Geogrid Reinforcement for Stiffness Improvement of Railway Track Formation Over Clay Subgrade
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: International Journal of Geomechanics
Volume 21, Issue 9
Abstract
Weak subgrade condition generally develops large settlements in ballasted tracks, leading to adverse performance. To ameliorate such problems, a commonly adopted technique is to provide a thick cushion of granular subballast/blanket over the subgrade. Owing to scarcity of natural resources, this is often a costly proposition. In the present study, application of geogrid reinforcement for possible reduction of the subballast thickness has been explored through large model plate load tests. The investigations include both single and multiple layers of reinforcement in the subballast. With geogrid reinforcement, stiffness and resiliency of track beds were found to have increased markedly. Optimum depth of single-layer geogrid in the subballast giving maximum performance improvement was about 0.33 times the loading diameter. The corresponding improvement in stiffness of the track bed was about 77%. With multiple layers of geogrid in the subballast, the improvement in stiffness was as high as 99%. It is observed that with just one layer of geogrid in the subballast, its thickness can be reduced by 33% (i.e., from 600 to 400 mm).
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Most of the data used during the present study are included in the article. Few data not reported herein (i.e., reloading surface deformation responses), are available from the corresponding author by request.
Acknowledgments
The financial support for this work from HMBS Textiles Pvt. Ltd., Delhi (IIT/SRIC/CE/MRRT/2013-2014/40) is gratefully acknowledged. The authors are thankful to Prof. K. S. Reddy and Prof. B. B. Pandey (deceased) for their valuable comments and suggestions.
Notation
The following symbols are used in this paper:
- Al
- area of hysteresis loop (MN/m2-mm);
- a
- radius of loading plate (mm);
- b
- width of reinforcement (mm);
- CBRsb
- California bearing ratio of subballast (%);
- CBRsg
- California bearing ratio of subgrade soil (%);
- CBRss
- California bearing ratio of subsoil (%);
- Cc
- coefficient of curvature;
- Cu
- coefficient of uniformity;
- csg
- cohesion of subgrade soil (kPa);
- css
- cohesion of subsoil (kPa);
- D
- diameter of loading plate (mm);
- Ev1
- vertical strain modulus under loading (MPa);
- Ev2
- vertical strain modulus under reloading (MPa);
- Evr
- modulus of the reinforced track bed (MPa);
- Evu
- modulus of the unreinforced track bed (MPa);
- hsb
- thickness of subballast (mm);
- hsg
- thickness of subgrade (mm);
- hss
- thickness of subsoil (mm);
- MDD
- maximum dry density (kN/m3);
- N
- number of reinforcement layers;
- OMC
- optimum moisture content (%);
- P
- load applied (kN);
- PIM1
- Percentage Improvement in Modulus Ev1 (%);
- PIM2
- Percentage Improvement in Modulus Ev2 (%);
- p(r)
- contact pressure at distance r (kN/m2);
- p
- average bearing pressure (kN/m2);
- s
- settlement (mm);
- u
- depth to top reinforcement layer (mm);
- x
- horizontal distance from center of loading plate (mm);
- Δh
- spacing between reinforcement layers (mm);
- ϕsb
- peak friction angle of subballast (°);
- ϕsg
- peak friction angle of subgrade (°);
- ϕss
- peak friction angle of subsoil (°);
- μ
- Poisson’s ratio;
- σz,
- vertical normal stress at depth z (kN/m2);
- σr
- radial normal stress at radial distance r (kN/m2);
- σθ
- tangential normal stress at angle θ (kN/m2); and
- ψsb
- peak dilation angle of subballast (°).
References
Adam, C., D. Adam, F. Kopf, and I. Paulmichl. 2009. “Computational validation of static and dynamic plate load testing.” Acta Geotech. 4 (1): 35–55. https://doi.org/10.1007/s11440-008-0081-0.
Adams, T. M., and J. G. Collin. 1997. “Large model spread footing load tests on geosynthetic reinforced soil foundations.” J. Geotech. Geoenviron. Eng. 123 (1): 66–72. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:1(66).
Alawaji, H. A. 2001. “Settlement and bearing capacity of geogrid-reinforced sand over collapsible soil.” Geotext. Geomembr. 19 (2): 75–88. https://doi.org/10.1016/S0266-1144(01)00002-4.
