Flexural Performance of Nanomodified Cementitious Composites Reinforced with BFP in Bonded Overlays
Publication: Journal of Materials in Civil Engineering
Volume 34, Issue 8
Abstract
There is strong demand for ductile cement-based materials in various rehabilitation systems of concrete infrastructure. This study investigated the flexural performance of nanomodified cementitious composites incorporating a novel class of basalt macrofibers, basalt-fiber pellets (BFP), in an overlay system. The cementitious composites comprised 50% fly ash or slag replacement with 6% nanosilica and 4.5% BFP. The cementitious composites [top (overlay) layer] were evaluated based on mechanical compatibility with intact and precracked concrete substrate (bottom layer) through flexural loading. In addition, three-dimensional finite-element models were established for these configurations to analyze the effect of overlay thickness and substrate compressive strength on the performance of the overlay systems. The results showed effective bonding of the composites with the substrate (without transverse delamination) and highlighted their contribution to enhancing the postcracking performance of the overlay system, in which the intact system of Specimens N-F-4.5 and N-G-4.5 had toughness 324% and 471%, respectively, higher than that of reference concrete specimens. Numerical analysis showed the influence of overlay thickness on the ductility of both systems (intact and precracked), whereas the substrate strength affected only the first-cracking strength of the intact system (approximately 25%, increasing the compressive strength of the substrate concrete from 40 to 50 MPa).
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors appreciate the financial support from the Natural Sciences and Engineering Research Council of Canada (NSERC RGPIN/2014-2020) and the University of Manitoba Research Grants Program (URGP 2019/2020).
References
ACI (American Concrete Institute). 2014. Concrete repair guide. ACI PRC-546R-14. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2018. Report on the use of fly ash in concrete. ACI-232.2R-18. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2020. Concrete overlays for pavement rehabilitation (Reapproved 2020). ACI PRC-325.13-06. Farmington Hills, MI: ACI.
ASCE. 2021. Report card for America’s infrastructure—2021. Reston, VA: ASCE.
ASTM. 2019. Standard test method for flexural performance of fiber-reinforced concrete (using beam with third-point loading). ASTM C1609/C1609M -19. West Conshohocken, PA: ASTM.
ASTM. 2021. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39/C39M-21. West Conshohocken, PA: ASTM.
Azzam, A., M. T. Bassuoni, and A. Shalaby. 2019. “Properties of high-volume fly ash and slag cementitious composites incorporating nanosilica and basalt fiber pellets.” Adv. Civ. Eng. Mater. 8 (3): 255–274. https://doi.org/10.1520/ACEM20190018.
Azzam, A., M. T. Bassuoni, and A. Shalaby. 2021. “Nanomodified cementitious composites incorporating basalt fiber pellets under tensile and impact loads.” J. Mater. Civ. Eng. 33 (10): 04021260. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003913.
Baloch, W. L., H. Siad, M. Lachemi, and M. Sahmaran. 2021. “A review on the durability of concrete-to-concrete bond in recent rehabilitated structures.” J. Build. Eng. 44 (Dec): 103315. https://doi.org/10.1016/j.jobe.2021.103315.
Barman, M., and B. Hansen. 2018. Comparison of performances of structural fibers and development of a specification for using them in thin concrete overlays. St. Paul, MI: Minnesota DOT.
Birkeland, P. W., and H. W. Birkeland. 1966. “Connections in precast concrete construction.” J. Am. Concr. Inst. 63 (3): 345–368.
Branston, J., S. Das, S. Y. Kenno, and C. Taylor. 2016. “Mechanical behaviour of basalt fibre reinforced concrete.” Constr. Build. Mater. 124 (Oct): 878–886. https://doi.org/10.1016/j.conbuildmat.2016.08.009.
COW (City of Winnipeg). 2015. Portland cement concrete pavement works. CW3310-R17. Winnipeg, MB, Canada: COW.
CSA (Canadian Standards Association). 2018. Cementitious materials for use in concrete. CSA-A3001-18. Mississauga, ON, Canada: CSA.
