, WA, Australia: Australian Geomechanics Society.
Barry-Macaulay, D., A. Bouazza, R. M. Singh, B. Wang, and P. G. Ranjith. 2013. “Thermal conductivity of soils and rocks from the Melbourne (Australia) region.” Eng. Geol. 164 (17): 131–138. https://doi.org/10.1016/j.enggeo.2013.06.014.
Beier, R. A., and M. D. Smith. 2002. “Borehole thermal resistance from line-source model of in-situ tests.” ASHRAE Trans. 108 (2): 212–219.
Bidarmaghz, A. 2014. “3D numerical modelling of vertical ground heat exchangers.” Ph.D. thesis, Dept. of Infrastructure Engineering, Univ. of Melbourne.
Bidarmaghz, A., N. Makasis, G. A. Narsilio, F. M. Francisca, and M. E. Carro Pérez. 2016. “Geothermal energy in loess.” Environ. Geotech. 3 (4): 225–236. https://doi.org/10.1680/jenge.15.00025.
Brandl, H. 2006. “Energy foundations and other thermo-active ground structures.” Géotechnique 56 (2): 81–122. https://doi.org/10.1680/geot.2006.56.2.81.
Brettmann, T., and T. Amis. 2011. “Thermal conductivity evaluation of a pile group using geothermal energy piles.” In Geo-Frontiers Congress, 499–508. Reston, VA: ASCE. https://doi.org/10.1061/41165(397)52.
Carslaw, H., and J. Jaeger. 1959. Conduction of heat in solids. Oxford, UK: Clarendon.
Cecinato, F., and F. A. Loveridge. 2015. “Influences on the thermal efficiency of energy piles.” Energy 82 (Mar): 1021–1033. https://doi.org/10.1016/j.energy.2015.02.001.
Chan, W., and K. J. Sait. 2018. Performance and cost comparison of a single borehole and series-connected screw-pile ground heat exchangers: A case study in Melbourne. Melbourne, Australia: Univ. of Melbourne.
Cimmino, M., and M. Bernier. 2014. “A semi-analytical method to generate -functions for geothermal bore fields.” Int. J. Heat Mass Transfer 70 (Mar): 641–650. https://doi.org/10.1016/j.ijheatmasstransfer.2013.11.037.
Colls, S. 2013. “Ground heat exchanger design for direct geothermal energy systems.” Ph.D. thesis, Dept. of Infrastructure Engineering, Univ. of Melbourne.
COMSOL. 2020. “Introduction to Pipe Flow Module.” In COMSOL Multiphysics® v. 5.6, 1–21. Stockholm, Sweden: COMSOL AB.
Delerablee, Y., S. Burlon, and P. Reiffsteck. 2019. “Long term assessment of thermal sustainability of thermoactive geostructures.” Environ. Geotech. 7 (4): 249–265. https://doi.org/10.1680/jenge.17.00102.
Di Donna, A., and L. Laloui. 2015. “Numerical analysis of the geotechnical behaviour of energy piles.” Int. J. Numer. Anal. Methods Geomech. 39 (8): 861–888. https://doi.org/10.1002/nag.2341.
EklöF, C., and S. Gehlin. 1996. “A mobile equipment for thermal response test.” M.Sc. thesis, Dept. of Environmmental Planning and Design, Luleå Univ. of Technology.
Eskilson, P. 1987. “Thermal analysis of heat extraction boreholes.” Ph.D. thesis, Dept. of Technical Physics, Univ. of Lund.
Faizal, M., A. Bouazza, and R. M. Singh. 2016. “Heat transfer enhancement of geothermal energy piles.” Renewable Sustainable Energy Rev. 57 (May): 16–33. https://doi.org/10.1016/j.rser.2015.12.065.
Faizal, M., A. Moradshahi, A. Bouazza, and J. S. McCartney. 2022. “Soil thermal response to temperature cycles and end boundary conditions of energy piles.” J. Geotech. Geoenviron. Eng. 148 (5): 04022027. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002794.
Fei, W., G. A. Narsilio, and M. M. Disfani. 2021. “Predicting effective thermal conductivity in sands using an artificial neural network with multiscale microstructural parameters.” Int. J. Heat Mass Transfer 170 (May): 120997. https://doi.org/10.1016/j.ijheatmasstransfer.2021.120997.
Franco, A., and P. Conti. 2020. “Clearing a path for ground heat exchange systems: A review on thermal response test (TRT) methods and a geotechnical routine test for estimating soil thermal properties.” Energies 13 (11): 2965. https://doi.org/10.3390/en13112965.
Franco, A., R. Moffat, M. Toledo, and P. Herrera. 2016. “Numerical sensitivity analysis of thermal response tests (TRT) in energy piles.” Renewable Energy 86 (Feb): 985–992. https://doi.org/10.1016/j.renene.2015.09.019.
