Hydraulic and Statistical Analyses of Design Emission Uniformity of Trickle Irrigation Systems
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Irrigation and Drainage Engineering
Volume 138, Issue 9
Abstract
The important evaluation parameter in trickle irrigation is emission uniformity. There are two different methods to calculate emission uniformity; (1) field evaluation for the subunit and (2) using theoretical formulas to calculate emission uniformity during the design period. Emission uniformity is usually divided into two parts, namely, manufacturing, , and hydraulics emission uniformity, . The global emission uniformity is the product of these two parts. Previously, a formula was developed to predict the manufacturing emission uniformity by assuming that when the emitter is tested at a given head, emitter discharges are normally distributed around their mean. This assumption did not apply well to the tested emitters. In this research, the manufacturing part was expressed in terms of the statistical characteristics of the distribution of emitter discharges when tested at a given pressure head. The hydraulic part of emission uniformity, , was expressed in terms of the hydraulic characteristics of the subunit. Many design cases were executed and for each design the matrix of emitters discharges and the hydraulic emission uniformity were calculated. The hydraulic emission uniformity was calculated by using the developed formula. The results obtained from the two methods were found to be closely related. The research involved conducting two sets of experimental work to test several types of emitters and the second set of experiments involved measuring actual emission uniformity of trickle irrigation systems to verify the theoretical formulas to calculate design emission uniformity. From the conducted experiments and the theoretical analysis it was found that for the tested emitters the distribution of emitter discharges, when tested at the same pressure head, around their mean was not normal; it is sufficient to test the emitter at a given head. The values of field emission uniformity were very close to those calculated by an existing and a developed formula. The developed formula provides a simplified method to calculate the hydraulic emission uniformity.
Get full access to this article
View all available purchase options and get full access to this article.
References
Ageel, U. T. (2002). “Investigating a design criterion of trickle irrigation systems.” M.Sc. thesis, Dept. of Irrigation and Drainage, College of Engineering, Univ. of Baghdad, Baghdad, Iraq.
Al-Amoud, A. (2008). “Performance of bubbler system as compared to trickle for large size date palm tree farm.” Paper No., The Canadian Society for Bioengineering, Orleans, ON.
Boman, B. J. (1987). “Manufacturing variation of micro-irrigation emitters.” Proc., Florida State Hort. Soc., Vol. 100, Lake Alfred, FL, 141–143.
Bralts, V. F., Wu, I.-P., and Gitlin, H. M. (1981). “Manufacturing variation and drip irrigation uniformity.” Trans. ASABE, 24(1), 0113–0119.
Bucks, D. A., and Myers, L. E. (1973). “Trickle irrigation-application uniformity from simple emitters.” Trans. ASABE, 16(6), 1108–1111.
Burt, C. M. (2004). “Rapid field evaluation of drip and microspray distribution uniformity.” Irrigation and Drainage Systems, 18(4), 275–297.
Christiansen, J. E. (1942). Irrigation by sprinkling, Bulletin, Univ. of California, Berkeley.
Haijun, L., Zuoxin, L., Qiaosheng, S., and Guanghua, Y. (2009). “Effects of operating pressure on the discharge characteristics of porous pipes as micro-irrigation laterals.” Trans. Chin. Soc. Agric. Eng., 25(2), 1–5.
Handley, D., Vaux, H. J. Jr., and Pickering, N. (1983). Evaluating low volume irrigation systems for emission uniformity, The Regents of the Univ. of California, Oakland, CA.
Howell, T. A., and Hiler, E. A. (1974). “Trickle irrigation lateral design.” Trans. ASABE, 17(5), 0902–0908.
Jahad, U. A. (2010). “Hydraulic comparison of the performance of irrigation drippers in traditional with proposed looped network.” M.Sc. thesis, Dept. of Water Resources, College of Engineering, Univ. of Baghdad, Baghdad, Iraq.
Keller, J., and Karmeli, D. (1974). “Trickle irrigation design parameters.” Trans. ASAE, 17(4), 678–684.
Kirnak, H., Dogan, E., Demir, S., and Yalcin, S. (2004). “Determination of hydraulic performance of trickle irrigation emitters used in irrigation systems in the Harran Plain.” Turk. J. Agric. For., 28(4), 223–230.
Merriam, J. L., and Keller, J. (1978). Farm irrigation system evaluation: A guide for management, Utah State Univ., Logan, UT, 120–230.
Ortega, J. F., Tarjuelo, J. M., and Juan, J. A. (2002). “Evaluation of irrigation performance in localized irrigation systems of semiarid regions (Castilla-La Mancha, Spain).” CIGR E-Journal, 4, 1–17.
Solomon, K. (1979). “Manufacturing variation of trickle emitters.” Trans. ASABE, 22(5), 1034–1038.
Wu, I. P., and Gitlin, H. M. (1973). “Hydraulic and uniformity for drip irrigation.” J. Irrig. Drain., 99(IR2), 157–168.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Feb 18, 2011
Accepted: Feb 7, 2012
Published online: Aug 15, 2012
Published in print: Sep 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.