Thermal Consolidation Theory
This article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 147, Issue 1
Abstract
This study presents an analytical formulation to predict the generation and dissipation of thermal pore pressures and volumetric strains in low permeability soils. The developed relations facilitate mimicking the transient nature of the thermal loads applied to energy geostructures overcoming the commonly adopted assumptions of fully drained or undrained conditions. This theoretical model relies on coupling Darcy’s law with relations predicting the thermal volumetric strains in soils. The developed relations were validated against experimental results under different conditions (e.g., heating rates, confining stresses, and stress states), showing good agreement between the predicted and the experimental results. The developed relations were then used to explain why the maximum thermal pore pressures at the bottom of the tested specimens were observed before the specimen temperature reaches its maximum. Finally, a sensitivity analysis was performed to identify the significance of various parameters to the thermal consolidation process.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code generated or used during the study are available from the corresponding author by request.
Acknowledgments
This work is supported by the US Army Research Laboratory and the US Army Research Office under contract numbers W911NF-20-1-0238, W911NF-16-1-0336, W911NF-17-1-0262, and W911NF-18-1-0068. The discussions and conclusions in this work reflect the opinions of the authors only.
References
Abuel-Naga, H., D. Bergado, A. Bouazza, and G. Ramana. 2007. “Volume change behaviour of saturated clays under drained heating conditions: Experimental results and constitutive modeling.” Can. Geotech. J. 44 (8): 942–956. https://doi.org/10.1139/t07-031.
Abuel-Naga, H., D. Bergado, G. Ramana, L. Grino, P. Rujivipat, and Y. J. Thet. 2006. “Experimental evaluation of engineering behavior of soft Bangkok clay under elevated temperature.” J. Geotech. Geoenviron. Eng. 132 (7): 902–910. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:7(902).
Agar, J., N. Morgenstern, and J. Scott. 1986. “Thermal expansion and pore pressure generation in oil sands.” Can. Geotech. J. 23 (3): 327–333. https://doi.org/10.1139/t86-046.
ASTM. 2016. Standard test methods for measurement of hydraulic conductivity of saturated porous materials using a flexible wall permeameter. ASTM D5084-16a. West Conshohocken, PA: ASTM.
Bag, R., and A. Rabbani. 2017. “Effect of temperature on swelling pressure and compressibility characteristics of soil.” Appl. Clay Sci. 136 (2): 1–7. https://doi.org/10.1016/j.clay.2016.10.043.
Baldi, G., T. Hueckel, and R. Pellegrini. 1988. “Thermal volume changes of the mineral–water system in low-porosity clay soils.” Can. Geotech. J. 25 (4): 807–825. https://doi.org/10.1139/t88-089.
Booker, J. R., and C. Savvidou. 1985. “Consolidation around a point heat source.” Int. J. Numer. Anal. Methods Geomech. 9 (2): 173–184. https://doi.org/10.1002/nag.1610090206.
Burghignoli, A., A. Desideri, and S. Miliziano. 2000. “A laboratory study on the thermomechanical behaviour of clayey soils.” Can. Geotech. J. 37 (4): 764–780. https://doi.org/10.1139/t00-010.
Campanella, R. G. 1965. Effect of temperature and stress on the time-deformation behavior of saturated clay. Berkeley, CA: Univ. of California.
Campanella, R. G., and J. K. Mitchell. 1968. “Influence of temperature variations on soil behavior.” J. Soil Mech. Found. Eng. Div. 94 (3): 709–734.
Carrillo, N. 1942. “Simple two and three dimensional case in the theory of consolidation of soils.” J. Math. Phys. 21 (1–4): 1–5. https://doi.org/10.1002/sapm19422111.
Cekerevac, C., L. Laloui, and L. Vulliet. 2005. “A novel triaxial apparatus for thermo-mechanical testing of soils.” Geotech. Test. J. 28 (2): 161–170. https://doi.org/10.1520/GTJ12311.
Coccia, C. J. R., and J. S. Mccartney. 2016a. “Thermal volume change of poorly draining soils I: Critical assessment of volume change mechanisms.” Comput. Geotech. 80 (Dec): 26–40. https://doi.org/10.1016/j.compgeo.2016.06.009.
Coccia, C. J. R., and J. S. Mccartney. 2016b. “Thermal volume change of poorly draining soils II: Model development and experimental validation.” Comput. Geotech. 80 (Dec): 16–25. https://doi.org/10.1016/j.compgeo.2016.06.010.