CSA (Canadian Standards Association). 2019a. Concrete materials and methods of concrete construction/test methods and standard practices for concrete. CSA A23.1/A23.2. Mississauga, ON, Canada: CSA.
CSA (Canadian Standards Association). 2019b. Determination of bond strength of bonded toppings and overlays and of direct tensile strength of concrete, mortar, and grout. CSA A23.2-6B. Mississauga, ON, Canada: CSA.
Detwiler, R., J. Bhatty, and S. Bhattacharja. 1996. Supplementary cementing materials for use in blended cements. Skokie, IL: Portland Cement Association.
Fick, G., and D. Harrington. 2016. Guide specifications for concrete overlays. Ames, IA: National Concrete Pavement Technology Center, Iowa State Univ., Institute for Transportation.
Ghazy, A., M. T. Bassuoni, and A. Shalaby. 2016. “Nano-modified fly ash concrete: A repair option for concrete pavements.” ACI Mater. J. 113 (2): 231–242. https://doi/org/10.14359/51688642.
Hasani, M., F. M. Nejad, J. Sobhani, and M. Chini. 2021. “Mechanical and durability properties of fiber reinforced concrete overlay: Experimental results and numerical simulation.” Constr. Build. Mater. 268 (Jan): 121083. https://doi.org/10.1016/j.conbuildmat.2020.121083.
Hillerborg, A. 1980. “Analysis of fracture by means of the fictitious crack model, particularly for fibre reinforced concrete.” Int. J. Cem. Comp. 2 (4): 177–184.
Jiang, C., K. Fan, F. Wu, and D. Chen. 2014. “Experimental study on the mechanical properties and microstructure of chopped basalt fibre reinforced concrete.” Mater. Des. 58 (Jun): 187–193. https://doi.org/10.1016/j.matdes.2014.01.056.
Kong, D., X. Du, S. Wei, H. Zhang, Y. Yang, and S. P. Shah. 2012. “Influence of nano-silica agglomeration on microstructure and properties of the hardened cement-based materials.” Constr. Build. Mater. 37 (Dec): 707–715. https://doi.org/10.1016/j.conbuildmat.2012.08.006.
Lee, J. J., J. Song, and H. Kim. 2014. “Chemical stability of basalt fiber in alkaline solution.” Fib. Polym. 15 (11): 2329–2334. https://doi.org/10.1007/s12221-014-2329-7.
Lenz, P. 2012. “Concrete-concrete composite potential for shear joints.” Ph.D. thesis, Chair of Concrete Structures, Technical Univ. of Munich.
Li, V. C., H. Stang, and H. Krenchel. 1993. “Micromechanics of crack bridging in fibre reinforced concrete.” Mater. Struct. 26 (8): 486–494. https://doi.org/10.1007/BF02472808.
Mahmoud, K., A. Ghazy, M. T. Bassuoni, and E. El-Salakawy. 2017. “Properties of nanomodified fiber-reinforced cementitious composites.” J. Mater. Civ. Eng. 29 (10): 04017173. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002040.
Mattock, A. H., and N. M. Hawkins. 1972. “Shear transfer in reinforced concrete—Recent research.” PCI J. 17 (2): 55–75. https://doi.org/10.15554/pcij.03011972.55.75.
Mehta, P. K., and P. J. M. Monteiro. 2014. Concrete: Microstructure, properties, and materials. New York: McGraw Hill Education.
Oertel, T., F. Hutter, R. Tänzer, U. Helbig, and G. Sextl. 2013. “Primary particle size and agglomerate size effects of amorphous silica in ultra-high performance concrete.” Cem. Conc. Comp. 37 (Mar): 61–67. https://doi.org/10.1016/j.cemconcomp.2012.12.005.
Romualdi, J. P., and G. B. Batson. 1963. “Mechanics of crack arrest in concrete.” J. Eng. Mech. 89 (3): 147–168. https://doi.org/10.1061/JMCEA3.0000381.
Romualdi, J. P., and J. A. Mandel. 1964. “Tensile strength of concrete affected by uniformly distributed and closely spaced short lengths of wire reinforcement.” J. Proc. 61 (6): 657–672. https://doi.org/10.14359/7801.
