Unconfined Compressive Strength of Synthetic and Natural Mine Tailings Amended with Fly Ash and Cement
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 143, Issue 7
Abstract
The objectives of this study were to evaluate the effect of binder amendment on the unconfined compression strength (UCS) of mine tailings and assess applicability of using the amended materials in earthworks. Natural and synthetic (i.e., laboratory prepared) mine tailings were used to assess the effects of tailings particle size and tailings solids content on UCS. Two types of off-specification fly ashes and Types I and II portland cement were used as cementitious binders. Tailings and fly ash mixtures were prepared at 70, 80, and 90% solids content and amended with 10 or 20% binder. Unconfined compression strength tests were conducted on specimens cured for 7 days. In general, UCS increased with an increase in tailings particle size, solids content, and/or increase in ratio of fly ash for amended tailings specimens. A multivariate regression model was developed to predict UCS of tailings amended with fly ash as a function of (1) tailings water content, (2) water-to-binder ratio, and (3) ratio of fly ash. The model was developed using data from synthetic tailings specimens and validated via tests on natural tailings and data compiled from literature. The model is applicable for estimating the UCS of candidate fly ash amended hard rock mine tailings and low plasticity soils (i.e., liquid ). The UCS of high plasticity materials was underpredicted with the model.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support for this study was provided in part by the Mountain Plains Consortium awarded to North Dakota State University through the U.S. Department of Transportation. Support also was provided by Colorado State University. The opinions, findings, conclusions, or recommendations expressed herein are those of the authors and do not necessarily represent the views of the Mountain Plains Consortium, North Dakota State University, or Colorado State University.
References
ACAA (American Coal Ash Association). (2003). “Fly ash facts for highway engineers.”, Federal Highway Administration, Washington, DC.
ACAA (American Coal Ash Association). (2015). “Sustainable construction with coal combustion products.” Farmington Hill, MI.
Alhomair, S. A. (2016). “Hydraulic conductivity of fly ash-amended mine tailings.” M.Sc. thesis, Dept. of Civil and Environmental Engineering, Colorado State Univ., Fort Collins, CO.
Alhomair, S. A., Gorakhki, M. H., and Bareither, C. A. (2016). “Hydraulic conductivity of fly ash-amended mine tailings.” Geotech. Geol. Eng., 1–19.
ARA (Applied Research Associates). (2004). “Guide for mechanistic-empirical design on new and rehabilitated pavement structures.”, National Cooperative Highway Research Program, ERES Division, Champaign, IL.
Arora, S., and Aydilek, A. H. (2005). “Class F fly-ash-amended soils as highway base materials.” J. Mater. Civ. Eng., 640–649.
ASTM. (2007). “Standard test method for particle-size analysis of soils.” ASTM D422-63, West Conshohocken, PA.
ASTM. (2009). “Standard test methods for unconfined compressive strength of compacted soil-lime mixtures.” ASTM D5102, West Conshohocken, PA.
ASTM. (2014a). “Standard test methods for laboratory compaction characteristics of soil using standard effort ( ()).” ASTM D698-12, West Conshohocken, PA.
ASTM. (2014b). “Standard test methods for liquid limit, plastic limit, and plasticity index of soils.” ASTM D4318-10, West Conshohocken, PA.
ASTM. (2014c). “Standard test methods for specific gravity of soil solids by water pycnometer.” ASTM D854-14, West Conshohocken, PA.
ASTM. (2015a). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” ASTM C618-15, West Conshohocken, PA.
ASTM. (2015b). “Standard test methods for slump of hydraulic-cement concrete.” ASTM C143, West Conshohocken, PA.
Aubertin, M., Bussière, B., and Chapuis, R. P. (1996). “Hydraulic conductivity of homogenized tailings from hard rock mines.” Can. Geotech. J., 33(3), 470–482.
Belem, T., Benzaazoua, M., and Bussière, B. (2000). “Mechanical behavior of cemented paste backfill.” Proc., 53rd Canadian Geotechnical Conf., Canadian Geotechnical Society, Ottawa, 373–380.
