Protecting Vertical-Wall Abutments with Riprap Mattresses
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Hydraulic Engineering
Volume 135, Issue 6
Abstract
This study addresses the design of riprap mattresses as a scour countermeasure near vertical-wall bridge abutments under clear water flow conditions. It specifically deals with the diameter of riprap, , the lateral extent of mattresses, , and their thickness, . Experiments were performed in a rectangular, sand-bed open channel using different abutment lengths, three riprap stone sizes, and two different sands. The minimum size of stable stones as well as the mattress dimensions depend on the ratio between the abutment length and the flow depth. New equations for the evaluation of and are suggested. The geometric properties of the scour holes which develop at the edge of riprap mattresses are similar to those reported in the literature for spill-through abutments. Although it is not possible to fully arrest scour by winnowing, the corresponding scour depth is negligible when the mattress layer thickness is at least .
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers wish to acknowledge the financial support of the Portuguese Foundation for Science and Technology, through Grant No. UNSPECIFIEDPOCI/ECM/59544/2004.
References
Atayee, A. T., Pagán-Ortiz, J. E., Jones, J. S., and Kilgore, R. T. (1993). “A study of riprap as scour protection for spill-through abutments.” Proc., ASCE Hydraulic Conf., ASCE, New York.
Austroads. (1994). Waterway design—A guide to the hydraulic design of bridges, culverts and floodways, Sydney, Australia.
Cardoso, A. H., Santos, J. S., and Roca, M. (2002). “Effects of flow intensity, obstacle alignment and cross-section geometry on scour at bridge abutments.” Int. J. Sediment Res., 17(2), 102–113.
Chiew, Y. M. (1995). “Mechanics of riprap failure at bridge piers.” J. Hydraul. Eng., 121(9), 635–643.
Chiew, Y. M., and Lim, F. H. (2000). “Failure behavior of riprap layer at bridge piers under live-bed conditions.” J. Hydraul. Eng., 126(1), 43–55.
Eve, N. J., and Melville, B. W. (2000). “Riprap protection of bridge abutments under clear water conditions.” Proc., ASCE Joint Conf. on Water Resources Engineering and Water Resources Planning and Management, ASCE, New York.
Fael, C. M. S. (2007). “Local scour and scour countermeasures at vertical-wall abutments.” Ph.D. dissertation, Univ. da Beira Interior, Covilhã, Portugal (in Portuguese).
Fael, C. M. S., Simarro, G., Martín-Vide, J. P., and Cardoso, A. H. (2006). “Local scour at vertical-wall abutments under clear water flow conditions.” Water Resour. Res., 42, W10408.
Garde, R. J. (1970). “Initiation of motion on a hydrodynamically rough surface. Critical velocity approach.” JIP, 6(2), India.
Hager, W. H., and Oliveto, G. (2002). “Shields’ entrainment criterion in bridge piers.” J. Hydraul. Eng., 128(5), 538–542.
Hanco, S. (1971). “Sur le calcul des affouillements locaux dans la zone de piles de pont.” Proc., 14th Congrés de IAHR, Communication C36 aux, Paris.
Lagasse, P. F., Zevenbergen, L. W., Schall, J. D., and Cooper, P. E. (2001). “Bridge scour and stream instability countermeasures.” Rep. No. FHWA-NH1-01-003, Hydraulic Engineering Circular N° 23 (HEC-23), 2nd Ed., Office of Bridge Technology, Federal Highway Administration, Washington, D.C.
Lauchlan, C. S. (1999). “Countermeasures for pier scour.” Ph.D. thesis, The Univ. of Auckland, Auckland, New Zealand.
Lim, F. H., and Chiew, Y. M. (2001). “Parametric study of riprap failure around bridge piers.” J. Hydraul. Res., 39(1), 61–72.
Melville, B., Ballegooy, S., Coleman, S., and Barkdoll, B. (2006a). “Countermeasure toe protection at spill-through abutments.” J. Hydraul. Eng., 132(3), 235–245.
Melville, B., Ballegooy, S., Coleman, S., and Barkdoll, B. (2006b). “Scour countermeasures for wing-wall abutments.” J. Hydraul. Eng., 132(6), 563– 574.
Melville, B., Ballegooy, S., Coleman, S., and Barkdoll, B. (2007). “Riprap size selection at wing-wall abutments.” J. Hydraul. Eng., 133(11), 1265–1269.
Melville, B., and Coleman, E. (2000). Bridge scour, Water Resources Publications. LLC, Fort Collins, Colo.
Ministry of Works and Development. (1979). “Code of practice for the design of bridge waterways.” CDP 705/C, Civil Division Publication, Wellington, New Zealand.
Neil, C. R. (1967). “Mean velocity criterion for scour of coarse uniform bed-material.” Proc., 12th IAHR Congress, 46–54.
Pagán-Ortiz, J. E. (1991). “Stability of rock riprap for protection at the toe abutments located at the floodplain.” Dept. of Transportation Rep. No. FHWA-RD-91-057:125, Federal Highway Administration, Washington, D.C.
Parker, G., et al. (1998). Countermeasures to protect bridge piers from scour. User’s guide, National Cooperative Highway Research Program, Transportation Research Board, National Research Council, Washington, D.C.
Parola, A. C. (1993). “Stability of riprap at bridge piers.” J. Hydraul. Eng., 119(10), 1080–1093.
Richardson, E. V., and Davis, S. R. (1995). “Evaluating scour at bridges.” Hydraulic Engineering Circular No. 18 (HEC-18). Rep. No. FHWA-IP-90-017:204, FHWA, Washington, D.C.
Unger, J., and Hager, W. H. (2006). “Riprap failure at circular bridge piers.” J. Hydraul. Eng., 132(4), 354–362.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Dec 4, 2007
Accepted: Dec 12, 2008
Published online: May 15, 2009
Published in print: Jun 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.