Upper-Bound Limit Analysis of Rock Slope Stability with Tensile Strength Cutoff Based on the Optimization Strategy of Dividing the Tension Zone and Shear Zone
Publication: International Journal of Geomechanics
Volume 22, Issue 5
Abstract
The contribution of tensile cracks to the stability of cracked slopes is important. The tensile characteristics of tensile cracks have a significant influence on the stability of rock slopes. Therefore, in this paper, based on the upper-bound limit analysis method and modified M–C failure criterion, an improved failure mode of multislider of rock slopes is established by assuming that the first m − 1 sliders are shear failures and the other n − m + 1 sliders are tensile failures. The superior division of the tension zone and shear zone is realized through the optimized solution and the corresponding value of m. The influences of each parameter on the stability coefficient, failure region, tension zone, and shear zone are emphatically explored. The results show that the accuracy and superiority of the improved failure mode is verified by comparative analysis. The stability coefficient γH/c decreases nonlinearly with an increase in slope angle β and increases nonlinearly with an increase in dimensionless parameter u (the maximum increase in γH/c is up to 37.2%). The critical height of the slope, the whole failure region, and the ground failure length decrease sharply with an increase in β and increase nonlinearly with an increase in u (the critical height increases up to 20%). The critical height of the slope and the whole failure region increase nonlinearly with an increase in the internal friction angle φ. In addition, the ground overload weakens the effect of tensile strength, while seismic force strengthens this effect, but neither is conducive to rock slope stability. In addition, u is beneficial to slope stability, and the tensile characteristics are more significant for steep rock slopes with a small φ. In practical engineering, the energy dissipation and tensile strength characteristics of rock masses should be considered in the process of crack development, especially in the stability evaluation, reinforcement, and protection of high and steep slopes with frequent earthquakes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was financially supported by the National Natural Science Foundation of China (Grant Nos. 51978666 and 41977213), Fundamental Research Funds for the Central Universities (2682021CX007), the Opening fund of Key Laboratory of Geotechnical and Underground Engineering of Ministry of Education (Grant No. KLE-TJGE-B2004), and the Department of Science and Technology of Sichuan Province (Grant Nos. 2020YFH0017, 2021YJ0032, and 2021YJ0390). All financial support are greatly appreciated.
References
Bourne, S. J., and E. J. M. Willemse. 2001. “Elastic stress control on the pattern of tensile fracturing around a small fault network at Nash Point, UK.” J. Struct. Geol. 23 (11): 1753–1770. https://doi.org/10.1016/S0191-8141(01)00027-X.
Brace, W. F. 1960. “An extension of the Griffith theory of fracture to rocks.” J. Geophys. Res. 65 (10): 3477–3480. https://doi.org/10.1029/JZ065i010p03477.
Chen, G.-H., J.-F. Zou, Q.-J. Pan, Z.-H. Qian, and H.-Y. Shi. 2020. “Earthquake-induced slope displacements in heterogeneous soils with tensile strength cut-off.” Comput. Geotech. 124 (6): 103637. https://doi.org/10.1016/j.compgeo.2020.103637.
Chen, W. F. 1975. Limit analysis and soil plasticity. Amsterdam, Netherlands: Elsevier.
Deng, D. P., L. Li, and L. H. Zhao. 2013. “Critical position of tensile cracks and stability analysis in slope near river.” J. Cent. South Univ. 44 (9): 3873–3883.
Duncan, J. M., S. G. Wright, and T. L. Brandon. 2014. Soil strength and slope stability. Chichester, UK: Wiley.
Eberhardt, E., D. Stead, and J. S. Coggan. 2004. “Numerical analysis of initiation and progressive failure in natural rock slopes—The 1991 Randa rockslide.” Int. J. Rock Mech. Min. Sci. 41 (1): 69–87. https://doi.org/10.1016/S1365-1609(03)00076-5.
Fu, H.-L., C.-Y. Wang, and H. Li. 2020. “Active earth pressure for subgrade retaining walls in cohesive backfills with tensile strength cut-off subjected to seepage effects.” J. Cent. South Univ. 27 (7): 2148–2159. https://doi.org/10.1007/s11771-020-4437-4.