Hanson, L., and B. Robertson. 2018. Thermal performance of energy screw piles in series. Melbourne, Australia: Univ. of Melbourne.
Huang, J., J. S. McCartney, H. Perko, D. Johnson, C. Zheng, and Q. Yang. 2019. “A novel energy pile: The thermo-syphon helical pile.” Appl. Therm. Eng. 159 (Aug): 113882. https://doi.org/10.1016/j.applthermaleng.2019.113882.
Insana, A., and M. Barla. 2020. “Experimental and numerical investigations on the energy performance of a thermo-active tunnel.” Renewable Energy 152 (Jun): 781–792. https://doi.org/10.1016/j.renene.2020.01.086.
Jalaluddin, A. Miyara, K. Tsubaki, S. Inoue, and K. Yoshida. 2011. “Experimental study of several types of ground heat exchanger using a steel pile foundation.” Renewable Energy 36 (2): 764–771. https://doi.org/10.1016/j.renene.2010.08.011.
Jensen-Page, L., F. Loveridge, and G. A. Narsilio. 2019. “Thermal response testing of large diameter energy piles.” Energies 12 (14): 2700. https://doi.org/10.3390/en12142700.
Jensen-Page, L., G. A. Narsilio, A. Bidarmaghz, and I. W. Johnston. 2018. “Investigation of the effect of seasonal variation in ground temperature on thermal response tests.” Renewable Energy 125 (Sep): 609–619. https://doi.org/10.1016/j.renene.2017.12.095.
Johnston, I. W., G. A. Narsilio, and S. Colls. 2011. “Emerging geothermal energy technologies.” KSCE J. Civ. Eng. 15 (4): 643–653. https://doi.org/10.1007/s12205-011-0005-7.
Katsura, T., K. Nagano, S. Narita, S. Takeda, Y. Nakamura, and A. Okamoto. 2009. “Calculation algorithm of the temperatures for pipe arrangement of multiple ground heat exchangers.” Appl. Therm. Eng. 29 (5–6): 906–919. https://doi.org/10.1016/j.applthermaleng.2008.04.026.
Kim, D., and S. Oh. 2019. “Relationship between the thermal properties and degree of saturation of cementitious grouts used in vertical borehole heat exchangers.” Energy Build. 201 (Oct): 1–9. https://doi.org/10.1016/j.enbuild.2019.07.017.
Laloui, L., and A. D. Donna. 2011. “Understanding the behaviour of energy geo-structures.” Proc. Inst. Civ. Eng. Civ. Eng. 164 (4): 184–191. https://doi.org/10.1680/cien.2011.164.4.184.
Laloui, L., and B. François. 2009. “ACMEG-T: Soil thermoplasticity model.” J. Eng. Mech. 135 (9): 932–944. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000011.
Lamarche, L., and B. Beauchamp. 2007. “A new contribution to the finite line-source model for geothermal boreholes.” Energy Build. 39 (2): 188–198. https://doi.org/10.1016/j.enbuild.2006.06.003.
Lee, C. K. 2011. “Effects of multiple ground layers on thermal response test analysis and ground-source heat pump simulation.” Appl. Energy 88 (12): 4405–4410. https://doi.org/10.1016/j.apenergy.2011.05.023.
Loveridge, F., J. Low, and W. Powrie. 2017. “Site investigation for energy geostructures.” Q. J. Eng. Geol. Hydrogeol. 50 (2): 158–168. https://doi.org/10.1144/qjegh2016-027.
Loveridge, F., J. S. McCartney, G. A. Narsilio, and M. Sanchez. 2020. “Energy geostructures: A review of analysis approaches, in situ testing and model scale experiments.” Geomech. Energy Environ. 22 (May): 100173. https://doi.org/10.1016/j.gete.2019.100173.
Loveridge, F., C. G. Olgun, T. Brettmann, and W. Powrie. 2015a. “The thermal behaviour of three different auger pressure grouted piles used as heat exchangers.” Geotech. Geol. Eng. 33 (2): 273–289. https://doi.org/10.1007/s10706-014-9757-4.
Loveridge, F., and W. Powrie. 2013. “Temperature response functions (G-functions) for single pile heat exchangers.” Energy 57 (Aug): 554–564. https://doi.org/10.1016/j.energy.2013.04.060.
Loveridge, F., and W. Powrie. 2014. “G-Functions for multiple interacting pile heat exchangers.” Energy 64 (Jan): 747–757. https://doi.org/10.1016/j.energy.2013.11.014.