Coccia, C. J. R., and J. S. McCartney. 2012. “A thermo-hydro-mechanical true triaxial cell for evaluation of the impact of anisotropy on thermally induced volume changes in soils.” Geotech. Test. J. 35 (2): 227–237. https://doi.org/10.1520/GTJ103803.
Darbari, Z., K. A. Jaradat, and S. L. Abdelaziz. 2017. “Heating–freezing effects on the pore size distribution of a kaolinite clay.” Environ. Earth Sci. 76 (20): 713. https://doi.org/10.1007/s12665-017-7069-8.
Delage, P., N. Sultan, and Y. J. Cui. 2000. “On the thermal consolidation of Boom clay.” Can. Geotech. J. 37 (2): 343–354. https://doi.org/10.1139/t99-105.
Duncan, J. M., and A. Bursey. 2013. “Soil modulus correlations.” In Proc., Geo-Congress 2013—Foundation Engineering in the Face of Uncertainty: Honoring Fred H. Kulhawy, 321–336. Reston, VA: ASCE.
François, B., and L. Laloui. 2010. “An oedometer for studying combined effects of temperature and suction on soils.” Geotech. Test. J. 33 (2): 112–122. https://doi.org/10.1520/GTJ102348.
Ghaaowd, I., A. Takai, T. Katsumi, and J. S. Mccartney. 2017. “Pore water pressure prediction for undrained heating of soils.” Environ. Geotech. 4 (2): 70–78. https://doi.org/10.1680/jenge.15.00041.
Ghahremannejad, B. 2003. “Thermo-mechanical behaviour of two reconstituted clays.” Ph.D. dissertation. Dept. of Civil Engineering, Univ. of Sydney.
Hanna, D., N. Sivakugan, and J. Lovisa. 2011. “Simple approach to consolidation due to constant rate loading in clays.” Int. J. Geomech. 13 (2): 193–196. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000195.
Hueckel, T., and G. Baldi. 1990. “Thermoplasticity of saturated clays: Experimental constitutive study.” J. Geotech. Eng. 116 (12): 1778–1796. https://doi.org/10.1061/(ASCE)0733-9410(1990)116:12(1778).
Hueckel, T., R. Pellegrini, and C. Del Olmo. 1998. “A constitutive study of thermo-elasto-plasticity of deep carbonatic clays.” Int. J. Numer. Ana. Methods Geomech. 22 (7): 549–574. https://doi.org/10.1002/(SICI)1096-9853(199807)22:7%3C549::AID-NAG927%3E3.0.CO;2-R.
Jaradat, K. A., and S. L. Abdelaziz. 2019. “Thermo-mechanical behavior of saturated clays using discrete element modelling.” In Proc., Geo-Congress 2019: Geotechnical Materials, Modeling, and Testing, edited by C. Meehan, S. Kumar, S. Kumar, M. Pando, and J. Coe, 125–134. Reston, VA: ASCE.
Jaradat, K. A., and S. L. Abdelaziz. 2020. “Thermomechanical triaxial cell for rate-controlled heating-cooling cycles.” Geotech. Test. J. 43 (4): 1022–1036. https://doi.org/10.1520/GTJ20180354.
Jaradat, K. A., Z. Darbari, M. Elbakhshwan, S. L. Abdelaziz, S. K. Gill, E. Dooryhee, and L. E. Ecker. 2017. “Heating-freezing effects on the orientation of kaolin clay particles.” Appl. Clay Sci. 150 (1): 163–174. https://doi.org/10.1016/j.clay.2017.09.028.
Juza, J. 1966. “An equation of state for water and steam.” In Steam tables in the critical region and in the range from 1000. Prague, Czech Republic: Academia.
Kwok, C. Y., and M. Bolton. 2010. “DEM simulations of thermally activated creep in soils.” Géotechnique 60 (6): 425–433. https://doi.org/10.1680/geot.2010.60.6.425.
Laloui, L., and C. Cekerevac. 2003. “Thermo-plasticity of clays: An isotropic yield mechanism.” Comput. Geotech. 30 (8): 649–660. https://doi.org/10.1016/j.compgeo.2003.09.001.
Leroueil, S. 1996. “Compressibility of clays: Fundamental and practical aspects.” J. Geotech. Eng. 122 (7): 534–543. https://doi.org/10.1061/(ASCE)0733-9410(1996)122:7(534).
Lima, A., E. Romero, A. Gens, X. L. Li, and J. Vaunat. 2013. “Thermo-hydraulic behaviour of Boom clay using a heating cell: An experimental study.” In Multiphysical testing of soils and shales, edited by L. Laloui and A. Ferrari, 163–168. Berlin: Springer.