Gipprich, T. L., R. K. Snieder, R. W. Jibson, and W. Kimman. 2008. “The role of shear and tensile failure in dynamically triggered landslides.” Geophys. J. Int. 172 (2): 770–778. https://doi.org/10.1111/j.1365-246X.2007.03681.x.
Gong, F. Q., S. Luo, X. B. and Yan, and J. G. 2018. “Linear energy storage and dissipation rule of red sandstone materials during the tensile failure process.” Chin. J. Rock Mech. Eng. 37 (2): 352–363.
He, Y., Y. Liu, Y. B. Zhang, and R. Yuan. 2019. “Stability assessment of three-dimensional slopes with cracks.” Eng. Geol. 252: 136–144. https://doi.org/10.1016/j.enggeo.2019.03.001.
Huang, Y.-H., S.-Q. Yang, P. G. Ranjith, and J. Zhao. 2017. “Strength failure behavior and crack evolution mechanism of granite containing pre-existing non-coplanar holes: Experimental study and particle flow modeling.” Comput. Geotech. 88: 182–198. https://doi.org/10.1016/j.compgeo.2017.03.015.
Kong, J. M., Y. Cui, S. J. Tian, and A. Fa-You. 2009. “Typical case study on the development characteristics of fragmentation-sliding seismic landslide.” J. Sichuan Univ. 41 (3): 119–124.
Li, D. J., L. H. Zhao, L. Li, and X. Cheng. 2015. “Influence of nonlinear shear strength parameters on stability of slopes with cracks subjected to seismic effects based on upper bound limit analysis.” Rock Soil Mech. 36 (5): 1313–1321 and 1327.
Li, Z. W., and X. L. Yang. 2019. “Active earth pressure for retaining structures in cohesive backfills with tensile strength cut-off.” Comput. Geotech. 110: 242–250. https://doi.org/10.1016/j.compgeo.2019.02.023.
Luo, W., J. Li, G. Tang, J. Chen, and C. Dai. 2021. “Upper-bound limit analysis for slope stability based on modified Mohr–Coulomb failure criterion with tensile cutoff.” Int. J. Geomech. 21 (10): 04021184. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002154.
Michalowski, R. L. 2013. “Stability assessment of slopes with cracks using limit analysis.” Can. Geotech. J. 50 (10): 1011–1021. https://doi.org/10.1139/cgj-2012-0448.
Michalowski, R. L. 2017. “Stability of intact slopes with tensile strength cut-off.” Géotechnique 67 (8): 720–727. https://doi.org/10.1680/jgeot.16.P.037.
Michalowski, R. L. 2018. “Failure potential of infinite slopes in bonded soils with tensile strength cut-off.” Can. Geotech. J. 55 (4): 477–485. https://doi.org/10.1139/cgj-2017-0041.
Park, D., and R. L. Michalowski. 2017. “Three-dimensional stability analysis of slopes in hard soil/soft rock with tensile strength cut-off.” Eng. Geol. 229: 73–84. https://doi.org/10.1016/j.enggeo.2017.09.018.
Park, D., and R. L. Michalowski. 2018. “A cone surface in three-dimensional analyses of slopes with tension cut-off.” Geotech. Res. 5 (2): 51–67. https://doi.org/10.1680/jgere.18.00003.
Park, D., Z. Wang, and R. L. Michalowski. 2017. “Consequences of seismic excitation on slopes in soils with a tensile strength cutoff.” Geotech. Front. 278: 304–313.
Paul, B. 1961. “A modification of the Coulomb–Mohr theory of fracture.” J. Appl. Mech. 28 (2): 259–268. https://doi.org/10.1115/1.3641665.
Qin, C. A., G. Q. Chen, H. J. Zheng, and P. Tang. 2019. “Failure of rock bridge at the end and fracture condition under direct shear tests.” Rock Soil Mech. 40 (2): 642–652.
Shukla, S. K., and M. M. Hossain. 2011. “Stability analysis of multi-directional anchored rock slope subjected to surcharge and seismic loads.” Soil Dyn. Earthquake Eng. 31 (5–6): 841–844. https://doi.org/10.1016/j.soildyn.2011.01.008.