Benzaazoua, M., Bussière, B., Demers, I., Aubertin, M., Fried, É., and Blier, A. (2008). “Integrated mine tailings management by combining environmental desulphurization and cemented paste backfill: Application to mine Doyon, Quebec, Canada.” Miner. Eng., 21(4), 330–340.
Bin-Shafique, S., Edil, T. B., Benson, C. H., and Senol, A. (2004). “Incorporating a fly-ash stabilized layer into pavement design.” Proc. ICE-Geotech. Eng., 157(4), 239–249.
Blight, G. (2009). Geotechnical engineering for mine waste storage facilities, CRC Press, London.
Bloss, M. (2002). “Below ground disposal (mine backfill).” Paste and thickened tailings: A guide, R. J. Jewell, A. B. Fourie, and E. R. Lord, eds., Univ. of Western Australia, Nedlands, WA, Australia, 103–126.
Bose, B. (2012). “Geo engineering properties of expansive soil stabilized with fly ash.” Electron. J. Geotech. Eng., 17, 1339–1353.
Bussière, B. (2007). “Hydro-geotechnical properties of hard rock tailings from metal mines and emerging geo-environmental disposal approaches.” Can. Geotech. J., 44(9), 1019–1052.
Chesner, W. H., Collins, R. J., and MacKay, M. H. (1998). “User guidelines for waste and by-product materials in pavement construction.”, U.S. Dept. of Transportation, Federal Highway Administration, Washington, DC.
Consoli, N. C., Cruz, R. C., Floss, M. F., and Festugato, L. (2010). “Parameters controlling tensile and compressive strength of artificially cemented sand.” J. Geotech. Geoenviron. Eng., 759–763.
Consoli, N. C., Foppa, D., Festugato, L., and Heineck, K. S. (2007). “Key parameters for strength control of artificially cemented soils.” J. Geotech. Geoenviron. Eng., 197–205.
Daliri, F., Kim, H., Simms, P., and Sivathayalan, S. (2014). “Impact of desiccation on monotonic and cyclic shear strength of thickened gold tailings.” J. Geotech. Geoenviron. Eng., .
Deb, P. S., and Pal, S. K. (2014). “Effect of fly ash on geotechnical properties of local soil-fly ash mixed samples.” Int. J. Res. Eng. Technol., 3(5), 507–516.
Edil, T. B., Acosta, H. A., and Benson, C. H. (2006). “Stabilizing soft fine-grained soils with fly ash.” J. Mater. Civ. Eng., 283–294.
Ercikdi, B., Baki, H., and İzki, M. (2013). “Effect of desliming of sulphide-rich mill tailings on the long-term strength of cemented paste backfill.” J. Environ. Manage., 115(30), 5–13.
Ercikdi, B., Kesimal, A., Cihangir, F., Deveci, H., and Alp, İ. (2009). “Cemented paste backfill of sulphide-rich tailings: Importance of binder type and dosage.” Cem. Concr. Compos., 31(4), 268–274.
Fall, M., Benzaazoua, M., and Ouellet, S. (2005). “Experimental characterization of the influence of tailings fineness and density on the quality of cemented paste backfill.” Miner. Eng., 18(1), 41–44.
FHWA (Federal Highway Administration). (2003). “Fly ash facts for highway engineers.”, U.S. Dept. of Transportation, Washington, DC.
Fredlund, D. G., Rahardjo, H., and Fredlund, M. D. (2012). Unsaturated soil mechanics in engineering practice, Wiley, Hoboken, NJ.
Godbout, J., Bussière, B., Aubertin, M., and Belem, T. (2007). “Evolution of cemented paste backfill saturated hydraulic conductivity at early curing time.” Proc., 60th Canadian Geotechnical Conf. and 8th Joint CGS/IAH-CNC Groundwater Conf., Canadian Geotechnical Society, Ottawa, 2230–2236.
Grice, T. (1998). “Underground mining with backfill.” Proc., 2nd Annual Summit, Mine Tailings Disposal Systems, Australasian Institute of Mining and Metallurgy, Carlton South, Australia.