Şahmaran, M., M. Al-Emam, G. Yıldırım, Y. E. Şimşek, T. K. Erdem, and M. Lachemi. 2015. “High-early-strength ductile cementitious composites with characteristics of low early-age shrinkage for repair of infrastructures.” Mater. Struct. 48 (5): 1389–1403. https://doi.org/10.1617/s11527-013-0241-z.
Shah, S. P., S. E. Swartz, and C. Ouyang. 1995. Fracture mechanics of concrete: Applications of fracture mechanics to concrete, rock and other quasi-brittle materials. New York: Wiley.
Sharma, S. K., A. A. Kumar, G. D. R. N. Ransinchung, and P. Kumar. 2013. “Micro fiber reinforced cement paste and mortar overlays: A review.” Int. J. Pavement Res. Technol. 6 (6): 765–772. https://doi.org/10.6135/ijprt.org.tw/2013.6(6).765.
Smith, K. D., D. S. Harrington, L. Pierce, P. Ram, and K. L. Smith. 2014. Concrete pavement preservation guide. Washington, DC: Federal Highway Administration.
Soliman, H., and A. Shalaby. 2014. “Characterizing the performance of cementitious partial-depth repair materials in cold climates.” Constr. Build. Mater. 70 (Nov): 148–157. https://doi.org/10.1016/j.conbuildmat.2014.07.114.
Su, N., L. Lou, A. Amirkhanian, S. N. Amirkhanian, and F. Xiao. 2021. “Assessment of effective patching material for concrete bridge deck -A review.” Constr. Build. Mater. 293 (Jul): 123520. https://doi.org/10.1016/j.conbuildmat.2021.123520.
Tada, H., P. C. Paris, and G. R. Irwin. 2000. The stress analysis of cracks handbook. New York: ASME Press.
Wilson, T. P., K. L. Smith, and A. R. Romine. 1999. LTPP pavement maintenance materials: PCC partial-depth spall repair experiment, final report. Washington, DC: Federal Highway Administration.
Wu, C. L., S. M. Tarr, T. M. Refai, M. A. Nagi, and M. J. Sheehan. 1998. Development of ultra-thin whitetopping design procedure. Skokie, IL: Portland Cement Association Research and Development, Portland Cement Association.
Xie, C., M. Cao, M. Khan, H. Yin, and J. Guan. 2020. “Review on different testing methods and factors affecting fracture properties of fiber reinforced cementitious composites.” Constr. Build. Mater. 273 (Mar): 121766. https://doi.org/10.1016/j.conbuildmat.2020.121766.
Yucel, H. E., H. Jashami, M. Sahmaran, M. Guler, and I. O. Yaman. 2013. “Thin ECC overlay systems for rehabilitation of rigid concrete pavements.” Mag. Concr. Res. 65 (2): 108–120. https://doi.org/10.1680/macr.12.00022.
Zhang, J., and V. C. Li. 2002. “Monotonic and fatigue performance in bending of fiber reinforced engineered cementitious composite in overlay system.” Cem. Concr. Res. 32 (3): 415–423. https://doi.org/10.1016/S0008-8846(01)00695-0.
Zhu, Y., Y. Yang, and Y. Yao. 2012. “Use of slag to improve mechanical properties of engineered cementitious composites (ECCs) with high volumes of fly ash.” Constr. Build. Mater. 36 (Nov): 1076–1081. https://doi.org/10.1016/j.conbuildmat.2012.04.031.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Jul 9, 2021
Accepted: Dec 1, 2021
Published online: May 23, 2022
Published in print: Aug 1, 2022
Discussion open until: Oct 23, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- R. Elhadary, M. T. Bassuoni, Bonding Evaluation of Nanosilica-Modified Slag-Based Composites Comprising of Basalt Pellets and Polyvinyl Alcohol Fibers for Shear Joints, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-16162, 36, 2, (2024).
- R. Elhadary, M. T. Bassuoni, Interfacial Bonding between Basalt Fiber/Polymer Pellets and Various Nano-Modified Cementitious Matrices, Journal of Materials in Civil Engineering, 10.1061/(ASCE)MT.1943-5533.0004632, 35, 3, (2023).