Ashland Tank‐Collapse Investigation
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Performance of Constructed Facilities
Volume 3, Issue 3
Abstract
On January 2, 1988, a 4,000,000‐gallon‐capacity oil storage tank at the Ashland Petroleum Company Floreffe Terminal near West Elizabeth, Pennsylvania, collapsed as it was being filled to capacity for the first time since its reconstruction. The tank had been dismantled in Cleveland, Ohio, after more than 40 years of service, and reconstructed at the Floreffe site in 1986. The National Institute of Standards and Technology (NIST) conducted an independent investigation into the physical cause of the Ashland tank collapse. It was determined that the failure was caused by a brittle fracture of the tank shell, which initiated from a defect that existed prior to reconstruction of the tank. Complete rupture of the tank shell occurred because the steel did not possess adequate toughness at the operating temperature to prevent brittle‐fracture propagation. The collapse shows the importance of using steel with sufficient fracture toughness to prevent propagation of a brittle fracture in tanks, when sudden failure would mean unacceptable human, environmental, or economic losses.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Barsom, J. M., and Rolfe, S. T. (1970). “Correlations between and charpy‐V‐notch test results in the transition temperature range.” Impact Testing of Metals, ASTM STP 466, American Society for Testing and Materials, Philadelphia, Pa.
2.
Barsom, J. M., and Rolfe, S. T. (1982). Fracture and fatigue control in structures. 2nd Ed., Prentice‐Hall, Inc., Englewood Cliffs, N.J.
3.
“Fractography.” (1987). ASM Metals Handbook, 9th Ed., 12, American Society for Metals, Metals Park, Ohio.
4.
Gross, J. L., et al. (1988). “Investigation into the Ashland oil tank collapse on January 2, 1988.” NBSIR 88‐3792, National Bureau of Standards, Gaithersburg, Md.
5.
Hall, W. J., Nordell, W. J., and Munse, W. H. (1962). “Studies of welding procedures.” Weld. J., (Res. Supp.) 41(11).
6.
Mesloh, R. E., et al. (1988). “Failure investigation of Ashland oil tank No. 1338 at Floreffe, Pennsylvania.” Battelle Columbus Division, Columbus, Ohio.
7.
Pellini, W. S., and Puzak, P. P. (1963). “Fracture analysis diagram procedures for the fracture‐safe engineering design of steel structures.” Bull. No. 88, Welding Research Council, New York, N.Y.
8.
Pellini, W. S. (1976). “Principles of structural integrity technology.” Office of Naval Research, Arlington, Va.
9.
Raju, I. S., and Newman, J. C. (1979). “Analysis of surface cracks in finite plates under tension or bending loads.” NASA TP‐1578, National Aeronautics and Space Administration, Langley Research Center, Hampton, Va.
10.
“Report of the Investigation into the Collapse of Tank 1338.” (1988). Commonwealth of Pennsylvania, Harrisburg, Pa.
11.
“Rules for construction of pressure vessels.” (1986). Boiler and Pressure Vessel Code, Section VIII, American Society of Mechanical Engineers, New York, N.Y.
12.
“Standard test method for plane‐strain fracture toughness for metallic materials.” (1983). ASTM E‐399‐83, American Society for Testing and Materials, Philadelphia, Pa.
13.
“Standard method for conducting drop‐weight testing of metallic materials.” (1985). ASTM E‐208‐85, American Society for Testing and Materials, Philadelphia, Pa.
14.
“Standard methods of tension testing of metallic materials.” (1986a). ASTM E‐8‐86, American Society for Testing and Materials, Philadelphia, Pa.
15.
“Standard methods for notched bar impact testing of metallic materials.” (1986b). ASTM E‐23‐86, American Society for Testing and Materials, Philadelphia, Pa.
16.
“Standard test method for a measure of fracture toughness.” (1987). ASTM E‐813‐87, American Society for Testing and Materials, Philadelphia, Pa.
17.
“Welded steel tanks for oil storage.” (1984). API Standard 650, 7th Ed., Revision 1, American Petroleum Institute, Washington, D.C.
Information & Authors
Information
Published In
Journal of Performance of Constructed Facilities
Volume 3 • Issue 3 • August 1989
Pages: 144 - 162
Copyright
Copyright © 1989 ASCE.
History
Published online: Aug 1, 1989
Published in print: Aug 1989
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.