Ashmawy, A. K., and P. L. Bourdeau. 1995. “Geosynthetic-reinforced soils under repeated loading: A review and comparative design study.” Geosynth. Int. 2 (4): 643–678. https://doi.org/10.1680/gein.2.0029.
ASTM. 2003. Standard test method for unconsolidated-undrained triaxial compression test on cohesive soils. ASTM D2850-03. West Conshohocken, PA: ASTM.
ASTM. 2005. Standard test methods for liquid limit, plastic limit, and plasticity index of soils. ASTM D4318-05. West Conshohocken, PA: ASTM.
ASTM. 2006. Standard practice for classification of soils for engineering purposes (unified soil classification system). ASTM D2487-17. West Conshohocken, PA: ASTM.
ASTM. 2012. Standard test methods for laboratory compaction characteristics of soil using modified effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3)). ASTM D1557-12. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test method for determining tensile properties of geogrids by the single or multi-rib tensile method. ASTM D6637/D6637M-15. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for California Bearing Ratio (CBR) of laboratory-compacted soils. ASTM D1883-16. West Conshohocken, PA: ASTM.
ASTM. 2017. Standard test method for consolidated undrained direct simple shear testing of cohesive soils. ASTM D6528-17. West Conshohocken, PA: ASTM.
Bathurst, R. J., A. Nernheim, D. L. Walters, T. M. Allen, P. Burgess, and D. D. Saunders. 2009. “Influence of reinforcement stiffness and compaction on the performance of four geosynthetic-reinforced soil walls.” Geosynth. Int. 16 (1): 43–59. https://doi.org/10.1680/gein.2009.16.1.43.
Bathurst, R. J., and G. P. Raymond. 1987. “Geogrid reinforcement of ballasted track.” Transp. Res. Rec. 1153: 8–14.
Bergado, D. T., R. Shivashankar, M. C. Alfaro, J. C. Chai, and A. S. Balasubramaniam. 1993. “Interaction behavior of steel grid reinforcements in a clayey sand.” Géotechnique 43 (4): 589–603. https://doi.org/10.1680/geot.1993.43.4.589.
Biswas, A., M. A. Krishna, and S. K. Dash. 2013. “Influence of subgrade strength on the performance of geocell-reinforced foundation systems.” Geosynth. Int. 20 (6): 376–388. https://doi.org/10.1680/gein.13.00025.
Boussinesq, M. J. 1885. Application des potentiels a l'etude de l'equilibre et du mouvement des solides elastiques, principalement au calcul des deformations et des pressions que produisent, dans ces solides, des efforts quelconques exerces sur une petite partie de leur surface ou de leur interieur: Memoire suivi de notes etendues sur divers points de physique mathematique et d'analyse. Paris: GauthierVillars.
Brown, S. F., J. Kwan, and N. H. Thom. 2007. “Identifying the key parameters that influence geogrid reinforcement of railway ballast.” Geotext. Geomembr. 25 (6): 326–335. https://doi.org/10.1016/j.geotexmem.2007.06.003.
Chummar, A. V. 1972. “Bearing capacity theory from experimental results.” J. Soil Mech. Found. Div. 98 (12): 1311–1324. https://doi.org/10.1061/JSFEAQ.0001816.
Das, B. M. 2019. Advanced soil mechanics. New York: CRC Press, Taylor and Francis Group.
Das, B. M., and K. H. Khing. 1994. “Foundation on layered soil with geogrid reinforcement—Effect of a void.” Geotext. Geomembr. 13 (8): 545–553. https://doi.org/10.1016/0266-1144(94)90018-3.
Department of the Army and Air Force. 1991. Rail road track standards. TM 5-628/AFR 91-44. Washington, DC: Dept. of the Army and Air Force.
DIN (Deutsches Institut für Normung). 2001. Determining the deformation and strength characteristics of soil by the plate loading test. DIN 18134. Berlin: DIN, Beuth Verlag GmbH.
Eshkevari, S. S., A. J. Abbo, and G. Kouretzis. 2019. “Bearing capacity of strip footings on sand over clay.” Can. Geotech. J. 56 (5): 699–709. https://doi.org/10.1139/cgj-2017-0489.
Esveld, C. 2014. Modern railway track. Zaltbommel, Netherlands: MRT-Productions.