Hudson-Edwards, K. A., Jamieson, H. E., and Lottermoser, B. G. (2011). “Mine wastes: Past, present, future.” Elements, 7(6), 375–380.
Janz, M., and Johansson, S. E. (2002). “The function of different binding agents in deep stabilization.” Swedish Deep Stabilization Research Centre, Linkoping, Sweden.
Jensen, O. M., and Hansen, P. F. (2001). “Water-entrained cement-based materials: I. Principles and theoretical background.” Cem. Concr. Res., 31(4), 647–654.
Kesimal, A., Yilmaz, E., Ercikdi, B., Alp, I., and Deveci, H. (2005). “Effect of properties of tailings and binder on the short-and long-term strength and stability of cemented paste backfill.” Mater. Lett., 59(28), 3703–3709.
Khalili, A., and Wijewickreme, D. (2008). “New slurry displacement method for reconstitution of highly gap-graded specimens for laboratory element testing.” Geotech. Test. J., 31(5), 424–432.
Khalili, A., Wijewickreme, D., and Wilson, W. (2010). “Mechanical response of highly gap-graded mixtures of waste rock and tailings. Part I: Monotonic shear response.” Can. Geotech. J., 47(5), 552–565.
Klein, K., and Simon, D. (2006). “Effect of specimen composition on the strength development in cemented paste backfill.” Can. Geotech. J., 43(3), 310–324.
LabVIEW [Computer software]. National Instrument Company, Austin, TX.
Lu, N., and Likos, W. J. (2004). Unsaturated soil mechanics, Wiley, Hoboken, NJ.
Mahmood, A. A., and Mulligan, C. N. (2010). “Investigation of the use of mine tailings for unpaved road base.” Proc., Annual Int. Conf. on Soils, Sediments, Water and Energy, Univ. of Massachusetts Amherst, Amherst, MA, 107–117.
Misra, M., Yang, K., and Mehta, R. K. (1996). “Application of fly ash in the agglomeration of reactive mine tailings.” J. Hazard. Mater., 51(1), 181–192.
Morris, P. H., and Williams, D. J. (1997). “Results of field trials of co-disposal of coarse and fine coal waste.” Trans. Inst. Mining Metall., 106, A38–A41.
Nasir, O., and Fall, M. (2010). “Coupling binder hydration, temperature and compressive strength development of underground cemented paste backfill at early ages.” Tunnel. Underground Space Technol., 25(1), 9–20.
Odadjima, H., Noto, S., Nishikawa, J., and Yamazaki, T. (1995). “Cement stabilization of peaty ground with consideration of organic matter.” Proc., Int. Workshop on the Engineering Characteristics and Behavior of Peat, Sapporo, Japan, 131–141.
Ouellet, S., Bussière, B., Aubertin, M., and Benzaazoua, M. (2007). “Microstructural evolution of cemented paste backfill: Mercury intrusion porosimetry test results.” Cem. Concr. Res., 37(12), 1654–1665.
Ouellet, S., Bussière, B., Mbonimpa, M., Benzaazoua, M., and Aubertin, M. (2006). “Reactivity and mineralogical evolution of an underground mine sulphidic cemented paste backfill.” Miner. Eng., 19(5), 407–419.
Park, J. H., Edraki, M., Mulligan, D., and Jang, H. S. (2014). “The application of coal combustion by-products in mine site rehabilitation.” J. Clean. Prod., 84, 761–772.
Popovics, S. (1970). Concrete making materials, McGraw-Hill, New York.
Powers, T. C., and Brownyard, T. L. (1948). “Studies of the physical properties of hardened portland cement paste.” J. Am. Concr. Inst., 43(9), 101–132.
Qian, G., Huang, T., and Bai, S. (2011). “Use of cement-stabilized granite mill tailings as pavement subbase.” J. Mater. Civ. Eng., 1575–1578.
Qiu, Y., and Sego, D. C. (2001). “Lab properties of mine tailings.” Can. Geotech. J., 38(1), 183–190.