Loveridge, F. A., C. G. Olgun, T. Brettmann, and W. Powrie. 2015b. “Group thermal response testing for energy piles.” In Geotechnical Engineering for Infrastructure and Development—Proc., XVI European Conf. on Soil Mechanics and Geotechnical Engineering, 2595–2600. Edinburgh, Scotland: ICE Publishing.
Lu, Q., and G. A. Narsilio. 2019. “Cost effectiveness of energy piles in residential dwellings in Australia.” Curr. Trends Civ. Struct. Eng. 3 (3): 1–6. https://doi.org/10.33552/CTCSE.2019.03.000564.
Lund, J., and T. Boyd. 2016. “Direct utilization of geothermal energy 2015 worldwide review.” Geothermics 60 (Mar): 66–93. https://doi.org/10.1016/j.geothermics.2015.11.004.
Makasis, N. 2019. “Further understanding ground source heat pump system design using finite element methods and machine learning techniques.” Ph.D. thesis, Dept. of Infrastructure Engineering, Univ. of Melbourne.
Makasis, N., and G. A. Narsilio. 2020. “Energy diaphragm wall thermal design: The effects of pipe configuration and spacing.” Renewable Energy 154 (Jul): 476–487. https://doi.org/10.1016/j.renene.2020.02.112.
Makasis, N., G. A. Narsilio, and A. Bidarmaghz. 2018a. “A robust prediction model approach to energy geo-structure design.” Comput. Geotech. 104 (Dec): 140–151. https://doi.org/10.1016/j.compgeo.2018.08.012.
Makasis, N., G. A. Narsilio, A. Bidarmaghz, and I. W. Johnston. 2018b. “Ground-source heat pump systems: The effect of variable pipe separation in ground heat exchangers.” Comput. Geotech. 100 (Aug): 97–109. https://doi.org/10.1016/j.compgeo.2018.02.010.
Murphy, K. D., J. S. McCartney, and K. S. Henry. 2014. “Impact of horizontal run-out length on the thermal response of full-scale energy foundations.” In Proc., Geo-Congress 2014 Technical Papers, 2715–2724. Reston, VA: ASCE. https://doi.org/10.1061/9780784413272.262.
Peck, W., J. Neilson, R. Olds, and K. Seddon. 1992. Engineering geology of Melbourne. London: Routledge. https://doi.org/10.1201/9780203757413.
Raymond, J., and L. Lamarche. 2013. “Simulation of thermal response tests in a layered subsurface.” Appl. Energy 109 (Sep): 293–301. https://doi.org/10.1016/j.apenergy.2013.01.033.
Rotta Loria, A. F., A. Gunawan, C. Shi, L. Laloui, and C. W. W. Ng. 2015. “Numerical modelling of energy piles in saturated sand subjected to thermo-mechanical loads.” Geomech. Energy Environ. 1 (Apr): 1–15. https://doi.org/10.1016/j.gete.2015.03.002.
Schjønning, P. 2021. “Thermal conductivity of undisturbed soil: Measurements and predictions.” Geoderma 402 (Nov): 115188. https://doi.org/10.1016/j.geoderma.2021.115188.
Signorelli, S., S. Bassetti, D. Pahud, and T. Kohl. 2007. “Numerical evaluation of thermal response tests.” Geothermics 36 (2): 141–166. https://doi.org/10.1016/j.geothermics.2006.10.006.
Singh, R. M., A. K. Sani, and T. Amis. 2019. “An overview of ground-source heat pump technology.” Ch. 15 in Managing global warming, edited by T. M. Letcher, 455–485. London: Academic Press. https://doi.org/10.1016/B978-0-12-814104-5.00015-6.
Vieira, A., et al. 2017. “Characterisation of ground thermal and thermo-mechanical behaviour for shallow geothermal energy applications.” Energies 10 (12): 2044. https://doi.org/10.3390/en10122044.
Witte, H. J. L. 2016. “In situ estimation of ground thermal properties.” Ch. 4 in Advances in ground-source heat pump systems, edited by S. J. Rees, 97–116. Duxford, UK: Woodhead. https://doi.org/10.1016/B978-0-08-100311-4.00004-2.
Zeng, H. Y., N. R. Diao, and Z. H. Fang. 2002. “A finite line-source model for boreholes in geothermal heat exchangers.” Heat Trans. Asian Res. 31 (7): 558–567. https://doi.org/10.1002/htj.10057.
Zhang, J., D. Dias, Q. Pan, C. Ma, and C. D. H. C. Tsuha. 2022. “Long-term thermo-hydraulic numerical assessment of thermo-active piles: A case of tropical soils.” Appl. Sci. 12 (15): 7653. https://doi.org/10.3390/app12157653.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 149 • Issue 7 • July 2023
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jun 6, 2022
Accepted: Nov 28, 2022
Published online: May 5, 2023
Published in print: Jul 1, 2023
Discussion open until: Oct 5, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.