Fakher, A., and C. J. F. P. Jones. 2001. “When the bending stiffness of geosynthetic reinforcement is important.” Geosynth. Int. 8 (5): 445–460. https://doi.org/10.1680/gein.8.0202.
Fernandes, G., E. M. Palmeira, and R. C. Gomes. 2008. “Performance of geosynthetic-reinforced alternative sub-ballast material in a railway track.” Geosynth. Int. 15 (5): 311–321. https://doi.org/10.1680/gein.2008.15.5.311.
Gabr, M. A., and J. H. Hart. 2000. “Elastic modulus of geogrid-reinforced sand using plate load tests.” Geotech. Test. J. 23 (2): 245–250. https://doi.org/10.1520/GTJ11049J.
Giroud, J. P., and L. Noiray. 1981. “Geotextile reinforced unpaved road design.” J. Geotech. Eng. Div. 107, 1233–1254.
Guido, V. A., D. K. Chang, and M. A. Sweeney. 1986. “Comparison of geogrid and geotextile reinforced earth slabs.” Can. Geotech. J. 23 (4): 435–440. https://doi.org/10.1139/t86-073.
Handy, R. L. 1985. “The arch in soil arching.” J. Geotech. Eng. 111 (3): 302–318. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:3(302).
Jewell, R. A. 1990. “Reinforcement bond capacity.” Géotechnique 40 (3): 513–518. https://doi.org/10.1680/geot.1990.40.3.513.
Khing, K. H., B. M. Das, V. K. Puri, S. C. Yen, and E. E. Cook. 1994. “Foundation on strong sand underlain by weak clay with geogrid at the interface.” Geotext. Geomembr. 13: 199–206. https://doi.org/10.1016/0266-1144(94)90035-3.
Koerner, R. M. 1990. Designing with geosynthetics. Englewood Cliffs, NJ: Prentice Hall.
Lackner, C., D. T. Bergado, and S. Semprich. 2013. “Prestressed reinforced soil by geosynthetics - Concept and experimental investigations.” Geotext. Geomembr. 37: 109–123. https://doi.org/10.1016/j.geotexmem.2013.02.002.
Lamberchts, J. R., and G. A. Leonards. 1978. “Effects of stress history on deformation of sand.” J. Geotech. Eng. 104 (11): 1371–1387.
Leng, J., and M. A. Gabr. 2002. “Characteristics of geogrid-reinforced aggregate under cyclic load.” Transp. Res. Rec. 1786 (1): 29–35. https://doi.org/10.3141/1786-04.
Li, D., and E. T. Selig. 1998. “Method for railroad track foundation design. I: Development.” J. Geotech. Geoenviron. Eng. 124 (4): 316–322. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:4(316).
McGown, A., K. C. Yeo, and I. Yogarajah. 1990. “Identification of a dynamic interlock mechanism.” In Proc., Int. Reinforced Soil Conf. on Performance of Reinforced Soil Structures, edited by A. McGown, K. Yeo, and K. Z. Andrawes, 377–379. London: Thomas Telford.
Meyerhof, G. G. 1974. “Ultimate bearing capacity of footings on sand layer overlying clay.” Can. Geotech. J. 11 (2): 223–229. https://doi.org/10.1139/t74-018.
Ministry of Railways. 2020. Indian railways permanent way manual (IRPWM). New Delhi, India: Ministry of Railways.
Moraci, N., G. Cardile, D. Gioffrè, M. C. Mandaglio, L. Calvarano, and L. Carbone. 2014. “Soil geosynthetic interaction: Design parameters from experimental and theoretical analysis.” Transp. Infrastruct. Geotechnol. 1 (2): 165–227. https://doi.org/10.1007/s40515-014-0007-2.
Raymond, G. P. 2002. “Reinforced ballast behavior subjected to repeated load.” Geotext. Geomembr. 20 (1): 39–61. https://doi.org/10.1016/S0266-1144(01)00024-3.
Raymond, G. P., and R. J. Bathurst. 1987. “Performance of large-scale model single tie-ballast systems.” Transp. Res. Rec. 1131: 7–14.
RDSO (Research Design and Standard Organisation). 2007. Guidelines for blanket layer provision on track formation. RDSO-GE-0011. New Delhi, India: Ministry of Railways.
