Reliability-Based Load Requirements for Formwork Shores during Concrete Placement
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 142, Issue 1
Abstract
One challenge in assessing the safety of concrete formwork supporting structures is the difficulty in predicting the loads on shores. Very limited studies on shore loads are available in the literature. This paper presents the results of a shore load investigation undertaken at three construction sites in Sydney. The study is focused on the vertical loads on shores during and following concrete placement. The statistical characteristics of the dead load effect and live load effect are determined. Structural reliability analyses are conducted to evaluate the reliability implications of the allowable stress design and limit state design approaches for shoring structures. An optimal load combination is derived considering the probabilistic characteristics of shore loads.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research is supported by Australian Research Council under Linkage Grant LP0884156. This support is gratefully acknowledged. The writers would like to thank Acro Formwork and Scaffolding for providing site access to procure the shore load survey data.
References
ACI (American Concrete Institute). (2004). “Guide to formwork for concrete.”, Farmington Hills, MI.
Agarwal, R. K., and Gardner, N. J. (1974). “Form and shore requirements for multistory flat slab type buildings.” ACI J., 71(11), 559–569.
Bjorhovde, R., Galambos, T. V., and Ravindra, M. K. (1978). “LRFD criteria for steel beam-columns.” J. Struct. Div., 104(ST9), 1371–1387.
Carper, K. L. (1987). “Structural failures during construction.” J. Perform. Constr. Facil., 132–144.
Ellingwood, B. R. (1994). “Probability-based codified design: Past accomplishments and future challenges.” Struct. Saf., 13(3), 159–176.
Ellingwood, B. R., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American National Standard A58.”, National Bureau of Standards, Washington, DC.
Ellingwood, B. R., MacGregor, J. G., Galambos, T. V., and Cornell, C. A. (1982). “Probability based load criteria: Load factors and load combinations.” J. Struct. Div., 108(5), 978–997.
Epaarachchi, D. C., Stewart, M. G., and Rosowsky, D. V. (2002). “Structural reliability of multistory buildings during construction.” J. Struct. Eng., 205–213.
Fattal, S. (1983). “Evaluation of construction loads in multistory concrete buildings.”, National Bureau of Standards, Washington, DC.
Ferguson, S. (2001). “Formwork shore design loads: An evaluation of current practice.” Concrete, 35(5), 28–30.
Hadipriono, F. C., and Wang, H. K. (1987). “Causes of falsework collapses during construction.” Struct. Saf., 4(3), 179–195.
Ikäheimonen, J. (1997). “Construction loads on shores and stability of horizontal formworks.” Ph.D. thesis, Royal Institute of Technology, Stockholm, Sweden.
Karshenas, S., and Ayoub, H. (1994a). “Analysis of concrete construction live loads on newly poured slabs.” J. Struct. Eng., 1525–1542.
Karshenas, S., and Ayoub, H. (1994b). “Construction live loads on slab formworks before concrete placement.” Struct. Saf., 14(3), 155–172.
Kothekar, A. V., Rosowsky, D. V., and Huston, D. R. (1998). “Investigating the adequacy of vertical design loads for shoring.” J. Perform. Constr. Facil., 41–47.
Liu, H., Chen, Z., Wang, X., and Zhou, T. (2010). “Theoretical analysis and experimental research on stability behaviour of structural steel tubes and coupler falsework with X-bracing.” Adv. Steel Constr., 6(4), 949–962.
Melchers, R. E. (1999). Structural reliability analysis and prediction, 2nd Ed., Wiley, West Sussex, England.
Peng, J. L., Chan, S. L., and Wu, C. L. (2007). “Effects of geometrical shape and incremental loads on scaffold systems.” J. Constr. Steel Res., 63(4), 448–459.
Puente, I., Azkune, M., and Insausti, A. (2007). “Shore-slab interaction in multistory reinforced concrete buildings during construction: An experimental approach.” Eng. Struct., 29(5), 731–741.
Rosowsky, D. V., Huang, Y. L., Chen, W. F., and Yen, T. (1994). “Modeling concrete placement loads during construction.” Struct. Eng. Rev., 6(2), 71–84.
Rosowsky, D. V., Philbrick, T. W., Jr., and Huston, D. R. (1997). “Observations from shore load measurements during concrete construction.” J. Perform. Constr. Facil., 18–23.
Standards Australia. (1995). “Australian standard AS3610-1995 formwork for concrete.” Sydney, Australia.
Yu, W. K., Chung, K. F., and Chan, S. L. (2004). “Structural instability of multi-storey door-type modular steel scaffolds.” Eng. Struct., 26(7), 867–881.
Zhang, H., Chandrangsu, T., and Rasmussen, K. J. R. (2010). “Probabilistic study of the strength of steel scaffold systems.” Struct. Saf., 32(6), 393–401.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Aug 7, 2014
Accepted: Jun 2, 2015
Published online: Jul 6, 2015
Discussion open until: Dec 6, 2015
Published in print: Jan 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.