Rosa, M. G., Cetin, B., Edil, T. B., and Benson, C. H. (2016). “Development of a test procedure for freeze-thaw durability of geomaterials stabilized with fly ash.” Geotech. Test. J., 39(6), 938–953.
SAS [Computer software]. SAS Institute, Inc., Cary, NC.
Schroeder, R. L. (1994). “The use of recycled materials in highway construction.” Public Roads, Federal Highway Administration, Washington, DC.
Senol, A., Bin-Shafique, M. S., Edil, T. B., and Benson, C. H. (2002). “Use of class C fly ash for stabilization of soft subgrade.” Proc., 5th Int. Congress on Advances in Civil Engineering, Istanbul Technical Univ., Istanbul, Turkey.
Senol, A., Edil, T. B., Bin-Shafique, M. S., Acosta, H. A., and Benson, C. H. (2006). “Soft subgrades’ stabilization by using various fly ashes.” Resour. Conserv. Recycl., 46(4), 365–376.
Senol, A., Etminan, E., and Olgun, C. G. (2012). “Stabilization of clayey soils using fly ash and homopolymer polypropylene.” Proc., Geocongress 2012, ASCE, Reston, VA, 3929–3938.
Swami, R., Pundhir, N., and Mathur, S. (2007). “Kimberlite tailings: A road construction material.” J. Transp. Res. Board, 1989, 131–134.
Tariq, A. (2012). “Synergistic and environmental benefits of using cement kiln dust with slag and fly ash in cemented paste tailings.” Ph.D. dissertation, Civil and Environmental Engineering, Univ. of Western Ontario, London.
Tastan, E. O., Edil, T. B., Benson, C. H., and Aydilek, A. H. (2011). “Stabilization of organic soils with fly ash.” J. Geotech. Geoenviron. Eng., 819–833.
Trzebiatowski, B., Edil, T., and Benson, C. (2004). “Case study of subgrade stabilization using fly ash: State highway 32, Port Washington, Wisconsin.” Beneficial reuse of waste materials in geotechnical and transportation applications, GSP No. 127, A. Aydilek and J. Wartman, eds., ASCE, Reston, VA, 123–136.
USEPA (U.S. Environmental Protection Agency). (1986a). “Handbook for stabilization/solidification of hazardous waste.”, Hazardous Waste Engineering Research Laboratory, Cincinnati.
USEPA (U.S. Environmental Protection Agency). (1986b). “Quality criteria for water.”, Office of Water Regulation and Standard, Washington, DC.
Vizcarra, G. O. C., Casagrande, M. D. T., and da Motta, L. M. G. (2013). “Applicability of municipal solid waste incineration ash on base layers of pavements.” J. Mater. Civ. Eng., 1–7.
Wickland, B. E., and Wilson, G. W. (2005). “Self-weight consolidation of mixtures of mine waste rock and tailings.” Can. Geotech. J., 42(2), 327–339.
Wickland, B. E., Wilson, G. W., and Wijewickreme, D. (2010). “Hydraulic conductivity and consolidation response of mixtures of mine waste rock and tailings.” Can. Geotech. J., 47(4), 472–485.
Wickland, B. E., Wilson, G. W., Wijewickreme, D., and Klein, B. (2006). “Design and evaluation of mixtures of mine waste rock and tailings.” Can. Geotech. J., 43(9), 928–945.
Yeheyis, M. B., Shang, J. Q., and Yanful, E. K. (2009). “Long-term evaluation of coal fly ash and mine tailings co-placement: A site-specific study.” J. Environ. Manage., 91(1), 237–244.
Zhang, L., Ahmari, S., and Zhang, J. (2011). “Synthesis and characterization of fly ash modified mine tailings-based geopolymers.” Constr. Build. Mater., 25(9), 3773–3781.
Zou, D. H., and Li, L. P. (1999). “Strengthening of solidified dilute tailings slurry.” J. Geotech. Geoenviron. Eng., 11–15.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Apr 4, 2016
Accepted: Nov 16, 2016
Published ahead of print: Feb 20, 2017
Published online: Feb 21, 2017
Published in print: Jul 1, 2017
Discussion open until: Jul 21, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.