Assessment of Reinforcement Strains in Very Tall Mechanically Stabilized Earth Walls
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 138, Issue 3
Abstract
The grade raising associated with the Third Runway Project at Seattle-Tacoma International Airport included construction of tall mechanically stabilized earth (MSE) walls, including the near-vertical, two-tier, 26-m North MSE wall and the near-vertical, four-tier, 46-m tall west MSE wall. Twenty reinforcement strips at critical wall cross sections were instrumented with over 500 strain gauges to monitor strains during and following construction. The reinforcement loads inferred from observed strains are of interest because of their great height and global reinforcement stiffness, which place these walls outside the range in height and stiffness used to calibrate commonly used design methods. This paper presents the development and distribution of reinforcement strains measured during and following the construction of these walls. The reinforcement stresses calculated using the original reinforcement load design methods and design friction angle agreed with those inferred from the measured strains. The accuracy of two standard-of-practice and two alternate design methods is evaluated by comparing the reinforcement loads inferred from measured strains to those calculated using the actual friction angle of the reinforced fill material. Advantages and limitations in these design methods are identified, and recommendations for the improvement of some of these methods are provided.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
We thank the Port of Seattle, S. Kyles, and especially the lead geotechnical construction inspector, D. Berta, for providing helpful information about the wall construction. We also appreciate the significant contributions of HNTB Corp., which provided project management and civil engineering services for the MSE walls. We gratefully acknowledge the contributions of M. Bailey of Hart Crowser, Inc., the geotechnical engineer of record, the contractor's instrumentation engineer, P. E. Mikkelsen of GeoMetron, Inc., and instrumentation specialist, D. Yonemitsu, of Yonemitsu Geotechnical Services. Finally, we thank Dr. S. Boyle of Shannon & Wilson, Inc., and Dr. W. J. Neely for helpful discussions and review of the draft manuscript.
References
AASHTO. (2010). AASHTO LRFD bridge design specifications, 5th Ed., American Association of State and Highway Transportation Officials, Washington, DC.
Allen, T. M., Bathurst, R. J., Holtz, R. D., Walters, D., and Lee, W. F. (2004). “New method for prediction of loads in steel reinforced soil walls.” J. Geotech. Geoenviron. Eng., 130(11), 1109–1120.
Allen, T. M., Christopher, B. R., Elias, V., and DiMaggio, J. A. (2001). “Development of the simplified method for internal stability design of mechanically stabilized earth (MSE) walls.” WSDOT Research Rep. WA-RD 513.1.
Bathurst, R. J., Nernheim, A., and Allen, T. M. (2009). “Predicted loads in steel reinforced soil walls using the AASHTO simplified method.” J. Geotech. Geoenviron. Eng., 135(2), 177–184.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Geotechnique, 36(1), 65–78.
Christopher, B. R. (1993). “Deformation response and wall stiffness in relation to reinforced soil wall design.” Ph.D. dissertation, Purdue Univ.
Christopher, B. R., et al. (1990). “Reinforced soil structures, Vol. 1, Design and construction guidelines.” FHWA Rep. FHWA-RD-89-043, U.S. Department of Transportation, Federal Highway Administration, Washington, DC.
Duncan, J. M., Byrne, P., Wong, K. S., and Mabry, P. (1980). “Strength, stress-strain, and bulk modulus parameters for finite element analyses of stresses and movements in soil masses.” Rep. No. UCB/GT/80-01, Dept. of Civil Engineering, Univ. of California, Berkelely, CA.
Ehrlich, M., and Mitchell, J. K. (1994). “Working stress design method for reinforced soil walls,” J. Geotech. Eng., 120(4), 625–645.
Elias, V., and Christopher, B. R. (1996). “Mechanically stabilized earth walls and reinforced soil slopes, design and construction guidelines.” Participants manual, Publication No. FHWA-SA-96-071, (revised 1997), FHWA Demonstration Project 82 Ground Improvement U.S. Dept. of Transportation, Federal Highway Administration, Washington, DC.
Elias, V., Christopher, B. R., and Berg, R. R. (2001). “Mechanically stabilized earth walls and reinforced soil slopes—Design and construction guidelines.” FHWA-NHI-00-043, Federal Highway Administration, Washington, DC.