Mitchell, J. K., R. G. Campanella, and A. Singh. 1968. “Soil creep as a rate process.” J. Soil Mech. Found. Div. 94 (1): 231–253.
Olgun, C. G., T. Y. Ozudogru, S. L. Abdelaziz, and A. Senol. 2014. “Long-term performance of heat exchanger piles.” Acta Geotech. 10 (5): 553–569. https://doi.org/10.1007/s11440-014-0334-z.
Olson, R. E. 1977. “Consolidation under time-dependent loading.” J. Geotech. Eng. Div. 103 (1): 55–60.
Palomino, A. M., S. E. Burns, and J. C. Santamarina. 2008. “Mixtures of fine-grained minerals–kaolinite and carbonate grains.” Clays Clay Miner. 56 (6): 599–611. https://doi.org/10.1346/CCMN.2008.0560601.
Plum, R., and M. Esrig. 1969. “Some temperature effects on soil compressibility and pore water pressure.” Spec. Rep. 1969 (103): 231.
Robinet, J. C., A. Rahbaoui, F. Plas, and P. Lebon. 1996. “A constitutive thermomechanical model for saturated clays.” Eng. Geol. 41 (1–4): 145–169. https://doi.org/10.1016/0013-7952(95)00049-6.
Savvidou, C., and J. R. Booker. 1988. “Consolidation around a spherical heat source with a decaying power output.” Comput. Geotech. 5 (3): 227–244. https://doi.org/10.1016/0266-352X(88)90004-3.
Savvidou, C., and J. R. Booker. 1989. “Consolidation around a heat source buried deep in a porous thermoelastic medium with anisotropic flow properties.” Int. J. Numer. Anal. Methods Geomech. 13 (1): 75–90. https://doi.org/10.1002/nag.1610130107.
Sheng, D., S. W. Sloan, and A. Gens. 2004. “A constitutive model for unsaturated soils: thermomechanical and computational aspects.” Comput. Mech. 33 (6): 453–465. https://doi.org/10.1007/s00466-003-0545-x.
Sivakugan, N., J. Lovisa, J. Ameratunga, and B. M. Das. 2014. “Consolidation settlement due to ramp loading.” Int. J. Geotech. Eng. 8 (2): 191–196. https://doi.org/10.1179/1939787913Y.0000000017.
Sultan, N., P. Delage, and Y. Cui. 2002. “Temperature effects on the volume change behaviour of Boom clay.” Eng. Geol. 64 (2–3): 135–145. https://doi.org/10.1016/S0013-7952(01)00143-0.
Takai, A., I. Ghaaowd, J. S. Mccartney, and T. Katsumi. 2016. “Impact of drainage conditions on the thermal volume change of soft clay.” In Proc., Geo-Chicago 2016: Geotechnics for Sustainable Energy, edited by A. Farid, A. De, K. Reddy, N. Yesiller, and D. Zekkos, 32–41. Reston, VA: ASCE.
Terzaghi, K. 1925. Erdbaumechanik auf bodenphysikalischer grundlage. Leipzig, Vienna: F. Deuticke.
Towhata, I., P. Kuntiwattanaku, I. Seko, and K. J. S. Ohishi. 1993. “Volume change of clays induced by heating as observed in consolidation tests.” Soils Found. 33 (4): 170–183. https://doi.org/10.3208/sandf1972.33.4_170.
Vega, A., C. J. Coccia, A. El Tawati, and J. S. Mccartney. 2012. “Impact of the rate of heating on the thermal consolidation of saturated silt.” In Proc., GeoCongress 2012: State of the Art and Practice in Geotechnical Engineering, edited by R. Hryciw, A. Athanasopoulos-Zekkos, and N. Yesiller, 4476–4485. Reston, VA: ASCE.
Vega, A., and J. S. Mccartney. 2014. “Cyclic heating effects on thermal volume change of silt.” Env. Geotech. 2 (5): 257–268. https://doi.org/10.1680/envgeo.13.00022.
Yashima, A., S. Leroueil, F. Oka, and I. Guntoro. 1998. “Modelling temperature and strain rate dependent behavior of clays: One dimensional consolidation.” Soils Found. 38 (2): 63–73. https://doi.org/10.3208/sandf.38.2_63.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Apr 17, 2019
Accepted: Aug 10, 2020
Published online: Oct 19, 2020
Published in print: Jan 1, 2021
Discussion open until: Mar 19, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.