Shukla, S. K., S. Khandelwal, V. N. Verma, and N. Sivakugan. 2009. “Effect of surcharge on the stability of anchored rock slope with water filled tension crack under seismic loading condition.” Geotech. Geol. Eng. 27 (4): 529–538. https://doi.org/10.1007/s10706-009-9254-3.
Stead, D., E. Eberhardt, and J. S. Coggan. 2006. “Developments in the characterization of complex rock slope deformation and failure using numerical modelling techniques.” Eng. Geol. 83 (1–3): 217–235. https://doi.org/10.1016/j.enggeo.2005.06.033.
Su, L.-L., C.-n. Sun, F.-w. Yu, and A. Sarfraz. 2018. “Seismic stability analysis of slopes with pre-existing slip surfaces.” J. Mountain Sci. 15 (6): 1331–1341. https://doi.org/10.1007/s11629-017-4759-3.
Zeng, Q. L., W. F. Wang, H. Y. Chen, X. Y. Xue, and G. X. Yuan. 2016. “Characteristics of Zhaojiagou colluviums landslide and its failure mechanism on slope structure, Zhenxiong county.” J. Eng. Geol. 24 (4): 510–518.
Zhang, Y.-b., Y. Liu, R. Yuan, and Y. He. 2021. “Comparison of seismic stability for slopes with tensile strength cut-off and cracks.” J. Mountain Sci. 18: 3336–3347. https://doi.org/10.1007/s11629-021-6777-4.
Zhao, L.-H., X. Chen, Y. B. Zhang, L. Li, and D.-J. Li. 2016. “Stability analysis of seismic slopes with cracks.” Comput. Geotech. 77: 77–90. https://doi.org/10.1016/j.compgeo.2016.04.007.
Zhao, L.-h., X. Cheng, L. Li, J.-q. Chen, and Y. Zhang. 2017a. “Seismic displacement along a log-spiral failure surface with crack using rock Hoek–Brown failure criterion.” Soil Dyn. Earthquake Eng. 99: 74–85. https://doi.org/10.1016/j.soildyn.2017.04.019.
Zhao, L.-h., X. Cheng, H.-c. Dan, Z.-p. Tang, and Y. Zhang. 2017b. “Effect of the vertical earthquake component on permanent seismic displacement of soil slopes based on the nonlinear Mohr–Coulomb failure criterion.” Soils Found. 57 (2): 237–251. https://doi.org/10.1016/j.sandf.2016.12.002.
Zhao, L. H., D. J. Li, H. C. Tan, X. Cheng, and S. Zuo. 2019. “Characteristics of failure area and failure mechanism of a bedding rockslide in Libo county, Guizhou, China.” Landslides 16 (7): 1367–1374. https://doi.org/10.1007/s10346-019-01188-6.
Zhao, L., C. Yu, X. Cheng, S. Zuo, and K. Jiao. 2020. “A method for seismic stability analysis of jointed rock slopes using Barton–Bandis failure criterion.” Int. J. Rock Mech. Min. Sci. 136 (9): 104487. https://doi.org/10.1016/j.ijrmms.2020.104487.
Zhou, J.-W., W.-Y. Xu, X.-G. Yang, C. Shi, and Z.-H. Yang. 2010. “The 28 October 1996 landslide and analysis of the stability of the current Huashiban slope at the Liangjiaren Hydropower Station, southwest China.” Eng. Geol. 114 (1–2): 45–56. https://doi.org/10.1016/j.enggeo.2010.04.001.
Zhou, Z., F. Zhang, Y.-f. Gao, and S. Shu. 2019. “Nested Newmark model to estimate permanent displacement of seismic slopes with tensile strength cut-off.” J. Cent. South Univ. 26 (7): 1830–1839. https://doi.org/10.1007/s11771-019-4137-0.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 22 • Issue 5 • May 2022
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Oct 1, 2021
Accepted: Dec 27, 2021
Published online: Mar 4, 2022
Published in print: May 1, 2022
Discussion open until: Aug 4, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Dejian Li, Wentao Jia, Xiao Cheng, Lianheng Zhao, Yingbin Zhang, Pengcheng Yu, Limit state analysis of stepped sliding of jointed rock slope based on tensile-shear composite failure mode of rock bridges, Bulletin of Engineering Geology and the Environment, 10.1007/s10064-022-02731-x, 81, 6, (2022).