Hart Crowser, Inc. (2003). “Seismic design summary report, third runway embankment, Sea-Tac International Airport, SeaTac, Washington.” Engineering Rep., prepared for HNTB.
Jewell, R. A., Milligan, G. W. E., Sarsby, R. W., and Dubois, D. (1985). “Interaction bewteen soil and geogrids.” Polymer grid reinforcement, Thomas Telford Ltd., London, UK, 18–30.
Jewell, R. A., and Wroth, C. P. (1987). “Direct shear tests on reinforced sand.” Geotechnique, 37(1), 53–68.
Juran, I., and Schlosser, F. (1978). “Theoretical analysis of failure in reinforced earth structures.” Proc., ASCE Symp. on Earth Reinforcement, ASCE, New York, 528–555.
Lacasse, S., and Nadim, F. (1996) “Uncertainties in characterising soil properties,” Uncertainty in the geologic environment: From theory to practice, GSP No. 58, ASCE, Reston, VA, 49–75.
Lindquist, D. D. (2008). “Seismic modeling of 135-foot-tall MSE wall.” Proc., Geotech. Earthquake Eng. and Soil Dynamics IV, GSP No. 181, ASCE, Reston, VA.
McGown, A., Andrawes, K. Z., and Murray, R. T. (1987). “The influence of lateral boundary yielding on the stresses exerted by backfills.” Soil Structure Interactions, Ecole Nationale des Ponts et Chaussees, Paris, 585–592.
Mitchell, J. K., and Villet, W. C. B. (1987). “Reinforcement of earth slopes and embankments,” NCHRP Rep. 290, Transportation Research Board, National Research Council, Washington, DC.
Palmeira, E. M., and Milligan, G. W. E. (1989). “Scale and other factors affecting the results of pull-out tests of grids buried in sand.” Geotechnique, 39(3), 511–524.
Sankey, J. E., Bailey, M. J., and Chen, B. (2007). “SeaTac third runway: Design and performance of MSE tall wall.” New Horizons in Earth Reinforcement, 5th Int. Symp. on Earth Reinforcement, IS Kyushu 2007, CRC, Fukuoka, Japan, 1–5.
Sankey, J. E., and Soliman, A. (2004). “Tall wall mechanically stabilized earth applications.” Geo-Trans 2004, GSP No. 126, ASCE, Reston, VA, 2149–2158.
Sawicki, A. (2001). Mechanics of reinforced soil, A. A. Balkema Press, Rotterdam.
Schlosser, F. (1978). “History, current development, and future developments of reinforced earth.” Symp. on Soil Reinforcing and Stabilizing Techniques, sponsored by New South Wales Institute of Technology and Univ. of Sydney, Australia.
Schlosser, F., and De Buhan, P. (1991). “Theory and design related to the performance of reinforced soil structures.” Proc., Int. Reinforced Soil Conf., A. McGown, K. Yeo, and K. Z. Andrawes, eds., British Geotechnical Society, Glasgow, Scotland, 1–14.
Schlosser, F., and Segrestin, P. (1979). “Dimensionnement des ouvrages en terre armee par la methode de l’equilibre local.” Int. Conf. on Soil Reinforcement: Reinforced Earth and Other Techniques, Vol. 1, 157–162.
Snedecor, G. W., and Cochran, W. G. (1964). Statistical methods, University of Iowa Press, Iowa City, IA.
Stuedlein, A. W., Allen, T. M., Holtz, R. D., and Christopher, B. R. (2010a). “Factors affecting the development of MSE wall reinforcement strain.” Proc., Earth Retention 2010, GSP 208, ASCE, Reston, VA, 502–511.
Stuedlein, A. W., Bailey, M. J., Lindquist, D. D., Sankey, J., and Neely, W. J. (2010b) “Design and performance of a 46 m high MSE wall.” J. Geotech. Geoenviron. Eng., 136(6), 786–796.
Stuedlein, A. W., Mikkelsen, P. E., and Bailey, M. J. (2007). “Instrumentation and performance of the third runway north MSE wall at Seattle-Tacoma International Airport.” Field measurements in geomechanics 2007, GSP No. 175, J. DiMaggio and P. Osborn, eds., ASCE, 1–14.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Oct 10, 2010
Accepted: Jun 18, 2011
Published online: Jun 21, 2011
Published in print: Mar 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.