Sadeghi, J., A. R. T. Kian, and M. Fallah. 2021. “Experimental investigation of mechanical properties of ballast contaminated with wet sand materials.” Int. J. Geomech. 21 (1): 04020241. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001886.
Sadeghi, J., A. R. T. Kian, H. Ghiasinejad, M. F. Moqaddam, and S. Motevalli. 2020a. “Effectiveness of geogrid reinforcement in improvement of mechanical behavior of sand-contaminated ballast.” Geotext. Geomembr. 48 (6): 768–779. https://doi.org/10.1016/j.geotexmem.2020.05.007.
Selig, E. T., and K. E. McKee. 1961. “Static and dynamic behavior of small footings.” J. Soil Mech. Found. Div. 87 (6): 29–45. https://doi.org/10.1061/JSFEAQ.0000378.
Terzaghi, K. 1943. Theoretical soil mechanics. New York: John Wiley & Sons.
TolouKian, A. R., J. Sadeghi, and J. A. Zakeri. 2018. “Large-scale direct shear tests on sand-contaminated ballast.” Proc. Inst. Civ. Eng. Geotech. Eng. 171 (5): 451–461. https://doi.org/10.1680/jgeen.17.00107.
Tolou Kian, A. R., J. Sadeghi, and J. Zakeri. 2020. “Influences of railway ballast sand contamination on loading pattern of pre-stressed concrete sleeper.” Constr. Build. Mater. 233: 117324. https://doi.org/10.1016/j.conbuildmat.2019.117324.
Ullidtz, P. 1987. Pavement analysis. New York: Elsevier Science.
Xu, C., X. Zhang, J. Han, and Y. Yang. 2019. “Two-dimensional soil-arching behavior under static and cyclic loading.” Int. J. Geomech. 19 (8): 04019091. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001482.
Yetimoglu, T., J. T. H. Wu, and A. Saglamer. 1994. “Bearing capacity of rectangular footings on geogrid-reinforced sand.” J. Geotech. Eng. 120 (12): 2083–2099. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:12(2083).
Yoshimi, Y., F. Kuwabara, and K. Tokimatsu. 1975. “One-dimensional volume change characteristics of sands under very low confining stresses.” Soils Found. 15 (3): 51–60. https://doi.org/10.3208/sandf1972.15.3_51.
Zhou, H., and X. Wen. 2008. “Model studies on geogrid- or geocell-reinforced sand cushion on soft soil.” Geotext. Geomembr. 26 (3): 231–238. https://doi.org/10.1016/j.geotexmem.2007.10.002.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Nov 30, 2020
Accepted: May 1, 2021
Published online: Jun 25, 2021
Published in print: Sep 1, 2021
Discussion open until: Nov 25, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Nitin Tiwari, Neelima Satyam, Anand J. Puppala, Closure to “Effect of Synthetic Geotextile on Stabilization of Expansive Subgrades: Experimental Study”, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-15429, 35, 5, (2023).
- Vishnu Diyaljee, Discussion of “Effect of Synthetic Geotextile on Stabilization of Expansive Subgrades: Experimental Study”, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-14114, 35, 5, (2023).
- Sujit Kumar Dash, Anjan Majee, A Study on CBR of Railway Track Foundations with Geosynthetic Reinforcement, Indian Geotechnical Journal, 10.1007/s40098-023-00710-x, (2023).
- Qishu Zhang, Wuming Leng, Junli Dong, Fang Xu, Dynamic Response Characteristics of Railway Subgrade Using a Newly-Developed Prestressed Reinforcement Structure: Case Study of a Model Test, Materials, 10.3390/ma15196651, 15, 19, (6651), (2022).
- Saif Alzabeebee, Marwah Abbas Hadi, Suraparb Keawsawasvong, Influence of interference of moving trains on the settlement and critical velocity of ballastless railway track, Innovative Infrastructure Solutions, 10.1007/s41062-022-00991-w, 8, 1, (2022).
- Shahbaz Dandin, Mrudula Kulkarni, Maheboobsab Nadaf, Model Testing on PET Bottle Mattress with Aggregate Infill as Reinforcement Overlaying on Fly Ash Under Circular Loading, Recent Trends in Construction Technology and Management, 10.1007/978-981-19-2145-2_59, (779-795), (2022).